THERMAL-DECOMPOSITION PROCESSES OF SOME ELECTRICALLY CONDUCTING POLYMERS INVESTIGATED BY DIRECT PYROLYSIS MASS-SPECTROMETRY

Thermal decomposition processes of poly(thio-1,4-phenylene) (PPS), polythiophene (PT) and polyaniline (PAn) were investigated by direct pyrolysis EI or CI mass spectrometry (DPMS). They can provide up to heptemer pyrolynates and give some structure properties. The results indicate that the thermal degradation all undergoes in radical decomposition, PPS pyrolyzes into linear and cyclic oligmers, but PT and PAn pyrolyze only into linear oligmers.

GAMMA-RADIATION INDUCED CROSS-LINKED PEO-LICLO4 SOLID-ELECTROLYTE SYSTEM

Aimed at raising the room temperature ionic conductivity of PEO-based solid polymer electrolyte and considered that the ionic conduction preferentially occurs in the amorphous phase, we lightly crosslinked the high MW PEO through gamma-irradiation and further suppressed the residual crystallinity by plasticizing with propylene carbonate. By incorporating LiClO4 salt to the above described polymer host, the ambient (25 degrees C) ionic conductivity of the electrolyte system could reach as high as 6.8 X 10(-4) S/cm. As the electrolyte was a crosslinked system, it was mechanically self-supportable. Based on the preliminary results of the electrochemical performance of the secondary lithium battery, assembled by using this kind of solid electrolyte and polyaniline as positive electrode, it is realized that the electrolyte thus prepared is of high expectancy.

PROTONIC ACID-DOPING OF POLY-ORTHO-METHYLANILINE

Poly-o-methylaniline (poly-o-toluidine) was doped by some protonic acids. It was found that the acidity, molecular size and oxidizing ability of protonic acids affected the doping level and conductivity of polymer obtained to some extent. The organic acid

PREPARATION AND CHARACTERIZATION OF ISOPOLYMOLYBDIC ANIONS DOPED POLYPYRROLE (IPOMO/PPY) FILM ELECTRODE

Isopolymolybdic anion doped polypyrrole film electrode was prepared by electrochemical polymerization of pyrrole in 0.5 mol.L-1 H2SO4 aqueous solution containing isopolymolybdic anions. The film thus prepared has good stability upon potential cycling in s

ELECTRICAL CHARACTERIZATION INDUCED IN PERNIGRANILINE BY POTASSIUM-ION IMPLANTATION

The electrical conductivities of pernigraniline after ion implantation with potassium ions were studied experimentally. Pernigraniline films were irradiated with doses ranging from 1 x 10(13) to 1 x 10(17) K+ ions/cm2 at 40 keV. The electrical conductivit

PREPARATION AND PROPERTIES OF POLYPYRROLE FILM DOPED WITH A DAWSON-TYPE HETEROPOLYANION

The electropolymerization of pyrrole in the presence of Dawson-type tungstophosphate yields a polypyrrole (PPy) film doped with tungstophosphate anions on the electrode surfaces. The electrochemical behaviour of this film was described, and the stability

STUDY OF A 1/12 PHOSPHOMOLYBDIC ANION DOPED POLYPYRROLE FILM ELECTRODE AND ITS CATALYSIS

A phosphomolybdic anion doped polypyrrole (PMo12O403- + PPy) film electrode has been prepared by electrochemical polymerization of pyrrole in an aqueous solution of 0.5 mol l-1 H2SO4 or 0.5 mol l-1 KNO3 containing PMo12O403- anions, and characterized by scanning electron microscopy and in-situ UV-visible spectroelectrochemical methods. The film electrode obtained is very stable upon potential cycling in acidic solution, but not in neutral solution. The catalytic effect of the film electrode on the reduction of ClO3- and BrO3- was studied.

SYNTHESIS AND CHARACTERIZATION OF POLY-ORTHO-METHYLANILINE WITH DIFFERENT DEGREES OF OXIDATION

Poly-ortho-methylanilines (POT) in three states fully oxidized, fully reduced and oxidized in varying degrees were synthesized by the reaction of common POT (C-POT) having nearly equal amounts of benzenediamine and quinonediimine units with iodine or phenyl-hydrazine, and the resulting polymers were characterized by IR, C-13-NMR, SEM and elemental analysis. The results showed that the quinonediimine unit in C-POT could be reduced by phenylhydrazine to the benzenediamine unit, forming the polymer with low OD (oxidation degree) or in a fully reduced state and that iodine-oxidation resulted in the increase of quinonediimine unit and decrease of benzenediamine unit. The solubility and flexibility of the formed polymers depend strongly on the amount of quinonediimine unit in it. It is necessary to reduce the content of quinonediimine structure unit in order to improve the solubility of aniline-class polymers.

EFFECTS OF DOPANT AND SOLVENT ON THE PROPERTIES OF POLYPYRROLE - INVESTIGATIONS WITH CYCLIC VOLTAMMETRY AND ELECTROCHEMICALLY INSITU CONDUCTIVITY

A new method for electrochemically in situ conductivity measurements based on a reusable glassy carbon disc carbon fibre array double electrode is described. Using this technique and cyclic voltammetry, we have investigated the effects of the doping anion and solvent on the electrochemical properties of polypyrrole film. The electroactivity and potential dependent conductivity of polypyrrole film are strongly affected by solvent and the doping anion's solubility in the solvent, and also by the history of electrochemical treatments in different electrolyte solutions. It is very interesting that NO3-doped polypyrrole can completely keep its conducting state (doped state) at a reasonably negative potential (eg -0.8 V vs. sce) in acetonitrile solutions.

ELECTROCHEMICAL STUDY OF ISOPOLY AND HETEROPOLY OXOMETALLATE FILM MODIFIED MICROELECTRODES .5. PREPARATION AND ELECTROCHEMICAL-BEHAVIOR OF A 2/18-MOLYBDODIPHOSPHATE ANION MONOLAYER MODIFIED ELECTRODE

In this paper a carbon fibre (CF) microelectrode modified with the 2:18-molybdodiphosphate anion by simple adsorption is described and its electrochemical behaviour is reported. The 2:18-molybdodiphosphate anion (alpha-P2Mo18O626-), which is a Dawson structure, undergoes five successive multielectron reductions in acidic solution. The first three redox waves correspond to the two-electron process, and the last two waves are four-electron and six-electron processes respectively. On the basis of the experimental results it is shown that the electrode process of alpha-P2Mo18O626- on the CF electrode in acidic solution is simultaneously controlled by the diffusion and adsorption of alpha-P2Mo18O626- anions. When the concentration of the alpha-P2Mo18O626- in the solution is reduced, the electrode process mainly exhibits non-diffusion-controlled behaviour, and the diffusion-limited process takes over as the concentration of alpha-P2Mo18O626- becomes higher. The CF electrode modified with a thin film of alpha-P2Mo18O626- exhibits very good stability and redox behaviour in aqueous acidic solution. The alpha-P2Mo18O626- is reduced to heteropoly blue, with an accompanying protonation process. The addition of more than six electrons to the alpha-P2Mo18O626- anion in an aqueous solution does not result in its decomposition. The result obtained is not the same as that reported previously.

ISOPOLYMOLYBDIC ACID-POLY(4-VINYL)PYRIDINE FILM MODIFIED ELECTRODE

Electrochemical polymerization of 4-vinylpyridine produced a uniform poly(4-vinyl)pyridine(PVP) film on the glassy carbon (GC) electrode surface. The isopolymolybdic acid-PVP film-modified electrode was prepared by soaking the PVP/GC electrode in the 0.05 M H2SO4 aqueous solution containing 0.005 M isopolymolybdic acid (H4Mo8O26). The latter (catalyst) is incorporated and held in the PVP film electrostatically. The electrochemical behavior and electrocatalytic properties of this H4Mo8O26-PVP/GC electrode was described. The results indicate that this modified electrode has good stability and electrocatalytic activity on the reduction of chlorate and bromate ions in aqueous solution. The catalytic process is regarded as an EC mechanism.

INSITU CONDUCTIVITY ELECTROCHEMISTRY OF CONDUCTIVE POLYMERS - POLY(3-METHYLTHIOPHENE) AND POLYTHIOPHENE

In situ monitoring of conductivity and potential response of conductive polymers during electrochemical process had been described. A renewable carbon fibre array ring-glassy carbon disk electrode was used for this purpose. Poly(3-methylthiophene) and polythiophene were investigated with this method, and some 5 orders in magnitude of conductivity changes were observed during the electrochemical redox process.

ELECTROLYTE EFFECTS ON THE ELECTROCHEMICAL POLYMERIZATION OF N-BENZYLANILINE

The electrochemical behaviour of N-benzylaniline polymerization is determined by the nature of the electrolyte. The voltammograms for a poly-N-benzylaniline modified Pt electrode prepared in 1 M HCl (abbreviated to PBAn(HCl)), and 1 M H2SO4 (PBAn(H2SO4)) tested in 1 M hydrochloric, sulfuric, and perchloric acid were almost superimposable. The polymer film electrode prepared in 1 M HClO4 (abbreviated to PBAn(HClO4)) is electroinactive, and exhibits only charging behaviour in 1 M HClO4 solution and can be activated in hydrochloric or other acid electrolytes with a smaller anion. These interesting phenomena are explained in terms of the anions catalyzing the loss of benzyl groups.

LIGHT-ASSISTED OXIDATIVE DOPING OF POLYANILINES

A novel doping phenomenon of fully reduced polyaniline and poly-o-methyl-aniline, "light-assisted oxidative doping", was found for the first time. The doping reaction was followed by FTIR, UV-VIS, ESR and electrical conductivity measurements. It was shown that the fully reduced polyanilines in the form of HCl-salts undergo a spontaneous transition from an insulator or semiconductor to a conductor when exposed to air and light, and their final molecular chain structures are analogous to those found in HCl-doped common polyanilines.

THE INFLUENCE OF PROTONIC ACIDS ON THE CHEMICAL POLYMERIZATION OF ORTHO-METHYLANILINE

The chemical polymerization of ortho-methylaniline (MAn) is performed in aqueous solution of six protonic acids. The MAn polymerization conversion, and the electrical conductivity and doping level as well as molecular chain structure of the polymers obtained depend not only on the acid concentration but also on their acidity and molecular size.