A high speed direct digital frequency synthesizer realized by a segmented nonlinear DAC

This paper presents a high speed ROM-less direct digital frequency synthesizer (DDFS) which has a phase resolution of 32 bits and a magnitude resolution of 10 bits. A 10-bit nonlinear segmented DAC is used in place of the ROM look-up table for phase-to-sine amplitude conversion and the linear DAC in a conventional DDFS.The design procedure for implementing the nonlinear DAC is presented. To ensure high speed, current mode logic (CML) is used. The chip is implemented in Chartered 0.35μm COMS technology with active area of 2.0 × 2.5 mm~2 and total power consumption of 400 mW at a single 3.3 V supply voltage. The maximum operating frequency is 850 MHz at room temperature and 1.0 GHz at 0 ℃.

Design for an IO block array in a tile-based FPGA

A design for an IO block array in a tile-based FPGA is presented.Corresponding with the characteristics of the FPGA, each IO cell is composed of a signal path, local routing pool and configurable input/output buffers.Shared programmable registers in the signal path can be configured for the function of JTAG, without specific boundary scan registers/latches, saving layout area.The local routing pool increases the flexibility of routing and the routability of the whole FPGA.An auxiliary power supply is adopted to increase the performance of the IO buffers at different configured IO standards.The organization of the IO block array is described in an architecture description file, from which the array layout can be accomplished through use of an automated layout assembly tool.This design strategy facilitates the design of FPGAs with different capacities or architectures in an FPGA family series.The bond-out schemes of the same FPGA chip in different packages are also considered.The layout is based on SMIC 0.13μm logic 1P8M salicide 1.2/2.5 V CMOS technology.Our performance is comparable with commercial SRAM-based FPGAs which use a similar process.

A widely tunable continuous-time LPF for a direct conversion DBS tuner

A continuous-time 7th-order Butterworth Gm-C low pass filter (LPF) with on-chip automatic tuning circuit has been implemented for a direct conversion DBS tuner in 0.35μm SiGe BiCMOS technology. The filter's -3 dB cutoff frequency f0 can be tuned from 4 to 40 MHz. A novel on-chip automatic tuning scheme has been successfully realized to tune and lock the filter's cutoff frequency. Measurement results show that the filter has -0.5 dB passband gain, +/- 5% bandwidth accuracy, 30 nV/Hz~(1/2) input referred noise, -3 dBVrms passband IIP3, and 27 dBVrms stopband IIP3. The I/Q LPFs with the tuning circuit draw 13 mA (with f_0 = 20 MHz) from 5 V supply, and occupy 0.5 mm~2.

面向硅基光互连应用的无源光子集成器件研究进展

光互连是突破传统微电子IC性能瓶颈的重要技术手段,对推进"后摩尔时代"微电子技术的发展和高性能计算技术的实现具有关键性意义.本文在归纳总结不同层次光互连结构特点的基础上,对片上光互连(on-chip or intra-chip optical interconnects)所涉及的若干种无源光子集成器件的设计制备及性能特点进行了分析介绍,这些器件包括SOI亚波长光子线波导、SOI光子晶体波导、MMI分束/合束器、微环/微盘谐振腔滤波器、光子晶体微腔耦合滤波器、光子晶体反射镜等,是硅基片上光互连的基本构成单元.本文对这些关键性光子集成器件的国内最新研究进展进行了报道.

A Low Power Dissipation Wide-Band CMOS Frequency Synthesizer for a Dual-Band GPS Receiver

This paper presents a wide tuning range CMOS frequency synthesizer for a dual-band GPS receiver,which has been fabricated in a standard 0.18μm RF CMOS process. With a high Q on-chip inductor, the wide-band VCO shows a tuning range from 2 to 3.6GHz to cover 2.45 and 3.14GHz in case of process corner or temperature variation,with a current consumption varying accordingly from 0.8 to 0.4mA,from a 1.8V supply voltage. Measurement results show that the whole frequency synthesizer consumes very low power of 5.6mW working at L1 band with in-band phase noise less than - 82dBc/Hz and out-of-band phase noise about - ll2dBc/Hz at 1MHz offset from a 3. 142GHz carrier. The performance of the frequency synthesizer meets the requirements of GPS applications very well.

A Compact Direct Digital Frequency Synthesizer for the Rubidium Atomic Frequency Standard

A compact direct digital frequency synthesizer （DDFS） for system-on-chip implementation of the high precision rubidium atomic frequency standard is developed. For small chip size and low power consumption, the phase to sine mapping data is compressed using sine symmetry technique, sine-phase difference technique, quad line approximation technique,and quantization and error read only memory （QE-ROM） technique. The ROM size is reduced by 98% using these techniques. A compact DDFS chip with 32bit phase storage depth and a 10bit on-chip digital to analog converter has been successfully implemented using a standard 0.35μm CMOS process. The core area of the DDFS is 1.6mm^2. It consumes 167mW at 3.3V,and its spurious free dynamic range is 61dB.

A Novel Power Supply Solution of a Passive RFID Transponder

This paper presents a power supply solution for fully integrated passive radio-frequency identification(RFID) transponder IC,which has been implemented in 0.35μm CMOS technology with embedded EEPROM from Chartered Semiconductor.The proposed AC/DC and DC/DC charge pumps can generate stable output for RFID applications with quite low power dissipation and extremely high pumping efficiency.An analytical model of the voltage multiplier,comparison with other charge pumps,simulation results,and chip testing results are presented.

A High Speed, 12-Channel Parallel, Monolithic Integrated CMOS OEIC Receiver

The design and fabrication of a high speed, 12-channel monolithic integrated CMOS optoelectronic integrated circuit(OEIC) receiver are reported.Each channel of the receiver consists of a photodetector,a transimpedance amplifier,and a post-amplifier.The double photodiode structure speeds up the receiver but hinders responsivity.The adoption of active inductors in the TIA circuit extends the-3dB bandwidth to a higher level.The receiver has been realized in a CSMC 0.6μm standard CMOS process.The measured results show that a single channel of the receiver is able to work at bit rates of 0.8～1.4Gb/s. Altogether, the 12-channel OEIC receiver chip can be operated at 15Gb/s.

High Speed VCSEL-Based Parallel Optical Transmission Modules

Design and fabrication of a parallel optical transmitter are reported. The optimized 12 channel parallel optical transmitter,with each channel＇s data rate up to 3Gbit/s,is designed, assembled, and measured. A top-emitting 850nm vertical cavity surface emitting laser（VCSEL） array is adopted as the light source,and the VCSEL chip is directly wire bonded to a 12 channel driver IC. The outputs of the VCSEL array are directly butt coupled into a 12 channel fiber array. Small form factor pluggable （SFP） packaging technology is used in the module to support hot pluggable in application. The performance results of the module are demonstrated. At an operating current of 8mA, an eye diagram at 3Gbit/s is achieved with an optical output of more than 1mW.

A 12bit 300MHz Current-Steering CMOS D/A Converter

The proposed DAC consists of a unit current-cell matrix for 8MSBs and a binary-weighted array for 4LSBs, trading-off between the precision, speed, and size of the chip. In order to ensure the linearity of the DAC, a double Centro symmetric current matrix is designed by the Q2 random walk strategy. To achieve better dynamic performance, a latch is added in front of the current switch to change the input signal, such as its optimal cross-point and voltage level. For a 12bit resolution,the converter reaches an update rate of 300MHz.

Design,Fabrication,and Testing of Single-Side Alignment of 16×0.8nm Arrayed-Waveguide Grating

A novel design of 100GHz-spaced 16channel arrayed-waveguide grating (AWG) based on silica-on-silicon chip is reported.AWG is achieved by adding a Y-branch to the AWG and arranging the input/output channel in a neat row,so the whole configuration can be aligned and packaged using only one fiber-array.This configuration can decrease the device's size,enlarge the minimum radius of curvature,save time on polishing and alignment,and reduce the chip's fabrication cost.

Integrated electroabsorption-modulated DFB laser by using an improved butt-joint method

An improved butt coupling method is used to fabricate an electroabsorption modulator (EAM) monolithically integrated with a distributed feedback (DFB) laser. The obtained electroabsorption-modulated laser (EML) chip with the traditional shallow ridge exhibits very low threshold current of 12 mA, output power of more than 8 mW, and static extinction ratio of -7 dB at the applied bias voltage from 0.5 to -2.0 V.

16-channel 0.35 mu m CMOS/VCSEL optoelectronic devices

We report some investigations on vertical cavity surface emitting laser (VCSEL) arrays and VCSEL based optoelectronic smart photonic multiple chip modules (MCM), consisting of 1 x 16 vertical cavity surface emitting laser array and 16-channel lasers driver 0.35 mum CMOS circuit. The hybrid integrated multiple chip modules based on VCSEL operate at more than 2GHz in -3dB frequency bandwidth.

Hybrid CMOS/VCSEL optoelectronic modules

We report some investigations on vertical cavity surface emitting laser (VCSEL) arrays and VCSEL based optoelectronic smart photonic multiple chip modules (MCM), consisting of 1x16 vertical cavity surface emitting laser array and 16-channel lasers driver 0.35 Pin CMOS circuit. The hybrid integrated multiple chip modules based on VCSEL operate at more than 2GHz in -3dB frequency bandwidth.

Low power design in 100 MHz embedded SRAM

Low power design method is used in a 100MHz embedded SRAM. The embedded SRAM used in a FFT chip is divided into 16 blocks. Two-level decoders are used and only one block can be selected at one time by tristate control circuits, while other blocks are set stand-by. The SRAM cell has been optimized and the cell area has been minimized at the same time.