亚硝化—厌氧氨氧化处理猪场废水研究

猪场废水COD浓度高、氨氮浓度高、悬浮物浓度高，已成为农村面源污染的主要来源，并严重威胁到农村饮用水安全。猪场废水氨氮浓度高、处理难度大，如何采用经济高效的方法，去除氨氮使其达到排放标准，一直是猪场废水处理中面临的重要难题。 厌氧氨氧化是近年受到国内外水处理研究者广泛关注的新型生物脱氮技术，具有不需要外加有机碳源、节省供氧量、降低能耗等优点。虽然国内外研究者对厌氧氨氧化过程的脱氮机理、厌氧氨氧化菌的生理生化特性等进行了多方面的研究，但已有的报道大多以模拟废水为研究对象，以猪场废水为研究对象的报道，在国内外文献中极少有报导。 本论文以猪场废水为主要研究对象，考察了猪场废水的亚硝化过程、厌氧氨氧化的启动过程，并对亚硝化和厌氧氨氧化联合用于猪场废水脱氮进行了探索。 1．论文首先研究了猪场废水的亚硝化过程，考察了废水水质和主要运行条件对亚硝化过程的影响。实验表明：（1）亚硝化阶段反应时间为8到10h时，出水中氨氮和亚硝酸盐浓度比可达到1：1～1：1.23，满足厌氧氨氧化反应对二者比例的要求；达到前述要求时，氨氮去除率达到58.3～65.6 %，亚硝化率在整个过程均保持在97 %以上，COD去除率在59.2～68.6 %；（2）曝气量（溶解氧）对亚硝化过程影响显著，随着曝气量增大，达到厌氧氨氧化要求的氨氮与亚硝酸盐氮浓度比例所需水力停留时间τ越短，pH出现明显下降的时间越短；（3）τ对应的pH在7.8～8.1之间，无需进行pH调节即可满足厌氧氨氧化反应对pH的要求；（4）氨氮和COD降解过程遵循一级反应动力学，氨氮和COD降解的速率常数分别为0.0656～0.0724 1/h和0.0491～0.0664 1/h。 2．在进行亚硝化过程研究的同时，以模拟废水为试验对象，进行厌氧氨氧化启动研究。以反硝化污泥和养殖厂储水池厌氧底泥的混合污泥作为接种污泥，历时大约100天，培育出具有厌氧氨氧化活性的污泥，氨氮和亚硝酸盐氮最高进水浓度分别为223.8 mg/L和171.4 mg/L，去除率最高分别达48%和41.5%，此时二者消耗比例为1.33：1。 3．在猪场废水的亚硝化研究完成和厌氧氨氧化过程初步启动成功后，在模拟废水中逐步加入猪场废水的亚硝化处理出水，逐步实现亚硝化和厌氧氨氧化的组合。亚硝化出水添加到厌氧反应器后，厌氧氨氧化反应仍可继续进行，且去除效率逐步提高。研究发现添加的亚硝化出水中携带的亚硝化细菌在厌氧氨氧化菌膜外层生长并累积，增加了厌氧氨氧化反应基质的传质阻力，妨碍了厌氧氨氧化效率的提高。 4．亚硝化－厌氧氨氧化实际工程应用探索中，生物接触氧化池可在有效去除废水中的有机物的同时实现亚硝化，出水中氨氮和亚硝酸盐比例平均为1.10，可满足后续厌氧氨氧化的要求；在适宜的进水浓度和温度下，ABR池出现了厌氧氨氧化启动的迹象；研究同时发现，水质的波动和气温的变化是工程中影响厌氧氨氧化菌活性的重要因素。 论文的主要创新点在于：（1）以猪场废水为研究对象，以实现厌氧氨氧化为目标，对亚硝化过程进行了比较详细的考察，获得了亚硝化出水满足厌氧氨氧化要求的工艺条件，通过对其COD和氨氮降解过程的考察，得出亚硝化阶段COD降解和氨氮去除的动力学模型；（2）对亚硝化－厌氧氨氧化处理猪场废水进行了探索，确立了影响其污染物去除率稳定的重要因素。 论文的上述研究成果，为厌氧氨氧化技术的实用性研究提供理论依据。 Piggery wastewater, which is characterized by high concentration of COD、ammonium and suspend substance, has become a most important source of non-point source pollution and also severely threats drinking water security in rural area. How to discharge piggery wastewater with the ammonium concentration meeting standard by economical and effective method? This is the most urgent problem in piggery wastewater treatment. As a new biological nitrogen removal technology, Anammox process has been paid more and more attention by researchers all over the world. Anammox has advantages of no need of organic carbon addition, low oxygen consumption and energy consumption. Plenty of investigations have been carried out to the mechanism, physiological and biochemical characteristic of bacteria about Anammox. Most of researches focused on synthetic wastewater, there is rare report about its application in piggery wastewater. In this paper，experimental studies were performed to investigate Sharon process in treatment of piggery wastewater，the start up process of Annammox using synthetic wastewater were studied, the feasibility of applying Sharon-Anammox process in the nitrogen removal of piggery wastewater was evaluated. 1. Sharon process of piggery wastewater was firstly investigated to analyze the effects of water quality and main running parameters, which meet the NH4+-N to NO2--N ratio requirement of successive Anammox. Results showed: (1)During Sharon Process，after 8～10 hours’ reaction the NH4+-N to NO2--N ratio in effluent reached 1:1.0～1:1.23, when the removal percentage of NH4+-N was 58.3～65.6 %, a semi-nitration rate of above 97 % was achieved during the process; meanwhile 59.2～68.6 % of the COD was also removed. (2)The aeration rate（oxygen） had obvious effect on the hydraulic retention time(τ) which met the NH4+-N to NO2--N ratio requirement of Anammox. As aeration rate increased, the hydraulic retention time(τ) was shortened. (3) The pH corresponding to τ was between 7.8 and 8.1, thus it needed no artificial adjustment. (4) The reduction of ammonia and COD followed the first-order reaction kinetics. The velocity constants of ammonia and COD were 0.0656～0.0724 1/h and 0.0491～0.0664 1/h, respectively. 2. The startup of Anammox process using the artificial wastewater was performed simultaneously with Sharon. The aim was to investigate the running parameters of Anammox and make foundation for the combination stage. By using the mixture of denitrifying sludge and anaerobic sludge in tank of the breeding factory, sludge of Anammox activity was cultivated in UASB after 100 days. The removal percentage of NH4+-N and NO2-N were up to 48% and 41.5%, respectively, when the NH4+-N and NO2-N influent concentration were 223.8 mg/L and 171.4 mg/L, respectively, the NH4+-N and NO2-N removal rate was 1.33:1. 3. After investigation of Sharon and startup of Anammox, effluent of Sharon process was added into the synthetic wastewater to combine Sharon and Anammox step by step. It took some time after the addition of Sharon effluent that Anammox reaction continued and the removal rate kept increasing. It indicated that nitrifying bacteria were carried by the Sharon effluent cumulated in the outer layer of Anammox. This enhanced transfer resistance of Anammox reaction and the increasing removal rate was restrained. 4. In the bio-contact oxidation pond of practical project, Sharon process were carried out successfully and organic compounds were removed effectively. An average NO2-N/ NH4+-N rate of 1:1.0 was achieved in the effluent, which met the requirement of successive Anammox. Under condition of suitable influent concentration and temperature, there was evidence that Anammox could start up in ABR. The variety of wastewater and temperature had great affects on Anammox activity in practical engineering. Innovation of this paper: (1) The Sharon process for treating piggery wastewater was discussed in details. Technological parameters that met requirement of Anammox were obtained. The dynamic models of COD and ammonium removal in the process were educed. (2) Sharon-Ananmmox for treatment of piggery wastewater was investigated, and the primary influencing factors was studied. This paper could be a theoretical consult for research of Anammox utility.

猪场废水短程硝化反硝化-厌氧氨氧化脱氮研究

畜禽废水是农村水环境污染的主要来源之一，其处理的难点在于脱氮。传统生物脱氮法具有能耗高、需大量外加碳源等缺点，开发低成本、高效率的新型生物脱氮技术具有重要意义。 本研究将短程硝化反硝化和厌氧氨氧化两种脱氮新技术结合，让前者为后者创造去除可降解COD、降低总氮负荷、调整pH、调整氨氮和亚硝酸盐氮浓度比例等进水条件，而后者可在无需外加碳源的条件下进一步脱氮，二者结合可成为高氨氮、低C/N废水脱氮的新途径。 试验以低碳氮比猪场废水为研究对象，首先进行了短程硝化反硝化预处理研究，同时启动并运行调控厌氧氨氧化反应器，最后以经过短程硝化反硝化预处理的猪场废水为进水，进行厌氧氨氧化脱氮考察。实验表明：（1）短程硝化反硝化作为厌氧氨氧化的预处理工序是可行的。猪场废水通过短程硝化反硝化，可以达到基本去除可生化COD、部分脱氮、控制出水氨氮和亚硝酸盐氮浓度之比在1︰1左右、pH在7.5～8.0的目的， COD和总氮平均去除率分别为64.3%、49.1%,出水可达到厌氧氨氧化反应的进水要求。（2）采用模拟废水启动厌氧氨氧化反应器，经过5个月左右的运行调控，反应器启动成功并稳定运行，最高总氮去除率为87.1%，总氮容积去除率最高达到0.14kg/m3.d；整个稳定阶段，氨氮、亚硝酸盐氮、硝酸盐氮的变化量之比为1︰1.21︰0.33。（3）经过短程硝化反硝化预处理的猪场废水厌氧氨氧化脱氮效果稳定，氨氮、亚硝酸盐氮、总氮、COD的平均去除率分别为93.0%、99.4%、84.6%、18.1%，处理效果与模拟废水处理系统相比无明显变化。（4）经过短程硝化反硝化预处理后，猪场废水中残留有机物成分在厌氧氨氧化反应过程中无显著变化，主要为酯类和烷烃类物质；残留有机物对厌氧氨氧化效果无明显影响。（5）采用PCR技术进行特殊功能菌种检测，结果表明模拟废水处理系统和猪场废水处理系统的菌群中均含有厌氧氨氧化菌和好氧硝化菌；通过blast比对，厌氧氨氧化菌扩增序列与未培养的Planctomycetales菌和Candidatus Brocadia fulgida菌16S rRNA部分序列相似性分别为95％、90%。（6）MPN法菌种计数结果显示，模拟废水处理系统和猪场废水处理系统的菌群中均含有硝化细菌、亚硝化细菌和少量反硝化菌，实验条件下的微生物系统是一个厌氧氨氧化菌与好氧硝化菌、反硝化菌共存的系统。 Poultry wastewater is one of the main source of water pollution in rural areas，and nitrogen removal is the most difficult part in treating poultry wastewater. There are some disadvantages in traditional nitrogen removal, such as high energy consumption and more additional organic carbon. It is important to develop ecolomical and efficient technologyies. Shortcut nitricfication/denitrification, as a pretreatment process, was combined with Anammox in this research, so that part of total nitrogen and most degradable COD could be removed by the former, and further nitrogen removal could be implemented by the latter. The combination of the two technologies was a new approach to treat wastewater with high ammonium and low C/N. Piggery wastewater with low C/N was treated in lab-scale experiment. Firstly, shortcut nitrification/denitrification was investigated, and Anammox reactor was started up successfully at the same time. Then piggery wastewater after pretreatment was treated by Anammox. The results showed :(1) It was feasible to take nitrification/denitrification as the pretreatment process of Anammox. By using this process, part of total nitrogen and COD were removed, the ratio of ammonium and nitrite reached around 1︰1 and the pH was about 7.8, which were favorable for Anammox. The average removal percentage of COD and total nitrogen were about 64.3% and 49.1%, respectively. (2) Simulated wastewater was used to start up Anammox reactor. The reactor was started up successfully within 5 months and stable performance was achieved. The highest nitrogen removal reached 87.1% and the biggest volumetric total nitrogen removal rate reached 0.14kg/m3.d. The average ratio of ammonium, nitrite and nitrate was 1:1.21:0.33. (3)Taking the effluent of shortcut nitrification/denitrification as the influent, the nitrogen removal efficiency of Anammox was stable, and the the average removal percentage of ammonium, nitrite, total nitrogen and COD were 93.0%, 99.4% , 84.6% and 18.1%, respectively, which had little difference with that by using simulated wastewater..(4) After pretreatment, the residual organic carbon in piggery wastewater showed no obvious change during the Anammox process, and the main organic compounds were saturated hydrocarbon and ester, which had no obvious negative effect on Anammox process.(5) By PCR technology, the existence of Anammox bacteria was confirmed and the aerobic nitrifying bacteria was found to coexist as well. The result of blast showed that the identities of Anammox bacterium to part of 16S rRNA sequence of uncultured Planctomycetales bacterium and Candidatus Brocadia fulgida bacterium were 95% and 90%, respectively.（6）By MPN method, nitrite oxidizer, ammonium oxidizer and denitrification bacteria were detected in both simulated and piggery wastewater treatment system of Anammox, and the microorganism system was composed of Anammox bacteria，aerobic bacteria and denitrification bacteria together.

Impact Parameter Dependence of Double Neutron/Proton Ratio of Nucleon Emissions in Isotopic Reaction Systems

Within the transport model IBUU04, we investigate the double neutron/proton ratio of free nucleons taken from two reaction systems using two Sn isotopes at the beam energy of 50MeV/nucleon and with the impact parameters 2 fm, 4 fm and 8 fm, respectively. It is found that the double neutron/proton ratio from peripheral collisions is more sensitive to the density dependence of the symmetry energy than those from mid-central and central collisions.

Clay ratio as a tracer to assess the origin of soil-derived dust

IEECAS SKLLQG

Systematic study of the pi(-)/pi(+) ratio in heavy-ion collisions with the same neutron/proton ratio but different masses

A systematic study of the pi(-)/pi(+) ratio in heavy-ion collisions with the same neutron/proton ratio but different masses can help single out effects of the nuclear mean field on pion production. Based on simulations using the IBUU04 transport model, it is found that the pi(-)/pi(+) ratio in head-on collisions of Ca-48 + Ca-48, Sn-124 + Sn-124, and Au-197 + Au-197 at beam energies from 0.25 to 0.6 GeV/nucleon increases with increasing the system size or decreasing the beam energies. A comprehensive analysis of the dynamical isospin fractionation and the pi(-)/pi(+) ratio as well as their time evolution and spatial distributions demonstrates clearly that the pi(-)/pi(+) ratio is an effective probe of the high-density behavior of the nuclear symmetry energy.

Baryon magnetic moment and beta decay ratio in colored quark cluster model

Baryon magnetic moments of p, n, Sigma(+), Sigma(-), Xi(0), Xi(-) and the beta decay ratios (G(A)/G(V)) of n -> p, Sigma(-) -> n and Xi(0) -> Sigma(+) are calculated in a colored quark cluster model. With SU(3) breaking, the model gives a good fit to the experimental values of those baryon magnetic moments and the beta decay ratios. Our results show that the orbital motion has a significant contribution to the spin and magnetic moments of those baryons and the strange component. in nucleon is small.

Entrance-channel dependence of isospin effects on double n/p ratio in HIC

Within the hadronic transport model IBUU04, we investigate the effect of density-dependent symmetry energy on double neutron/proton (n/p) ratio of free nucleons in heavy ion collisions by taking four isotopic Sn+Sn reaction systems. Especially the entrance-channel asymmetry and impact-parameter dependence of the effect of symmetry energy are discussed. It is found that in both central and semi-central collisions the sensitivity of the double n/p ratio to the density-dependent symmetry energy is more pronounced in neutron-richer systems. Our results also indicate clearly that the effect of symmetry energy is stronger in central collisions than that in semi-central collisions.

Probing the high density behavior of the symmetry energy by using the free neutron-proton ratio

Based on the isospin- and momentum-dependent transport model IBUU04, the transverse momentum distributions of the free neutron-proton ratio in the Sn-132+(124) Sn reaction system at mid-central collisions with beam energies of 400/A MeV, 600/A MeV and 800/A MeV are studied by using two different symmetry energies. It is found that the free neutron-proton ratio as a function of the transverse momentum at the mid-rapidity is very sensitive to the density dependency of the symmetry energy especially at incident energies around 400/AMeV.

The neutron/proton ratio of squeezed-out nucleons and the high density behavior of the nuclear symmetry energy

Within a transport model it is shown that the neutron/proton ratio of squeezed-out nucleons perpendicular to the reaction plane, especially at high transverse momenta, in heavy-ion reactions induced by high energy neutron-rich nuclei can be a useful tool for studying the high density behavior of the nuclear symmetry energy.

Beam energy dependence of the pi(-)/pi(+) ratio

Using the isopin- and momentum-dependant hadronic transport model IBUU04, the effect of symmetry energy on the pi(-)/pi(+) ratio are studied. Our investigations are based on the calculations of the Sn-132+Sn-124 semi-central collisions at beam energies of 400/ A MwV, 600/ A MeV and 800MeV. It is found that both the transverse momentum and kinetic energy distributions of the pi(-)/pi(+) ratio are rather sensitive to the symmetry energy, especially around the Colomb peaks. The position of the coulomb peak is shown to be nearly indrpendant of beam energy. The sesitivity of the pi(-)/pi(+) ratio to the symmetry ebergy decreases as the beam energy increases from 600/ A MeV to 800/ A MeV.