Interfacial activity of sec-nonylphenoxy acetic acid and kinetics of yttrium extraction

The interfacial behavior of sec-nonylphenoxy acetic acid (CA-100) at various diluents/(H, Na)Cl interfaces was examined using the Du Nouy ring method. Different adsorption isotherms such as the Gibbs and Szyszkowski were in good agreement with the experimental data. The values of interfacial excess at saturated interface increase in the following order: n-heptane > kerosene > cyclohexane > CCl4 > toluene > benzene > chloroform. The effects of temperature, acidity, and ionic strength of the aqueous phase on the interfacial activity of CA- 100 were also examined. The interfacial-activity data were used to discuss the mechanism and kinetics of yttrium (Y) extraction.

Separation of scandium, yttrium and lanthanum in high-performance centrifugal partition chromatography with S-octyl phenyloxy acetic acid

Separation of scandium(III), yttrium(III) and lanthanum(III) was performed by high-performance centrifugal partition chromatography (HPCPC) employing the stationary phase of S-octyl phenyloxy acetic acid (CA-12). The liquid-liquid extraction behavior of CA-12 for Sc(III), Y(III) and La(III), the acidity of aqueous phase, and the operation conditions of HPCPC were examined. The retention volume (V-R) increased with the order of Y(III), La(III) and Sc(III) accompanied with the elution of the mobile phase in different pH, which is lowered from 4.6 to 2.1.

Copolymerization of CO2 and propylene oxide under rare earth ternary catalyst: design of ligand in yttrium complex

Copolymerization of carbon dioxide and propylene oxide was carried out employing (RC6H4COO)(3)Y/glycerin/ZnEt2 (R = -H, -CH3, NO2, -OH) ternary catalyst systems. The feature of yttrium carboxylates (ligand, substituent and its position on the aromatic ring) is of great importance in the final copolymerization. Appropriate design of substituent and position of the ligand in benzoate-based yttrium complex can adjust the microstructure of aliphatic polycarbonate in a moderate degree, where the head-to-tail linkage in the copolymer is adjustable from 68.4 to 75.4%. The steric factor of the ligand in the yttrium complex is crucial for the molecular weight distribution of the copolymer, probably due to the fact that the substituent at 2 and 4-position would disturb the coordination or insertion of the monomer, lead the copolymer with broad molecular distribution. Based on the study of ultraviolet-visible spectra of the ternary catalyst in various solvents, it seems that the absorption band at 240-255 nm be closely related to the active species of the rare earth ternary catalysts.

Solvent extraction of scandium(III), yttrium(III), lanthanides(III), and divalent metal ions with sec-nonylphenoxy acetic acid

Such physicochemical properties of sec-nonylphenoxy acetic acid (CA-100) as the solubility in water, acid dissociation constant in water, dimerization constant in heptane, and distribution constant in organic solvent-water were measured by two-phase titration. The extraction behaviors of scandium (III), yttrium (III), lanthanides (III), and divalent metal ions from hydrochloric acid solutions with CA-100 in heptane have been investigated, and the possibilities of separating scandium (yttrium) from lanthanides and divalent metal ions have been carefully discussed. The stoichiometries of the extracted metal complexes were investigated by the slope-analysis technique. The effect of the nature of diluent on the extraction of yttrium (III) with CA100 has been studied and correlated with the dielectric constant.

Preparation of W-Al alloys by mechanical alloying

W1-xAlx (x=0-0.86) alloys were synthesized by mechanically alloying the pure metal powder mixtures at designated compositions by conventional high-energy ball milling. The W-Al alloys were stable under high pressure and high temperature. The alloys were lighter than W. The hardness and oxidation resistance of the alloys was greatly improved compared to both W and Al. (C) 2002 Elsevier Science B.V. All rights reserved.

Preparation and characterization of ordered yttrium arachidate multilayer

The behavior of arachidic acid on the surface of YCI3 aqueous subphase was studied by LB and Brewster angle microscopy techniques. The results showed that the pre-compressing time and the pH of the subphase played an important role in the forming of the monolayer. The monolayer on the subphase surface was irreversible. If the monolayer was compressed into wrinkles, the monolayer could not become uniform again. The optimum transferring conditions were selected and the ordered yttrium arachidate multilayer with a long spacing of 4.96 nm and a tilt angle of 28.5degrees of the three alkyl chains from the surface normal was fabricated and characterized.

Synthesis and luminescence properties of oxyapatite NaY9Si6O26 doped with Eu3+, Tb3+, Dy3+ and Pb2+

Oxyapatite NaY9Si6O26 was prepared by sol-gel method. By choosing the precursors, a single phase compound was obtained. This soft chemical method lowered the reaction temperature by 100degreesC compared with the solid state method. Its morphology was studied by transmission electron microscopy (TEM). Several rare earth ions (Eu3+, Tb3+, Dy3+) and Pb2+ ion were doped in this compound. The high resolution emission spectrum of Eu3+ showed that rare earth ions occupied two yttrium sites. In spite of the charge imbalance of Pb2+ with the cations in this compound, it was found that Pb2+ could emit in UV range and transfer its excitation energy to Dy3+ ion.

Electrochemical characteristic of LaNi-based hydrogen storage alloys

Effect of purity of alloy components on the electrode performance of LaNi2 alloys was investigated. The results showed the purity of components had less effect on discharge capacity and self-discharge of LaNi2 alloys. Partial substitution of Al or Mn for Ni greatly improved discharge properties of LaNi2-xAlx, or LaNi2-yMny alloys as negative electrodes in MFl-Ni battery, 0.15less than or equal toxless than or equal to0.25; 0.15less than or equal toyless than or equal to0.25. In addition, surface treatment of LaNi1.8Al0.2 alloy electrode was performed by polymerizing cis-butenedioate with Co-60- gamma -ray radiation, which. had better affect on self-discharge and cycle life of the alloy electrodes at low temperature(-28 C-degrees).

Prediction of molar absorptivities of color reagents and their color reactions with yttrium by artificial neural networks

The new topological indices A(x1)-A(x3) suggested in our laboratories were applied to the study of structure-property relationships between color reagents and their color reactions with yttrium. The topological indices of twenty asymmetrical phosphone bisazo derivatives of chromotropic acid were calculated. The work shows that QSPR can be used as a novel aid to predict the molar absorptivities of color reactions and in the long term to be helpful tool in-color reagent design. Multiple regression analysis and neural network were employed simultaneously in this study. The results demonstrated the feasibility and the effectiveness of the method.

Binary alloys of nylon 1010 and ethylene-propylene copolymer: Chemical, morphological, and mechanical analysis

The modification of ethylene-propylene copolymer (EPM) has been accomplished by melt grafting of maleic anhydride (MAH) molecules promoted by radical initiators. The resulting EPM-g-MAH and EPM have been used to obtain binary nylon 1010/EPM or nylon 1010/EPM-g-MAH blends by melt mixing. It was found that the EPM-g-MAH copolymer used as the second component has a profound effect upon the properties of the resulting blends. This behavior has been attributed to a series of chemical and physicochemical interactions taking place between the two components. The interactions are due to the presence of the anhydride functionality on the copolymer and do not occur when this functionality is absent. The interaction has been confirmed by Fourier-transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, and scanning electron microscopic.

Rheological properties and crystallization behavior of yttrium oxide filled low ethylene content polypropylene copolymer

The rheological properties and crystallization characteristics of low ethylene content poly propylene (EPM) with and without Yittrium oxide (Y2O3) as a filler was investigated by cone-plate viscometer and differential scanning calorimetry. Yittrium oxide had a profound effect on the viscosities of the systems. To determine the nonisothermal crystallization rate of the materials, a new estimation method was used. From the results, we can conclude that Y2O3 acts as a nucleating agent, which increased the crystallization rate of the EPM. (C) 1996 John Wiley & Sons, Inc.

Sol-gel synthesis and luminescence of Y4Al2O9:RE3+(RE=Eu, Tb)

Y4Al2O9 (YAM) was prepared by a sol-gel process, using yttrium and aluminum citrate complexes as precursors. The sol-gel process produced single-phase YAM at 900 degrees C, as opposed to the conventional solid-state reaction, which led to the formation of other phases, even if at 1600 degrees C. The emission and excitation spectra of Eu3+ and Tb3+ in YAM showed the existence of two luminescence centers, agreeing with the crystal structure of YAM. The spectral properties of the samples are discussed.

Study on structure-property relationships between color reagents and sensitivity of color reactions with yttrium by topological indices

In this paper, three topological indices, Am-1, Am-2, and Am-3, multivariate analysis in structure-property studies. The topological indices of twenty asymmetrical phosphosphono bisazo derivatives of chromotropic acid have been calculated. The structure-property relationships between color reagents and molar absorptivity of color reactions with yttrium have been studied by A(m) indices and structure selective factors. Good results have been obtained by using correlation equation to predict the molar absorptivity of new color reagents.