Tuning the Energy Level of Organic Sensitizers for High-Performance Dye-Sensitized Solar Cells

Cost-effective organic sensitizers will play a pivotal role in the future large-scale production and application of dye-sensitized solar cells. Here we report two new organic D-pi-A dyes featuring electron-rich 3,4-ethylenedioxythiophene- and 2,2'-bis(3,4-ethylenedioxythiophene)-conjugated linkers, showing a remarkable red-shifting of photocurrent action spectra compared with their thiophene and bithiophene counterparts. On the basis of the 3-f{5'-[N,N-bis(9,9-dimethylfluorene-2-yl)phenyl]-2,2'-bis(3,4-ethylenedioxythiophene)-5-yl}2-cyanoacrylic acid dye, we have set a new efficiency record of 7.6% for solvent-free dye-sensitized solar cells based on metal-free organic sensitizers. Importantly, the cell exhibits an excellent stability, keeping over 92% of its initial efficiency after 1000 h accelerated tests under full sunlight soaking at 60 degrees C. This achievement will considerably encourage further design and exploration of metal-free organic dyes for higher performance dye-sensitized solar cells.

An Extremely High Molar Extinction Coefficient Ruthenium Sensitizer in Dye-Sensitized Solar Cells: The Effects of pi-Conjugation Extension

We report a heteroleptic ruthenium complex (007) featuring the electron-rich 5-octyl-2,2'-bis(3,4-ethylenedioxythiophene) moiety conjugated with 2,2-bipyridine and exhibiting 10.7% power conversion efficiency measured at the AM1.5G conditions, thanks to the enhanced light-harvesting that is closely related to photocurrent. This C107 sensitizer has an extremely high molar extinction coefficient,of 27.4 x 10(3) M-1 cm(-1) at 559 nm in comparison to its analogue C103 (20.5 x 10(3) M-1 cm(-1) at 550 nm) or Z907 (12.2 x 10(3) M(-1)cm(-1) at 521 nm) with the corresponding 5-hexyl-3,4-ethylenedioxythiopliene- or nonyl-substituted bipyridyl unit. The augmentation of molar extinction coefficients and the bathochromic shift of low-energy absorption peaks along with the pi-conjugation extension are detailed by TD-DFT calculations. The absorptivity of mesoporous titania films grafted with Z907, C103, or C107 sublinearly increases with the molar extinction coefficient of sensitizers, which is consistent with the finding derived from the surface coverage measurements that the packing density of those sensitizers decreases with the geometric enlargement of ancillary ligands.

White electroluminescence from polyfluorene chemically doped with 1,8-napthalimide moieties

An efficient white light-emitting polymer was developed with blue polyfluorene (PFO) chemically doped with orange fluorescent 1, 8-naphthalimide moieties. The emission spectrum can be easily tuned by varying the content of 1, 8-naphthalimide moieties. A white polymeric light-emitting diode (WPLED) with a structure of indium tin oxide (ITO)/the complex of (3,4-ethylenedioxythiophene) and polystyrene sulfonic acid (PEDOT)/polymer/Ca/Al showed a current efficiency of 5.3 cd/A and a power efficiency of 2.8 Lm/W at 6 V with the Commission Internationale de L'Eclairage (CIE) coordinates at (0.25,0.35). Moreover, the WPLED from the copolymer showed a very stable white light emission at different driving voltage and brightness. The CIE coordinates of the WPLED were (0.25, 0.35), (0.26, O.36), and (0.26, 0.36) under driving voltages of 6, 8, and 10 V, corresponding to the brightness of 82, 3555, and 7530 cd/m(2), respectively. This approach for realization of white light emission is promising over the polymer blending system in terms of both efficiency and color stability.

Highly efficient green-emitting phosphorescent iridium dendrimers based on carbazole dendrons

Green-emitting iridium dendrimers with rigid hole-transporting carbazole dendrons are designed, synthesized, and investigated. With second-generation dendrons, the photoluminescence quantum yield of the dendrimers is up to 87% in solution and 45% in a film. High-quality films of the dendrimers are fabricated by spin-coating, producing highly efficient. non-doped electrophosphorescent organic light-ernitting diodes (OLEDs). With a device structure of indium tin oxide/poly(3,4-ethylenedioxythiopheiie):poly(styrene sulfonic acid)/neat dendrimer/1,3,5-tris(2-N-phenylbenzimidazolyl)benzene/LiF/Al, a maximum external quantum efficiency (EQE) of 10.3% and a maximum luminous efficiency of 34.7 cd A(-1) are realized. By doping the dendrimers into a carbazole-based host, the maximum EQE can be further increased to 16.6%. The integration of rigid hole-transporting dendrons and phosphorescent complexes provides a new route to design highly efficient solution-processable dendrimers for OLED applications.

Highly efficient pure-white-light-emitting diodes from a single polymer: Polyfluorene with naphthalimide moieties

Light-emitting diodes exhibiting efficient pure-white-light electroluminescence have been successfully developed by using a single polymer: polyfluorene derivatives with 1,8-naphthalimide chromophores chemically doped onto the polyfluorene backbones. By adjusting the emission wavelength of the 1,8-naphthalimide components and optimizing the relative content of 1,8-naphthalimide derivatives in the resulting polymers, white-light electroluminescence from a single polymer, as opposed to a polymer blend, has been obtained in a device with a configuration of indium tin oxide/poly(3,4-ethyleiledioxythiophene)(50 nm)/polymer(80 nm)/Ca(10 nm)/Al(100 nm). The device exhibits Commission Internationale de I'Eclairage coordinates of (0.32,0.36), a maximum brightness of 11900 cd m(-2), a current efficiency of 3.8 cd A(-1), a power efficiency of 2.0 lm W-1. an external quantum efficiency of 1.50 %, and quite stable color coordinates at different driving voltages, even at high luminances of over 5000 cd m(-2).

Synthesis of isomeric bis(amine anhydride)s for novel poly(amine imide)s by Pd-catalyzed amination of 4-chlorophthalic anhydride

Two novel bis(amine anhydride) monomers, N,N'-bis(3,4-dicarboxyphenyl)-1,4-phenylenediamine dianhydride I and N,/N'-bis(3,4-dicarboxyphenyl)-1,3-phenylenediamine dianhydride 11, were prepared via palladium-catalyzed amination reaction of 4-chloro-N-methylphthaliniide with 1,4-phenylenediamine or 1,3-phenylenediamine, followed by alkaline hydrolysis of the intermediate bis(amine imide)s and subsequent dehydration of the resulting tetraacids. A series of new poly(amine imide)s were prepared from the synthesized dianhydride monomers with various diamines in NMP via conventional two-step method.

Synthesis of bis(amine anhydride)s for novel high T(g)s and organosoluble poly(amine imide)s by palladium-catalyzed amination of 4-chlorophthalide anhydride

Two novel bis(amine anhydride)s, NN-bis(3,4-dicarboxyphenyl)aniline dianhydride (I) and N,N-bis(3,4-dicarboxyphenyl)-p-tert-butylaniline (II), were synthesized from the palladium-catalyzed amination reaction of N-methyl-protected 4-chlorophthalic anhydride with arylamines, followed by alkaline hydrolysis of the intermediate bis(amine-phthalimide)s and subsequent dehydration of the resulting tetraacids. The X-ray structures of anhydride I and II were determined. The obtained dianhydride monomers were reacted with various aromatic diamines to produce a series of novel polyimides. Because of the incorporation of bulky, propeller-shaped triphenylamine units along the polymer backbone, all polyimides exhibited good solubility in many aprotic solvents while maintaining their high thermal properties. These polymers had glass transition temperatures in the range of 298-408 degrees C. Thermogravimetric analysis showed that all polymers were stable, with 10% weight loss recorded above 525 degrees C in nitrogen.The tough polymer films, obtained by casting from solution, had tensile strength, elongation at break, and tensile modulus values in the range of 95-164 MPa, 8.8-15.7%, and 1.3-2.2 GPa, respectively.

Characterization and properties of biodegradable poly(hydroxyalkanoates) and 4,4-dihydroxydiphenylpropane blends: Intermolecular hydrogen bonds, miscibility and crystallization

Intermolecular hydrogen bonds, miscibility, crystallization and thermal stability of the blends of biodegradable poly(3-hydroxybutyrate) (PHB), poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) [P(3HB-3HHx)] with 4,4-dihydroxydiphenylpropane (DOH2) were investigated by FTIR, C-13 Solid state NMR, DSC, WAXD and TGA. Intermolecular hydrogen bonds were found in both blend systems, which resulted from the carbonyl groups in the amorphous phase of both polyesters and the hydroxyl groups of DOH2. The intermolecular interaction between P(3HB-3HHx) and DOH2 is weaker than that between PHB and DOH2 owing to the steric hindrance of longer 3HHx side chains. Because of the effect of the hydrogen bonds, the chain mobility of both PHB and P(3HB-3HHx) components was limited after blending with DOH2 molecules. Single glass transition temperature depending on the composition was observed in all blends, indicating that those blends were miscible in the melt. The addition of DOH2 suppressed the crystallization of PHB and P(3HB-3HHx) components. Moreover, the crystallinity of PHB and P(3HB-3HHx) components also decreased with increasing DOH2 content in the blends.

聚3—羟基丁酸酯与聚丙撑碳酸酯共混体系研究

本论文对完全生物降解聚（3—羟基丁酸酯）（PHB）和聚丙撑碳酸酯（PPC）共混体系进行了全面研究，目的是提高PHB的综合性能，加深对共混高聚物的基本物理问题的认识，进一步明晰高聚物的结构和性能之间的关系.1.在分析判断PPC的热降解机理的基础上，对PPC进行了封端处理，阻止了以端羟基回咬“解拉链”方式引起的热降解，增加了PPC热降解反应活化能，显著地提高了PPC的稳定性（提高30K以上）.2.经热性能和形态结构等方面的表征，PHB/PPC共混体系为不相容体系，直接在PHB中加入PPC不能改善PHB的韧性和其它力学性能.3.PCL-PEG-PCL嵌段共聚物能够作为PHB/PPC的增容剂，在PHB/PPC共混体系中加入PCL-PEG-PCL三嵌段共聚物能显著减小分散相的平均尺寸.4.选用增塑剂对PPC进行增塑能够在很大范围内（80K）调节PPC的玻璃化转变温度，使PPC表现出弹性体的特性，拓宽了PPC的应用范围.5.增塑剂1,2丙二醇碳酸酯（PGC）对PHB有一定的增塑作用，但不能明显改善PHB的力学性能.6.增塑后的PPC是PHB的良好增韧剂，使PHB由脆性断裂转变为韧性断裂，最佳增韧效果可使PHB的抗冲击强度由36J/m增加到70PHB/30PPC/20PGC的307J/m，增加8倍.7.增塑后的PPC能够实现对PHB增韧，是增塑剂使得PPC在冲击实验条件下仍然保持弹性体的性质，由此引发空洞化、多重银纹和剪切屈服共存的增韧方式提高PHB的性能.

聚（3-羟基烷酸酯）的改性研究

该论文目的是改性细菌合成的聚(3-羟基丁酸酯)(PHB)及其共聚物(PHBV),采用交联或共混的方法,改变其聚集态结构或超分子结构,从而改善其力学性能.加深对高聚物结构与性能之间关系,高聚物结晶规律、及特殊相互作用在高聚物中作用的认识.1.采用反应性加工,用过氧化二异丙苯(DCP)引发PHBV的自由基链转移反应,产生了支化和交联的化学结构.2.用交联助剂二苯甲撑双马来酰亚胺(BMI)实现了PHBV的γ-辐射交联.交联的PHBV熔点和结晶度下降.3.双酚A(BPA)在PHBV/BPA共混物中起到了物理交联剂的作用.4.氢键交联结构使PHBV的链段运动受限,结晶速率下降.5.对叔丁基苯酚(TBP)在PHBV中形成了氢键接枝的超分子结构.6.经过溶液共混,BPA在PHB中起到了物理交联剂的作用,使PHB的断裂伸长率从3%提高到45%.8.二醋酸纤维素(CDA)与PHBV经溶液共混(混合溶剂氯仿/丙酮),PHBV的力学性能没有改善,原因可能是CDA-PHBV分子间的氢键作用较弱,组分间发生严重相分离,不利于性能提高.

聚3-羟基烷酸酯异相成核结晶的研究

本论文以具有巨大应用前景的PHBV作为研究对象，针对PHBV结晶速率低，易产生二次结晶，从而严重影响其加工性能和力学性能的稳定性等方面的缺点，根据PHBV的分子结构和脆性的机理分析，试图采用添加成核剂的方法，提高PHBV的结晶速率和结晶度，从而缩短PHBV的加工成型周期，控制其聚集态结构，提高其制品的稳定性，改善材料的物理力学性能。并在此基础上，探讨PHBV异相成核结晶的机理，加深成核剂对聚合物有效成核机理的认识，更好的理解聚合物结晶过程。1．添加成核剂的量达到0.5wt％时，对苯二甲酸（TPA）对PHBV起到了显著的结晶成核作用。结晶起始温度提高了约20℃，结晶速率达到最大值所对应的温度T_p提高了30℃，结晶烙增加了15J/g，结晶速率提高了4.4倍。这些数据表明，TPA是一种对PHBV极为有效的成核剂。2．加入成核剂TPA的PHBV表现出典型的双熔融行为，主要原因是TPA对PHBV的结晶成核作用和PHBV的熔融再结晶。低温侧的熔融峰对应着PHBV自熔体降温过程形成的结晶，高温侧的对应着PHBV升温过程中形成的结晶。3．TPA的成核作用大大的改变了PHBV的形态结构，使PHBV的球晶尺寸明显减小，球晶数量增大。4．TPA使PHBV晶体在（110）和（020）方向上微晶尺寸变大，晶区和非晶区的电子密度差增大。5．添加0.5wt％的TPA后，PHBV的断裂伸长率从4％提高到10％。6．TPA、IPA、淀粉和山梨醇对PHBV的结晶都具有很明显的成核作用，其原因可能是化学结构上都具有极性基团。7．红外光谱研究没有能够有效的给出PHBV与TPA是否存在特殊相互作用，从而导致TPA对PHBV的结晶成核作用的证据，但是，PHBV拨基伸缩振动谱带随温度的变化却给出了TPA对PHBv的结晶成核作用始于160℃高温。

Summer monsoon intensity controls C-4/C-3 plant abundance during the last 35 ka in the Chinese Loess Plateau: Carbon isotope evidence from bulk organic matter and individual leaf waxes

IEECAS SKLLQG

Near-infrared polymer light-emitting diodes based on infrared dye doped poly(N-vinylcarbazole) film

Infrared light-emitting diodes possess potential applications in optical communication and safety detection. in this paper, we fabricated near-infrared light-emitting diodes possess potential applications in optical communication and safety detection. in this paper, we fabricated near-infrared polymer light-emitting diode employing a commercial near-infrared (NIR) organic dye as an emissive dopant dispersed within poly(N-vinylcarbazole) (PVK) by spin-casting method. The used device structure was indium tin oxide/3,4-polyethylene-dioxythiophene-polystyrene sulfonate/PVK: NIR dye/Al.

The effect of annealing treatment on performance of interdiffused organic photovoltaic devices

We fabricated the interdiffused organic photovoltaic devices, which composed of poly (2-methoxy-5-(2'-ethylhexyloxy)-1, 4-phenylenevinylene) (MEH-PPV) and buckminsterfullerene (C-60), by annealing treatment. After annealing, C60 diffused into the MEH-PPV layer, in consequence, MEH-PPV/C-60 interfacial area was increased and their interface became closer proximity. The results lead to reduce reverse-bias saturation current (J(s)), and increase the open-circuit voltage (V-OC) and the short-circuit current (J(SC)).

Synthesis of Soluble Poly(arylene ether sulfone) Ionomers with Pendant Quaternary Ammonium Groups for Anion Exchange Membranes

A new bisphenol monomer, 2,2'-dimethylaminemetllylene-4,4'-biphenol (DABP), was easily prepared by Mannich reaction of dimethylamine and formaldehyde with 4,4'-biphenol. Novel partially fluorinated poly(arylene ether sulfone)s with pendant quaternary ammonium groups were prepared by copolymerization of DABP, 4,4'-biphenol, and 3,3',4,4'- tetrafluorodiphenylsulfone, followed by reaction with iodomethane. The resulting copolymers PSQNI-x (where x represents the molar fraction of DABP in the feed) with high molecular weight exhibited outstanding solubility in polar aprotic solvents; thus, the flexible and tough membranes of PSQNI-x with varying ionic content could be prepared by casting from the DMAc solution. Novel anion exchange membranes, PSQNOH-x, were obtained by an anion exchange of PSQNI-x with 1 N NaOH.