Determination of Hg(II) in waters by on-line preconcentration using Cyanex 923 as a sorbent - Cold vapor atomic absorption spectrometry

Using a solid phase extraction mini-column home-made from a neutral extractant Cyanex 923, inorganic Hg could be on-line preconcentrated and simultaneously separated from methyl mercury. The preconcentrated Hg (11) was then eluted with 10% HNO3 and subsequently reduced by NaBH4 to form Hg vapor before determination by cold vapor atomic absorption spectrometry (CVAAS). Optimal conditions for and interferences on the Hg preconcentration and measurement were at 1% HCl, for a 25 mL sample uptake volume and a 10 mL min(-1) sample loading rate. The detection limit was 0.2 ng L-1 and much lower than that of conventional method (around 15.8 ng L-1). The relative standard deviation (RSD) is 1.8% for measurements of 40 ng L-1 of Hg and the linear working curve is from 20 to 2000 ng L-1 (with a correlation coefficient of 0.9996). The method was applied in determination of inorganic Hg in city lake and deep well water (from Changchun, Jilin, China), and recovery test results for both samples were satisfactory.

The research of cellulose derivatives as chiral stationary phases and high performance liquid chromatography with polarimeter as on-line detector

Three cellulose derivatives were synthesized and used as chiral stationary phases based on silica gel. The effects of adsorbances on the column numbers and stabilities have been investigated. These stationary phases exhibited high chiral recognition for various racemates. At the same time, the on-line curves of polarimeter were obtained by high performance liquid chromatography with polarimeter as on-line detector.

Growth rates of different polymorphs from interspherulitic boundary profiles

Quantitative data on the crystallization kinetics of polymorphic polymers can be derived from the investigation of gross spherulitic morphology formed in isothermal conditions. Depending on distance between centers, and the time lag between their formation and relative growth rates, various types of boundary lines can be generated by the impinging of two spherical bodies whose radii increase linearly with time, In polymorphic polymers, different types of spherulites often develop simultaneously at different rates from sporadic or predetermined nuclei. In same cases, the so-called growth transformation, in which a nucleus of the fast growing specie is formed at the tip of an advancing lamella of the slower crystal form, provides an alternative mode of nucleation, It is shown that if only one event of growth transformation takes place at the front of a slow growing body, the fast growing spherulite swallows the parent one and the resultant shape of interspherulitic boundary is described by two symmetrical logarithmic spirals whose parameters can be extracted from micrographs taken at the end of crystallization. These concepts are applied to determine the radial growth rate of gamma form spherulites of polypivalolactone in a wide range of temperatures through analysis of the alpha/gamma interspherulitic profiles formed in isothermal conditions and direct measurement of the growth rate of the alpha counterparts at the same temperature.

RESOLUTION OF CLOSELY SPACED LINES WITH KALMAN FILTERING IN INDUCTIVELY COUPLED PLASMA ATOMIC EMISSION-SPECTROMETRY

Effects of some factors on the performance of our Kalman filter in discrimination of closely spaced overlapping signals were investigated. The resolution power of the filter for overlapping lines can be strengthened by reduction of the step size in scans. The minimum peak separation of two lines which the Kalman filter can effectively handle generally equals two to three times the step size in scans. Significant difference between the profiles of the analysis and interfering lines and multiple lines from matrix in the spectral window of the analysis line are very helpful for the Kalman filter to discern closely spaced analysis and interfering signals correctly, which allow the filter well to resolve the line pair with very small peak distance or even the entirely coincident lines.

Comparative proteomic profiles of the hepatopancreas in Fenneropenaeus chinensis response to hypoxic stress

Hypoxia, as one suboptimal environmental condition, can affect the physiological state of shrimp during pond aquaculture. To better understand the mechanism of response to hypoxic stress in Chinese shrimp Fenneropenaeus chinensis, proteome research approach was utilized. Differentially expressed proteins of hepatopancreas in adult Chinese shrimp between the control and hypoxia-stressed groups were screened. By 2-DE analysis, 67 spots showed obvious changes after hypoxia. Using LC-ESI-MS/MS, 51 spots representing 33 proteins were identified including preamylase, arginine kinase, phosphopyruvate hydratase, citrate synthase, ATP synthase alpha subunit, chymotrypsin BI, chitinase, ferritin, C-type lectin receptors, transketolase, formylglutathione hydrolase, formyltetrahydrofolate dehydrogenase, aldehyde dehydrogenase, glutathione peroxidase, cytosolic manganese superoxide dismutase, protein disulfide isomerase, beta-actin, oncoprotem nm23, crustacyanin-Cl and so on. These proteins could be functionally classified into several groups such as proteins related to energy production, metabolism-related proteins, immune-related proteins, antioxidant proteins, chaperones, cytoskeleton proteins and ungrouped proteins. The transcription levels of ten selected genes encode the identified proteins were analyzed by real-time PCR at different sampling times of hypoxia. This study is the first analysis of differentially expressed proteins in the hepatopancreas of shrimp after hypoxia and provides a new insight for further study in hypoxic stress response of shrimp at the protein level.

Identification of a novel relish homolog in Chinese shrimp Fenneropenaeus chinensis and its function in regulating the transcription of antimicrobial peptides

Penaeid shrimp, as an invertebrate, relies on the innate immunity to oppose the microbial invaders. Antimicrobial peptides (AMP) are an integral component of the innate immune system in most organisms and function as an early first line of defense against pathogens, but the knowledge about the pathways to regulate the shrimp AMP gene expression is still absent up to date. In the current study, a Relish homolog (FcRelish) was cloned from Chinese shrimp Fenneropenaeus chinensis. The full length cDNA of FcRelish consists of 2157 bp, including 1512 bp open reading frame, encoding 504 amino acids. The predicted molecular weight of FcRelish is 57 kDa, and the theoretical PI is 7.00. Spatial expression profiles showed that FcRelish had the highest expression levels in the hemocytes and lymphoid organ. Both Vibrio anguillarium and Micrococcus lysodeikticus stimulation to shrimp can affect the transcription profile of FcRelish. Silencing of FcRelish through DsRNA interference can greatly change the transcription profile of AMP. Therefore, we suggest that FcRelish identified in the present study is closely related to the transcription of AMP, and then we inferred that Imd pathway might exist in shrimp. (C) 2009 Elsevier Ltd. All rights reserved.

Expression profiles of penaeidin from Fenneropenaeus chinensis in response to WSSV and vibrio infection by real-time PCR

Penaeidin from Chinese shrimp (Fenneropenaeus chinensis) has proved to be one of the most important antimicrobial peptides in the bodies of animals. The relative quantitative real-time PCR method is developed to study through time, the mRNA expression profile of penaeidin in the muscle and haemocyte tissue of Chinese shrimp infected with vibrio (Vibrio anguillarum) and WSSV (white spot syndrome virus). Research results showed that the same pathogens infection experiments produced similar gene expression profile in different tissues while different expression profiles appeared in the same tissues infected by different exterior pathogens. In vibrio infection experiments, a "U" Re expression profile resulted. Expression levels of penaeidin increased and surpassed the non-stimulated level, indicating that penaeidin from Chinese shrimp has noticeable antimicrobial activities. In WSSV infection experiments, the expression profile appeared as an inverse "U" with the expression of penaeidin gradually decreasing to below baseline level after 24 h. The expression of antimicrobial peptides gene in mRNA level in response to virus infection in shrimp showed that international mechanisms of virus to haemocytes and microbial to haemocytes are completely different. Decline of penaeidins expression levels may be due to haemocytes being destroyed by WSSV or that the virus can inhibit the expression of penaeidins by yet undiscovered modes. The expression profiles of penaeidin in response to exterior pathogen and the difference of expression profiles between vibrio and WSSV infection provided some clues to further understanding the complex innate immune mechanism in shrimp.

Comparison of Gene Expression Profiles of Fenneropenaeus chinensis Challenged with WSSV and Vibrio

Microarray technique was used to analyze the gene expression profiles of shrimp when they were challenged by WSSV and heat-inactivated Vibrio anguillarum, respectively. At 6 h post challenge (HPC), a total of 806 clones showed differential expression profile in WSSV-challenged samples, but not in Vibrio-challenged samples. The genes coding energy metabolism enzyme and structure protein were the most downregulated elements in 6 h post WSSV-challenged (HPC-WSSV) tissues. However, a total of 155 clones showed differential expression in the Vibrio-challenged samples, but not in WSSV-challenged samples. Serine-type endopeptidase and lysosome-related genes were the most upregulated elements in tissues 6 h post Vibrio challenge (HPC-Vibrio). Totally, 188 clones showed differential expression in both 6 and 12 HPC-WSSV and HPC-Vibrio samples. Most of the differentially expressed genes (185/188) were downregulated in the samples of 12 HPC-WSSV, whereas upregulated in the samples at 6 and 12 HPC-Vibrio and 6 HPC-WSSV. The expression profiles of three differentially expressed genes identified in microarray hybridization were analyzed in hemocytes, lymphoid organ, and hepatopancreas of shrimp challenged by WSSV or Vibrio through real-time PCR. The results further confirmed the microarray hybridization results. The data will provide great help for us in understanding the immune mechanism of shrimp responding to WSSV or Vibrio.

Pervasive autocorrelation of the chemical index of alteration in sedimentary profiles and its palaeoenvironmental implications

The chemical index of alteration has been used widely for reconstruction of the palaeoclimate. However, the mechanisms and environmental factors controlling the chemical index of alteration of sediments are not yet fully understood. In this study, autocorrelations of the chemical index of alteration in nine sedimentary profiles, from both the land and the sea, spanning different geological times, are discussed. The sediments of these profiles have different origins (dust, fluvial or ocean sediments) and are from various climate situations and sedimentary environments. Autocorrelations of chemical index of alteration series are ubiquitously evident in all profiles. It is suggested here that autocorrelations may be caused by post-depositional changes such as persistent weathering and diagenesis. As a result, the chemical index of alteration may not reflect climatic conditions during the time of sediment deposition. This study strongly recommends the confirmation of the reliability and veracity of the chemical index of alteration before it is adopted to evaluate the weathering degree of parent rocks and to reconstruct the past climate. Significant autocorrelations in loess profiles were specifically observed, suggesting that the existing understanding of loess deposition in terms of climate conditions requires re-examination, and that previous reconstructions of rapid climate changes (for example, in centennial-millennial scales) should be treated with caution.

The characteristics of BSRs and their derived heat flow on the profile 973 in the northeastern South China Sea

Processing of a recently acquired seismic line in the northeastern South China Sea by Project 973 has been conducted to study the character and the distribution of gas hydrate Bottom-Simulating Reflectors (BSRs) in the Hengchun ridge. Analysis of different-type seismic profiles shows that the distribution of BSRs can be revealed to some extents by single-channel profile in this area, but seismic data processing plays an important role to resolve the full distribution of BSRs in this area. BSR' s in the northeastern South China Sea have the typical characteristics of BSRs on worldwide continental margins: they cross sediment bed reflections, they are generally parallel to the seafloor and the associated reflections have strong amplitude and a negative polarity. The characteristics of BSRs in this area are obvious and the BSRs indicate the occurrence of gas hydrate-bearing sediments in the northeastern South China Sea. The depth of the base of the gas-hydrate stability zone was calculated using the phase stability boundary curve of methane hydrate and gas hydrate with mixture gas composition and compared with the observed BSR depth. If a single gradient geothermal curve is used for the calculation, the base of the stability zone for methane hydrate or gas hydrate with a gas mixture composition does not correspond to the depth of the BSRs observed along the whole seismic profile. The geothermal gradient therefore changes significantly along the profile. The geothermal gradient and heat flow were estimated from the BSR data and the calculations show that the geothermal gradient and heat flow decrease from west to east, with the increase of the distance from the trench and the decrease of the distance to the island arc. The calculated 2 heat flow changes from 28 to 64 mW/m(2), which is basically consistent with the measured heat flow in southwestern offshore Taiwan.

砂泥岩储层测井产能预测方法研究

Productivity prediction is very important in the exploration and development of oilfields. Using well log data to predict productivity is a front-line technology， which is key issue in petroleum exploration phase. The essential factors of productivity prediction is building practical models and correcting various causes to improve precision of prediction parameters. Any errors of parameters selections can affect the calculation of productivity prediction; therefore， how to improve research means and calculation accuracy is an important task of productivity prediction. Theory and case examples are deeply and comprehensively studied in the paper. Based on the theory of mud-filtrate invasion and experimental results， the damage of drilling， cementing， perforating，acidizing and fracturing were investigated. The damage depth was quantitatively evaluated by log data， based on this， the processing results of reservoir sensitivity were used to analysis quantitatively the damage of reservoir. The productivity prediction and reservoir damage were initiatively incorporated according to well logging， and the precision of productivity prediction was effectively improved. The method of NMR was explored to calculate the fluid viscosity on the basis of reservoir physical method， and the differences between the two methods were compared in the paper. From the theory fluid flow in porous media， various of theoretical models of production prediction were explored and several practical models were consided， such as productivity index method， improved productivity index method， improved Bearder method， SVM and so on. The characteristic and the application scope of these methods were studied. The inflow productivity and outflow productivity were incorporated and nodal analysis method was used to forecast wellhead yield， thus achieved scientifically production. On the applied background of conventional logging suite， the applying of special items or new logging method which is practical in the research area were studied， the logging suite was further optimized， and the precision of forecast was improved. On the basis of the modeling and the calculation of parameters， these methods were verified and analyzed， and the reconstruct principle was also built for block reservoir. The research block was processed by these methods and compared with testing data. Based on above the research， a technological system which is practical for shaly sand profiles in Shengli Oilfield was built. The system can reach commercialized degree，and satisfied the need of exploration and development of the oilfield.

陆地三分量三维地震勘探技术研究与应用

With the development of oil and gas field exploration, it becomes harder to search new reserves. So a higher demand of seismic exploration comes up. Now 3C3D seismic exploration technology has been applied in petroleum exploration domains abroad. Comparing with the traditional P-wave exploration, the seismic attributes information which provided by 3C3D seismic exploration will increase quickly. And it can derive various combined parameters. The precision of information about lithology, porosity, fracture, oil-bearing properties, etc which estimated by above parameters was higher than that of pure P-wave exploration. These advantages mentioned above lead to fast development of 3C3D seismic technology recently. Therefore, how to apply the technology in petroleum exploration field in China, how to obtain high quality seismic data, and how to process and interpret real data, become frontier topics in geophysical field nowadays, which have important practical significance in research and application. In this paper, according to the propagation properties of P-wave and converted wave, a study of 3C3D acquisition parameters design method was completed. Main parameters included: trace interval, shot interval, maximum offset, bin size, the interval of receiving lines, the interval of shooting lines, migration aperture, maximum cross line distance, etc. Their determination principle was given. The type of 3C3D seismic exploration geometry was studied. By calculating bin attributes and analyzing parameters of geometry, some useful conclusions were drawn. With the method in this paper, real geometries for continental lithology stratum gas reservoir and fractured gas reservoir were studied and determined. In the static method of multi-wave, the near surface P-wave, S-wave parameter investigation method has been advanced, and this method has been applied for the patent successfully; the near surface P-wave, S-wave parameter investigation method and the converted refraction wave first arrival static techniques have been integrally used to improve the effectiveness of converted wave static. In the aspect of converted wave procession, the rotation of horizontal component data, the calculation of converted wave common conversion bin, the residual static of converted wave, the velocity analysis of the common conversion point (CCP), the Kirchhoff pre-stack time migration of converted wave techniques have been applied for setting up the various 3C3D seismic data processing flows based on different geologic targets, and the high quality P-wave, converted-wave profiles have been acquired in the actual data processing. In the aspect of P-wave and converted-wave comprehensive interpretation, the thoughts and methods of using zero-offset S-wave VSP data to calibrate horizon have been proposed; the method of using P-wave and S-wave amplitude ratio to predict the areas of oil and gas enrichment has been studied; the method of inversion using P-wave combined with S-wave has been studied; the various P-wave, S-wave parameters(velocity ratio, amplitude ratio, poisson ratio) have been used to predict the depth, physical properties, gas-bearing properties of reservoirs; the method of predicting the continental stratum lithology gas reservoir has been built. The above techniques have all been used in various 3D3C seismic exploration projects in China, and the better effects have been gotten. By using these techniques, the 3C3D seismic exploration level has been improved.

南海大陆边缘地壳结构与盆地形成机制--以珠江口－琼东南盆地为例

South China Sea is located in the convergence of Eurasian plate, the Pacific Ocean plate and Indian Ocean-Australia plate. The total area is about 3,500,000 km2, the geologic structure is complicated, and the structure line cut off reciprocal is the marginal sea taking form by that the seafloor spreads during the middle Oligocene. South China Sea continental margin have developed more than 10 large oil-gas bearing basins and a number of medium-small sized basins. These basins contain abundant mineral resources such as oil & gas. The marginal deepwater area in the north part of South China Sea has become our country’s strategic energy prospecting frontier. The deepwater area of Zhujiangkou and Qiongdongnan basins is the research target in this thesis. The thesis studied deep structure and the earth dynamics of the north part of South China Sea margin, and these researches provide scientific basis for oil-gas resources strategic investigation and valuation in deepwater sea area of north part slope of South China Sea. In order to develop the research of rebuilding velocities and density architecture of earth shell in region of interest, in marginal deepwater area in the north part of South China, we adopted 14 long-cable seismic reflection profile data of 3556.41 kilometers in total, the gravity measurement data along profiles (3851.44 kilometers in total), the magnetic observation along profiles (3838.4 kilometers in total) and depth measurement along profile, the logging data of 11 wells in project, the interpreted fault parameter and preexisting geologic and geophysical research achievement. This thesis has carried out concretely studying research as follows: 1. Overlay-velocity data sampling and analysis, interval velocity calculation, time-depth conversion, model building of earth shell velocity and layering character of earth shell are studied on 14 deep sections. Velocity structure in region of interest has revealed: Changchang is the sag with thinnest crust in Qiongdongnan basin; the sedimentary thickness lowers gradually from north to south, and the thickness change from west to east is milder. The sags’ sedimentary velocities in Qiongdongnan basin have obvious demarcation. The velocity of the 8000 meters sedimentary rocks is 4700 m/s in Shunde sag and Baiyun sag, and is the lowest; at that depth, the velocity very different in Liwan sag and Baiyun sag, which is about 800m/s. 2. Extracting gravity data and building of initial crust density model along the section; With Bouguer gravity anomaly data as constraint, revising density distributes of initial model, and building the crust density model. 3. With crust velocity and density as constraint, correcting the effect of thermobaric field and constructing constitution structure of rock in region of interest. By this research, we known that rocks in Zhujiangkou upper crustal layer are chiefly granite-gneiss, quartzite, granodiorite and basalt, however, rocks in Qiongdongnan basin upper earth shell are chiefly composed of granite-gneiss, quartzite, granodiorite, diorite and basalt. 4. Synthetically crust velocity and density structure, gaining expanding factor on crust and entire crust along section. The result is indicated: the expanding factor in every sag rises from northwest to southeast, which have reflected thinning characteristic of crust from continent to ocean. Intra-crustal deformation degree in Changchang and Ledong-Lingshui sag is bigger than that in Songnan-Baodao sag. Entire crust extension factor in Changchang and Songnan-Baodao sag is greater than that in Ledong-Lingshui sag, which can make an explanation of frequently event and longer heating process in middle-east of Qiongdongnan basin. 5. Synthesize multidisciplinary information to discuss the earth dynamics significance of discordogenic seismic profile in deepwater area of Zhujiangkou and Qiongdongnan basins.