Designing a coupler for the intersatellite optical communication system

Coupling a single-mode laser diode with 200 mW to a single-mode fiber (SMF) through an orthonormal aspherical cylindrical lens and a GRIN lens for the intersatellite optical communication system is proposed and demonstrated. We experimentally studied how the coupling efficiency changes with the SMF's position displacement and axial angle variation, and obtained 80 mW output power at the end of the SMF, which shows that the coupling units have satisfied the designed request. (c) 2007 Elsevier GmbH. All rights reserved.

Accuracy analysis of parallel plate interferometer for angular displacement measurement

The measurement accuracy of a parallel-plate interferometer for angular displacement measurement is analyzed. The measurement accuracy of angular displacement is not only related to the accuracy of phase extraction, but also related to initial incident angle, refraction index and thickness of plane-parallel plate as well as wavelength's stability of laser diode, etc. Theoretical analysis and computer simulation show that the measurement error of the angular displacement bears a minimum value when choosing an optimal initial incident angle in a large range. These analytical results serve as a guide in practical measurement. In this interferometer, reducing the refraction index or increasing the thickness of the parallel plate can improve the measurement accuracy; and the relative error of the phase measurement is 3.0 x 10(-4) corresponding to 1 degrees C temperature variation. Based on these theoretical and experimental results, the measurement accuracy of the parallel-plate interferometer is up to an order of 10(-8) rad. (c) 2007 Elsevier Ltd. All rights reserved.

Real-time micro-vibration measurement in sinusoidal phase-modulating interferometry

As there exist some problems with the previous laser diode (LD) real-time microvibration measurement interferometers, such as low accuracy, correction before every use, etc., in this paper, we propose a new technique to realize the real-time microvibration measurement by using the LD sinusoidal phase-modulating interferometer, analyze the measurement theory and error, and simulate the measurement accuracy. This interferometer utilizes a circuit to process the interference signal in order to obtain the vibration frequency and amplitude of the detective signal, and a computer is not necessary in it. The influence of the varying light intensity and light path difference on the measurement result can be eliminated. This technique is real-time, convenient, fast, and can enhance the measurement accuracy too. Experiments show that the repeatable measurement accuracy is less than 3.37 nm, and this interferometer can be applied to real-time microvibration measurement of the MEMS. (C) 2007 Elsevier GmbH. All rights reserved.

Stable single frequency and single polarization DFB fiber lasers operated at 1053 nm

Stable single-frequency and single-polarization distributed-feedback (DFB) fiber laser was realized by giving a pressure on the phase shift region of the fiber grating. The output wavelength of the DFB fiber laser is 1053 nm. When the pump power of 980 nm laser diode is 100 and 254 mW, the output power can reach 8.3 and 37.1 mW and the polarization extinction ratio was 26 and 20 dB, respectively. After chopped by Acousto-optic modulator (0.3 Hz), the pulse peak value variance is 4.65%(peak to peak) and 1.098% (RMS) for 31 min. (C) 2006 Elsevier Ltd. All rights reserved.

板条热容激光器的二维热特性

固体热容激光器（SSHCL）作为高功率固体激光器的一个重要发展方向,引起人们广泛关注。数值模拟激光介质板条在热容方式下工作的温度和应力分布是了解该类激光器工作特性的一种有效手段,采用平面应力近似法导出了半导体激光器抽运热容激光介质板的二维温度和应力分布公式,同时也对二维抽运光吸收密度、介质板温度分布和折射率变化进行了分析与讨论。数值计算的结果表明二维效应的温度分布和应力分布要比一维效应给出的分布更均匀。

激光二极管端面抽运Nd∶YVO4固体激光器热致光束畸变非对称的平衡

由于a轴切割Nd∶YVO4晶体的非对称性,使得激光二极管(LD)端面抽运Nd∶YVO4固体激光器不同于Nd∶YAG激光器,输出的激光经常产生非对称结果。用有限元法分析激光二极管端面抽运a轴切割Nd∶YVO4固体激光器的晶体热效应,包括温度分布、内部应力和产生的形变。分析结果表明端面抽运a轴切割Nd∶YVO4晶体产生了椭球热透镜效应。从结构方面和抽运方面提出了热透镜非对称性的平衡方法,实验验证了方法的可行性。

高稳定激光二极管抽运Nd∶YLF再生放大器

设计并实现了一种放大纳秒激光脉冲的高稳定的激光二极管(LD)抽运Nd∶YLF再生放大器。为了获得高稳定的输出,再生放大器工作在饱和状态。此时,再生放大器输出稳定性最好,而且注入激光脉冲能量波动引起的输出激光脉冲波动被抑制。由于增益饱和效应,再生放大器输出脉冲出现时域波形失真,附加后缀脉冲能够减弱时域波形失真。放大器工作波长1053nm,工作频率1Hz。输入240pJ的3ns方波激光脉冲,输出激光脉冲能量4.2mJ,总增益大于107,不稳定度小于1%(均方根),方波扭曲1.33。为3ns方波激光脉冲引入其本身幅度0.75倍的后缀脉冲,输出激光脉冲方波扭曲由1.33降至1.17。

Yb:YAG/YAG复合陶瓷薄片连续和调Q输出特性

采用面泵浦的CAMIL结构，我们研究了970 nm泵浦的Yb:YAG/YAG复合陶瓷薄片激光器，获得了连续和调Q的激光输出。在连续运转情况下，获得了最高1.05 W的激光输出，中心波长为1031 nm，后腔输出镜透射率为2％。我们同时获得了声光调Q的脉冲输出，重复频率从1 kHz到30 kHz，脉宽分别从166 ns到700 ns。

改善高功率激光二极管阵列光束质量的一种新方法

根据波导模理论,推导了高功率激光二极管阵列的远场分布,根据其分布特点,设计了一种离轴外腔.运用这种外腔,在工作电流为17A时,光束的束宽积从自由运转时的1100mm.mrad减小到128mm.mrad,二极管阵列的光束质量提高了8.5倍左右,输出功率约为自由运转时的75%.

机载测深激光雷达千赫兹全固态激光器设计及特性研究

将千赫兹高功率全固态Nd：YAG激光器的增益介质当作厚透镜处理，使用矩阵的方法对等效热透镜腔进行分析。采用多条半导体激光列阵侧向紧凑抽运结构设计，提高了增益介质光抽运的均匀性。根据实际抽运功率，通过模拟计算，设计了平凸非稳腔。选择的凸面全反镜的最佳曲率半径有效地补偿了增益介质热透镜效应，激光器实现了动态稳腔运转，激光脉冲能量输出斜度效率大于13％，光束发散角优于1.3mrad。

半导体激光直接倍频的488nm蓝光激光器

利用波导型准相位匹配周期极化反转铌酸锂（PPLN）晶体直接倍频波长为976nm的连续半导体激光二极管，在最佳晶体工作温度（28℃）下，获得了波长为488nm的连续蓝光输出，最大输出功率大于20mW。所用的晶体尺寸为8mm×1．4mm×1mm，波导截面为4．5μm×3．5μm，极化周期为5．2μm。研究了波导型周期极化反转铌酸锂晶体的倍频效率与温度的关系，与普通的周期极化反转铌酸锂相比，倍频效率与温度关系的敏感度较低。同时，由于晶体可以在室温下工作，简化了加温与温控部件，提高了整机的工作效率。在此实验的基础

部分抽运的板条激光器的热效应分析

基于热传导方程和高斯-赛德尔数值计算方法，对部分抽运板条激光器的温度分布、热应力和热致折射率变化等热效应进行了详细分析，并与单侧抽运及双侧抽运方式进行了比较。结果表明，设计合理的部分抽运板条激光器，可以获得较高的抽运效率，其热效应相比于均匀抽运的情况并没有显著劣化，不论是采用锯齿形传播方式还是直线传播方式的激光器都可以获得较好的光束质量，当一束高斯激光直线经过板条晶体中部时，光束质量因子为1．4，若采用锯齿形传播方式，则光束质量因子可提高到1．1。

激光二极管连续抽运电光调Q Nd：YVO4激光器

报道了全固态激光器连续抽运高重复率电光调Q的实验和理论分析结果。用LGS（La3Ga5SiO14）晶体作电光调Q元件，在激光二极管（LD）端面抽运Nd：YVO4激光器中实现了较高重复率的电光调Q输出。实验中在10^4Hz重复率下，抽运功率为28w时，平均功率超过5W，脉冲宽度为7ns，峰值功率为70kW，并对不同重复率时的脉冲输出进行了比较，在低重复率下，脉宽〈6．5ns，峰值功率超过100kW。在理论上，通过对连续抽运时的电光调Q速率方程进行修正，并考虑放大自发辐射（ASE）的影响，对调Q激光器的储能过

输出5W的电光调Q Nd：YAG陶瓷激光器

研究了激光二极管（LD）侧向抽运的Nd：YAG陶瓷电光调Q激光器的激光输出特性。该激光器采用九组激光二极管线阵列（LDA）侧面紧密环绕均匀排布的抽运结构，并用微通道热汇冷却技术冷却。在电光调Q方式下，重复频率为100Hz，抽运单脉冲能量为416mJ时，用尺寸为庐5mm×75mm，掺杂原子数分数为1％的Nd：YAG陶瓷棒，获得50mJ的1064nm激光输出，脉冲宽度为12ns，斜率效率达24％。并实验测量和分析了偏振片，KD^＊P晶体，四分之一波片等调Q器件的插入损耗。测量了输出激光时间波形和光斑的光强空间

双侧面90°抽运微通道致冷Yb：YAG板条激光器

报道了采用带有微柱镜的激光二极管阵列（LDA）双侧面90°排布抽运的Yb：YAG板条激光器，实验中使用的激光晶体尺寸为6mm×10mm×1mm，掺杂原子数分数为3％。抽运光通过自行设计的聚光系统聚焦成10mm×1mm的光斑进行抽运，聚光系统的效率为75％，晶体表面功率密度达到1．9kW／cm^2，晶体内抽运光交叠区的体功率密度达到38kW／cm^3，远高于阈值的1．7kW／cm^3。当激光器采用平一凹腔结构，耦合输出为6％时激光单脉冲输出能量最高为25．5mJ，斜率效率为13％。插入声光调Q晶体后获得4．