Numerical Study On Transient Flow In The Deep Naturally Fractured Reservoir With High Pressure

According to the experimental results and the characteristics of the pressure-sensitive fractured formation, a transient flow model is developed for the deep naturally-fractured reservoirs with different outer boundary conditions. The finite element equations for the model are derived. After generating the unstructured grids in the solution regions, the finite element method is used to calculate the pressure type curves for the pressure-sensitive fractured reservoir with different outer boundaries, such as the infinite boundary, circle boundary and combined linear boundaries, and the characteristics of the type curves are comparatively analyzed. The effects on the pressure curves caused by pressure sensitivity module and the effective radius combined parameter are determined, and the method for calculating the pressure-sensitive reservoir parameters is introduced. By analyzing the real field case in the high temperature and pressure reservoir, the perfect results show that the transient flow model for the pressure-sensitive fractured reservoir in this paper is correct.

节理裂隙岩体爆破试验研究

首先利用超声波探测法对节理裂隙岩体进行了声波测试,对不同的节理裂隙岩体进行了质量评估.然后通过对节理裂隙岩体进行爆破漏斗试验,分析了节理裂隙对岩体中爆炸应力波传播、岩石破碎及爆破漏斗形成的影响,得出了一些有益结论,对节理裂隙岩体理论研究和指导工程实践具有一定的参考价值.

Numerical Analysis of Rainfall Infiltration in the Slope with a Fracture

With the finite volume method, a 2D numerical model for seepage in unsaturated soil has been established to study the rainfall infiltration in the fractured slope.The result shows that more rain may infiltrate into the slope due to existing fracture and then the pore pressure rises correspondingly. Very probably, it is one of the crucial factors accounting for slope failure. Furthermore a preliminary study has been conducted to investigate the influence of various fracture and rainfall factors such as the depth, width and location of a crack, surface condition, rainfall intensity and duration. Pore pressure and water volumetric content during the transient seepage are carefully examined to reveal the intrinsic mechanism.

Material response and failure mechanism of unidirectional metal matrix composites under impulsive shear loading

The material response and failure mechanism of unidirectional metal matrix composite under impulsive shear loading are investigated in this paper. Both experimental and analytical studies were performed. The shear strength of unidirectional C-f/A356.0 composite and A356.0 aluminum alloy at high strain rate were measured with a modified split Hopkinson torsional bar technique. The results indicated that the carbon fibers did not improve the shear strength of aluminum matrix if the fiber orientation aligned with the shear loading axis. The microscopic inspection of the fractured surface showed a multi-scale zigzag feature which implied a complicated shear failure mechanism in the composite. In addition to testing, the micromechanical stress field in the composite was analyzed by the generalized Eshelby equivalent method (GEEM). The influence of cracking in matrix on the micromechanical stress field was investigated as well. The results showed that the stress distribution in the composite is quite nonhomogeneous and very high shear stress concentrations are found in some regions in the matrix. The high shear stress concentration in the matrix induces tensile cracking at 45 degrees to the shear direction. This in turn aggravates the stress concentration at the fiber/matrix interface and finally leads to a catastrophic failure in the composite. From the correlation between the analysis and experimental results, the shear failure mechanism of unidirectional C-f/A356.0 composite can be elucidated qualitatively.

Enhanced Plasticity of Zr-Based Bulk Metallic Glass Matrix Composite with Ductile Reinforcement

A composite material containing uniformly distributed micrometer-sized Nb particles in a Zr-based amorphous matrix was prepared by suction cast. The resulting material exhibits high fractured strength over 1550 MPa and enhanced plastic strain of about 29.7% before failure in uniaxial compression test at room temperature. Studies of the serrations on the stress-strain curves and the shear bands on the fractured samples reveal that the amplitude of the stress drop of each serration step corresponds to the extent of the propagation of a single shear band through the materials. The composite exhibits more serration steps and smaller amplitude of stress drop due to the pinning of shear band propagation by ductile Nb particles.

岩体中的节理裂隙对爆破影响的试验研究

利用超声波探测法对节理裂隙岩体进行了声波测试,对不同的节理裂隙岩体进行了质量评估,通过对节理裂隙岩体进行爆破漏斗试验,分析了节理裂隙对岩体中爆炸应力波传播、岩石破碎及爆破漏斗形成的影响.结果表明,节理裂隙等结构弱面的存在严重阻碍了爆炸能量均匀分布,因此在爆破设计和施工中,应尽量使炮孔与结构弱面垂直布置,如果遇到含有夹层情况宜加大装药量;炮孔与结构弱面平行时,应尽量减小炮眼孔距和最小抵抗线,尽量采用单孔螺旋掏槽.

Measurement Of Fracture Toughness And Interfacial Shear Strength Of Hard And Brittle Cr Coating On Ductile Steel Substrate

The fracture toughness and interfacial adhesion properties of a coating on its substrate are considered to be crucial intrinsic parameters determining performance and reliability of coating-substrate system. In this work, the fracture toughness and interfacial shear strength of a hard and brittle Cr coating on a normal medium carbon steel substrate were investigated by means of a tensile test. The normal medium carbon steel substrate electroplated with a hard and brittle Cr coating was quasi-statically stretched to induce an array of parallel cracks in the coating. An optical microscope was used to observe the cracking of the coating and the interfacial decohesion between the coating and the substrate during the loading. It was found that the cracking of the coating initiated at critical strain, and then the number of the cracks of the coating per unit axial distance increased with the increase in the tensile strain. At another critical strain, the number of the cracks of the coating became saturated, i.e. the number of cracks per unit axial distance became a constant after this critical strain. Based on the experiment result, the fracture toughness of the brittle coating can be determined using a mechanical model. Interestingly, even when the whole specimen fractured completely under an extreme strain of the substrate, the interfacial decohesion or buckling of the coating on its substrate was completely absent. The test result is different from that appeared in the literature though the identical test method and the brittle coating/ductile metal substrate system are taken. It was found that this difference can be attributed to an important mechanism that the Cr coating on the steel substrate has a good adhesion, and the ultimate interfacial shear strength between the Cr coating and the steel substrate has exceeded the maximum shear flow strength level of the steel substrate. This result also indicates that the maximum shear flow strength level of the ductile steel substrate can be only taken as a lower bound estimate on the ultimate shear strength of the interface. This estimation of the ultimate interfacial shear strength is consistent with the theoretical analysis and prediction presented in the literature.

低渗透油藏渗吸法采油的数值模拟

针对渗吸法采油中的毛管力驱动项和流动系数的取值问题，根据地下流体渗流特征，建立了低渗透油藏渗吸法采油数学模型，给出了数值解法．定量分析了渗吸法采油的主要影响因素，通过实例验证，用该方法计算的各项动态指标与矿场实际值符合程度较高．结果表明：基质与裂缝渗透率之比小于O．Ol，油水黏度比小于15，毛管力较大的水湿油层比较适合于渗吸法采油，能够提高水驱采收率2％左右．

Molecular Dynamics Simulation of Methane Hydrate Dissociation Process in the Presence of Thermodynamic Inhibitor

The dissociation of methane hydrate in the presence of ethylene glycol (11.45 mol.L-1) at 277.0 K was studied using canonical ensemble (NVT) molecular dynamics simulations. Results show that hydrate dissociation starts from the surface layer of the solid hydrate and then gradually expands to the internal layer. Thus, the solid structure gradually shrinks until it disappears. A distortion of the hydrate lattice structure occurs first and then the hydrate evolves from a fractured frame to a fractional fragment. Finally, water molecules in the hydrate construction exist in the liquid state. The inner dissociating layer is, additionally, coated by a liquid film formed from outer dissociated water molecules outside. This film inhibits the mass transfer performance of the inner molecules during the hydrate dissociation process.

强地震荷载作用下含断层岩质边坡稳定性分析

基于岩石材料的弹塑性损伤理论, 引入两个独立的损伤变量分别控制岩石的拉压行为, 通过对地震菏载作用下边坡场地响应的有限元数值模拟, 总结含裂隙的岩质边坡发生局部损伤软化、破坏的仄域的扩展、演化过程和规律.结合对某大型水电坝坝址左岸的岩质边坡在强地震动载荷作用下(百年一遇、超越概率 2%)发生破坏的数值模拟, 揭示这类边坡滑坡的机理, 并根据模拟的结果, 对整治边坡破坏提出参考依据

捷安肽素对采后柑桔青绿霉菌抑制效果及作用机理研究

捷安肽素是一种由枯草芽孢杆菌（Bacillus subtilis）ZK 产生的抗真菌多肽。本文以柑桔青霉菌（Penicillium italicum）和绿霉菌（Penicillium digitaum）为供试真菌，研究了捷安肽素的抑菌性能及作用机理，为捷安肽素开发为有效的生物杀菌剂提供理论依据。全文共分两部分：第一部分：捷安肽素对柑桔青霉菌和绿霉菌抑制效果研究。采用琼脂扩散法测定捷安肽素对柑桔青霉菌和绿霉菌的抑菌活性。53.9 µg/mL 捷安肽素对绿霉菌和青霉菌的抑菌圈直径分别为26.7mm 和24.1mm。结果表明捷安肽素能够抑制柑桔青绿霉菌的生长，柑桔绿霉菌比青霉菌对捷安肽素敏感。在柑桔果实上，研究了不同浓度、不同接入时间的捷安肽素对柑桔青霉病和绿霉病的防治效果，并与常用化学杀菌剂抑霉唑、咪鲜胺、甲基硫菌灵和多菌灵作比较。53.9 µg/mL捷安肽素处理柑桔果实，柑桔青霉病和绿霉病发病率分别为5.0 %和5.3 %,比对照低95.0 %和94.7 %；柑桔青霉病和绿霉病的病情指数分别为1.87 和2.18，比对照低73.73 和97.82。结果表明，捷安肽素能够有效地防治柑桔青绿霉病。与对照相比，捷安肽素先于或后于柑桔青绿霉菌接入时，对柑桔青绿霉菌均有抑制作用，但抑制效果随接入间隔时间的增长而降低。第二部分：捷安肽素对绿霉菌作用机理研究。首先在光学显微镜和透射电镜下观察捷安肽素处理后绿霉菌菌丝表面形态结构与菌丝体内超微结构的变化。形态观察发现，捷安肽素处理24h以内，绿霉菌菌丝结构无变化。捷安肽素作用36h后，绿霉菌菌丝不规则缢缩和膨大。48h后，在绿霉菌菌丝顶端、中部、末端的多处细胞均可发生畸形的球状结构，这种畸变结构随处理的延长而增加，致使细胞成为捻珠状。处理72 h后，畸变球形细胞开始断裂离解。处理96h后，镜下几乎无完整菌丝，成单个的球状细胞，部分细胞出现破裂。而对照菌丝表面光滑，结构完整。通过透射电镜观察发现，与对照相比，捷安肽素处理后，绿霉菌细胞壁、细胞膜轮廓模糊不清，细胞质外泄。推测捷安肽素能够使绿霉菌细胞膜通透性发生改变。进一步实验利用紫外-可见分光光度计检测捷安肽素作用后绿霉菌胞外液紫外吸光度的变化，表明捷安肽素作用于绿霉菌菌丝后，细胞内蛋白质、核酸缓慢泄漏。通过Atomscan Advantage单道扫描等离子体发射光谱仪(ICP)测定捷安肽素作用后菌丝体内K+浓度的改变，结果表明捷安肽素作用于柑桔绿霉菌1h内，菌丝体内K+含量迅速下降，为对照绿霉菌K+含量的37.53 %，1 h后菌丝体内K+含量变化趋于平缓。K+的迅速泄漏，以及蛋白质、核酸的泄漏表明捷安肽素通过迅速改变绿霉菌细胞膜通透性，使绿霉菌菌丝生长受到抑制。Jiean-peptide produced by Bacillus subtilis ZK has broad-spectrumresistance to plant pathogens. In this study, we investigated the antifungal propertyand the possible antifungal mechanism of jiean-peptide against two commonphytopathogenic fungi of citrus fruits: blue molds (P. italicum) and green molds (P.digitatum).The paper involved two parts:Part 1 is the study of the antifungal property of jiean-peptide against blue moldsand green molds of citrus fruits. The in vitro inhibition effect of jiean-peptide againstblue molds and green molds was detected by agar diffusion method. The diameters ofinhibition zones of green molds and blue molds are 26.7mm and 24.1mm respectivelyby treating with 53.9 µg/mL jiean-peptide. It shows that jiean-peptide effectivelyinhibits the both phytopathogenic fungi, and it is more effective for inhibiting greenmolds than blue molds. The effectiveness of jiean-peptde to inhibit green molds andblue molds in vivo was investigated compared with four conventional fungicides thatare imazalil, prochloraz, carbendazin and methylthiophanate. The result is that the incidences of the blue mold disease and green mold disease are 5.0 % and 5.3 %, thedisease severities are 1.87 and 2.18 respectively when citrus are inoculated with 53.9µg/ml jiean-peptide. The decay incidences and disease severities were significantlyreduced by treating with jiean-peptide compared with the control. The results indicateJiean-peptide is effective for controlling blue molds and green molds on citrus. Theoptimized inoculation time was also investigated. When inoculated with jiean-peptideat 0 h, 6 h, 12 h, 24 h and 48 h before or after pathogens’ inoculation, Jiean-peptidecan suppress the occurrence of blue molds and green molds compared with the control, but the effect of later inoculation decreases compared with the inoculation at the sametime.In Part 2, we investigated the possible antifungal mechanism against greenmolds of citrus. At first, we observed the exterior morphological changes andultrastructural changes of blue molds under light microscopy (LM) and transmissionelectron microscopy (TEM). Compared with untreated control cells which aregenerally uniform in shape, the appearances of treated hyphae change obviously. Itshows that some cells of hyphae irregularly shrink or enlarge when cultured for 36h.When the treating time of jiean-peptide increases, the aberrance of the hyphaebecomes more obvious, and hyphae exhibit the moniliform appearances. Finally, thereis no intact hypha leaved except only single cells, and some of which appear fractured.By transmission electron microscopy (TEM) observation, we find that the outline ofthe cell wall and the cell membrane of hyphae are blurry, and the cytoplasma oozesout. The observation result under LM and TEM suggests that jiean-peptide mightchange the permeability of the cell membrane. So we conducted further experiment todetect the change of permeability when the cells of blue molds were treated withjiean-peptide. And the effect of jiean-peptide on non-growing cells of blue molds wastested. By the spectrophotometer measurement, we found that compounds with lightabsorption at 260 nm and 280 nm were released and amounts increased within 12 hcompared with the control. Moreover, by the ICP measurement, the leakage of K+occurred immediately in the presence of jiean-peptide within 1 h, but with nearly nofurther change after 1 h. All these results indicate that jiean-peptide could change themembrane permeability of blue molds immediately and result in leaking nucleotides,proteins and K+ from cells.

Effect of the addition of YAG(Y3Al5O12) nanopowder on the mechanical properties of lanthanum zirconate

La2Zr2O7 (LZ) is a promising thermal barrier coating material for the high-temperature applications, which could be significantly toughened by the YAG nanopowder incorporated into the matrix. The composites of xYAG/(1-x)LZ (Y=10, 15, 20 vol. %, LZ-x-YAG) were densified by means of high-pressure sintering (HPS) under a pressure of 4.5 GPa at 1650 degrees C for 5 min, by which a high-relative density above 93% could be obtained. The morphologies of the fractured surfaces were investigated by the scanning electron microscope, and the fracture toughness and Vicker's-hardness of the composites were evaluated by the microindentation. The grain size of the LZ matrix drops significantly with the addition of YAG nanoparticles and the fracture type changes from the intergranular to a mixture type of the transgranular and intergranular in the nanocomposites. The LZ-20-YAG nanocomposite has a fracture toughness of 1.93 MPa m(1/2), which is obviously higher than that of the pure LZ (1.57 MPa m(1/2)), and the toughening mechanism is discussed in this paper.

Study of hydrogen-bonded blend of polylactide with biodegradable hyperbranched poly(ester amide)

Polylactide (PLA) was melt blended with a biodegradable hyperbranched poly(ester amide) (HBP) to enhance its flexibility and toughness without sacrificing comprehensive performance. The advantage of using HBP was due to its unique spherical shape, low melt viscosity, and abundant functional end groups together with its easy access. Rheological measurement showed that blending PLA with as little as 2.5% HBP resulted in a 40% reduction of melt viscosity. The glass transition temperature (T-g) of PLA in the blends decreased slightly with the increase of HBP content, indicating partial miscibility which resulted from intermolecular interactions via H-bonding. The H-bonding involving CO of PLA with OH and NH of HBP was evidenced by FTIR analysis for the first time. The HBP component, as a heterogeneous nucleating agent, accelerated the crystallization rate of PLA. Remarkably, with the increase of HBP content, the elongation at break of PLA blends dramatically increased without severe loss in tensile strength, even the tensile strength increased within 10% content of HBP. The stress-strain curves and the SEM photos of impact-fractured surface showed the material changed from brittle to ductile failure with the addition of HBP. Reasonable interfacial adhesion via H-bonding and finely dispersed particulate structure of HBP in PLA were proposed to be responsible for the improved mechanical properties.

Independence of the brittle-ductile transition from the rubber particle size for impact-modified poly(vinyl chloride)

A series of acrylic impact modifiers (AIMS) with different particle sizes ranging from 55.2 to 927.0 nm were synthesized by seeded emulsion polymerization, and the effect of the particle size on the brittle-ductile transition of impact-modified poly(vinyl chloride) (PVC) was investigated. For each AIM, a series of PVC/AIM blends with compositions of 6, 8, 10, 12, and 15 phr AIM in 100 phr PVC were prepared, and the Izod impact strengths of these blends were tested at 23 degrees C. For AIMs with particle sizes of 55.2, 59.8, 125.2, 243.2, and 341.1 nm, the blends fractured in the brittle mode when the concentration of AIM was lower than 10 phr, whereas the blends showed ductile fracture when the AIM concentration reached 10 phr. It was concluded that the brittle-ductile transition of the PVC/AIM blends was independent of the particle size in the range of 55.2-341.1 nm. When the particle size was greater than 341.1 nm, however, the brittle-ductile transition shifted to a higher AIM concentration with an increase in the particle size. Furthermore, the critical interparticle distance was found not to be the criterion of the brittle-ductile transition for the PVC/AIM blends.