克拉维酸产生菌的诱变育种与发酵工艺优化研究

以克拉维酸产生菌棒状链霉菌Streptomyces clavuligerus CCRC11518（ATCC 27064）III50为出发菌株, 首先比较各种物理和化学诱变剂处理对其克拉维酸生物合成的影响, 确定了亚硝基胍为棒状链霉菌诱变育种的诱变剂及其处理剂量: 2mg/ml、40min. 经浓度为2mg/ml的亚硝基胍处理40min后, 采用新颖理性化筛选方法, 通过逐步筛选自身代谢产物抗性突变株、克拉维酸抗性突变株和链霉素抗性突变株, 最终得到一株克拉维酸高产菌VI118(效价633μg/ml), 其克拉维酸效价是出发菌株(效价377μg/ml)的167.9%. 该高产突变株在琼脂斜面培养基上连续传接10代, 克拉维酸效价保持稳定. 通过单因子和多因子摇瓶正交试验, 对高产菌株VI118的发酵条件进行了研究, 确定最佳发酵条件: 甘油60g, 水解植物蛋白 60g, KH2PO4 0.5 g, 玉米浆 7.5g, MnSO4•H2O 0.34g, MgSO4•7H2O 0.99g, FeSO4•7H2O 0.56g, 蒸馏1000ml, pH 7.0, 发酵培养基装量20ml/250ml三角瓶, 接种量10％, 培养温度28ºC, 220r/min摇床培养72h后测定效价. 在最佳发酵条件下克拉维酸效价达到651μg/ml, 同时把初始发酵培养基的昂贵成分替换为廉价的工业原料. 通过摇瓶分批补料试验, 得到最佳补料物质和补料方式：在上述最佳发酵条件下, 分别在发酵培养48h、56h、64h、72h时补加4ml无菌水, 80h发酵结束, 克拉维酸效价达到905μg/ml. 在不增加原料成本的情况下通过摇瓶补料方式克拉维酸效价为未补料的139.0％, 总产量为未补料的264％. By a novel rational screening method, mutant Streptomyces clavuligerus CCRC11518（ATCC 27064）III50（titres 377μg/ml）, as the clavulanic acid-producing parent strain, was treated by NTG (2mg/ml) for 40min, and the self-generated metabolites resistant mark, the clavulanic acid resistant mark and the streptomycin resistant mark were added step by step. Finally, the mutant VI118（titres 633μg/ml）with the three marks was obtained. The clavulanic acid productivity of this mutant was increased by 167.9% compared with the parent strain. After reproducing 10 generations on the agar medium slant, the productivity of this mutant was stable. The optimum fermentation conditions were established as followings: glycerol 60g, acid hydrolyzed vegetable protein 60g, KH2PO4 0.5g, corn steep liquor 7.5g, MnSO4•H2O 0.34g, MgSO4•7H2O 0.99g, FeSO4•7H2O 0.56g, distilled water 1 liter, pH 7.0, 20ml in 250ml shake-flask, inoculation 10%(v/v), fermentation temperature 28ºC, rotation speed 220 r/min, time 72h. The clavulanic acid productivity was 651μg/ml, while used the low-priced industrial raw materials. After studying on fed-batch in the shake-flask, the optimum fed-batch manner was obtained: under optimum fermentation conditions, at 48h, 56h, 64h and 72h, adding 4ml distilled water into each flask, fermentation ending at 80h. The clavulanic acid productivity was increased by 139% compared with no fed-batch, meanwhile the total yield was increased by 264%.

三峡永久船闸高边坡开挖三维离散元数值模拟:3-D Simulation of the Excavation of High Steep Slope of Three-Gorges Permanent Lock by Distinct Element Method

采用面一面接触的三维离散元刚性块体模型,从实测节理面中取出其中的三组,按照其倾向、倾角和节理间距将三峡永久船闸未开挖的区域划分为10~5个离散单元,通过施加力边界条件,给出了与实测初始地应力场接近的数值模拟结果；然后,分4步模拟了永久船闸的开挖过程。计算结果表明：开挖过程会引起节理面出现张开趋势,个别岩体还会沿着节理面滑移。岩体位移的不对称现象较为自然地说明了由节理引起的岩体各向异性特征。

Short-pulse laser absorption in very steep plasma density gradients

An analytical fluid model for resonance absorption during the oblique incidence by femtosecond laser pulses on a small-scale-length density plasma [k(0)L is an element of(0.1,10)] is proposed. The physics of resonance absorption is analyzed more clearly as we separate the electric field into an electromagnetic part and an electrostatic part. It is found that the characteristics of the physical quantities (fractional absorption, optimum angle, etc.) in a small-scale-length plasma are quite different from the predictions of classical theory. Absorption processes are generally dependent on the density scale length. For shorter scale length or higher laser intensity, vacuum heating tends to be dominant. It is shown that the electrons being pulled out and then returned to the plasma at the interface layer by the wave field can lead to a phenomenon like wave breaking. This can lead to heating of the plasma at the expanse of the wave energy. It is found that the optimum angle is independent of the laser intensity while the absorption rate increases with the laser intensity, and the absorption rate can reach as high as 25%. (c) 2006 American Institute of Physics.

Molecular and functional characterization of a c-type lysozyme from the Asian corn borer, Ostrinia furnacalis

Some lepidopteran lysozymes have been reported to display activity against Gram-positive and Gram-negative bacteria, in contrast to most lysozymes that are active only against Gram-positive bacteria. OstrinLysC, a c-type lysozyme, was purified from the As

Fast Discrimination of Commerical Corn Varieties Based on Near Infrared Spectra

The existing methods for the discrimination of varieties of commodity corn seed are unable to process batch data and speed up identification, and very time consuming and costly. The present paper developed a new approach to the fast discrimination of varieties of commodity corn by means of near infrared spectral data. Firstly, the experiment obtained spectral data of 37 varieties of commodity corn seed with the Fourier transform near infrared spectrometer in the wavenurnber range from 4 000 to 12 000 cm (1). Secondly, the original data were pretreated using statistics method of normalization in order to eliminate noise and improve the efficiency of models. Thirdly, a new way based on sample standard deviation was used to select the characteristic spectral regions, and it can search very different wavenumbers among all wavenumbers and reduce the amount of data in part. Fourthly, principal component analysis (PCA) was used to compress spectral data into several variables, and the cumulate reliabilities of the first ten components were more than 99.98%. Finally, according to the first ten components, recognition models were established based on BPR. For every 25 samples in each variety, 15 samples were randomly selected as the training set. The remaining 10 samples of the same variety were used as the first testing set, and all the 900 samples of the other varieties were used as the second testing set. Calculation results showed that the average correctness recognition rate of the 37 varieties of corn seed was 94.3%. Testing results indicate that the discrimination method had higher precision than the discrimination of various kinds of commodity corn seed. In short, it is feasible to discriminate various varieties of commodity corn seed based on near infrared spectroscopy and BPR.

三孢布拉氏霉发酵产β-胡萝卜素的研究

本论文研究了利用三孢布拉氏霉(Blakeslea trispora)发酵产β-胡萝卜素的培养条件。主要包括：发酵培养基的确定，发酵条件的优化。还考察了发酵菌丝体中β-胡萝卜素的提取方法及薄层层析等。 首先研究了培养基成分对三孢布拉氏霉发酵产β-胡萝卜素的影响。确立了玉米淀粉作为碳源，黄豆粉（热榨）作为氮源，棉籽油作为植物油的发酵培养基配方，其成分为：玉米淀粉 3％，黄豆粉（热榨） 2％，棉籽油 3％，KH2PO4 0.2%，MgSO4·7H2O 0.2%，维生素B1 0.002％，pH值6.0。 其次，通过比较不同的发酵影响因子，分别得到最适的条件：如三孢布拉氏霉正负菌接种比例为1.3：0.7，培养基pH值为7.0（灭菌后），发酵促进因子为Triton X-100。并采用正交试验法，确定其最佳发酵条件为正负菌接种比例1.3/0.7，发酵培养基pH为7.0，在培养基中添加表面活性基Triton X-100 0.08％。使该菌株产β-胡萝卜素的量达到0.73g/L，较初始发酵条件提高了3.3倍。 研究中还找到一个简便有效的对β-胡萝卜素的提取方法，选用盐酸-热处理法进行细胞破壁，并选用沸程为60～90℃的石油醚进行萃取。 用三孢布拉霉菌丝体内类胡萝卜索的石油醚提取液点样于硅胶G板，以丙酮：石油醚（5：95）为展开剂能将β-胡萝卜素与其它类胡萝卜索分离。该方法简便快速，并有一定实用价值。 The fermentative conditions of β-carotene by Blakeslea trispora have been investigated. These conditions include fermentation medium, the optimization of some fermentation factor. The extracting methods and the TLC of carotenoids were also researched. Firstly, the effects of composition of fermentation medium on the yield of β-carotene were studied. the results showed that the best fermentation medium was corn starch 3％，soybean power 2％，cottonseed oil 3％，KH2PO4 0.2%，MgSO4·7H2O 0.2%，vitamin B1 0.002％，pH value 6.0. Secondly, through compared some factors, such as different proportion of plus and minus strains, pH value, nonionic surfactants, respective best values have been obtained. The best proportion of plus and minus strains is 1.3:0.7, pH value of fermentation medium (sterilized) is 7.0, fermentation accelerant which acts as surfactants is Triton x-100. Farther on, the fermentative conditions were optimized through orthogonal experiment, the optimization showed that proportion of plus and minus strains is 1.3:0.7，pH value is 7.0, content of Triton x-100 is 0.08％. And the yield of β-carotene reached 0.73g/L, which was up to 3.3 times through the fermentation. In the extracting study, it has showed hydrochloric acid-heat treatment is a simple, convenient and effective extracting methods is which was used to destroy the cell wall, and the extracting organic solvent is petroleum ether whose boiling range is 60~90 ℃. In the TLC experiments, extracting contents in the petroleum ether were spotted in the silicagel plate, and the mixed liquor of acetone and petroleum ether (5：95) is developping agent, which can distinguish β-carotene from other carotenoids. It is a simple and quick technique.

Coal-burning roasted corn and chili as the cause of dental fluorosis for children in southwestern China

To find the pathologic cause of the children's dental fluorosis in southwestern China, diet structure before the age of 6 and prevalence rate of dental fluorosis (DF) of 405 children were investigated, and the fluorine and arsenic content of several materials were determined. The prevalence rate of DF of children living on roasted corn before the age of 6 is 100% with nearly 95% having the mild to severe DF; while that of children living on non-roasted corn or rice is less than 5% with all having very mild DF. The average fluorine and arsenic concentration are 20.26 mg/kg and 0.249 mg/kg in roasted corn, which are about 16 times and 35 times more than in non-roasted corn, respectively. The average fluorine concentration is 78 mg/kg in coal, 1116 mg/kg in binder clay and 313 mg/kg in briquette (coal mixed with clay). The average arsenic concentration of coal is 5.83 mg/kg, the binder clay is 20.94 mg/kg, with 8.52 mg/kg in the briquette. Living on roasted corn and chili is the main pathologic cause of endemic fluorosis in southwestern China. The main source of fluorine and arsenic pollution of roasted corn and chill is the briquette of coal and binder clay. (C) 2010 Elsevier B.V. All rights reserved.

Effect of acetylation on the properties of corn starch

Acetylated corn starches with different degrees of substitution (DS 0.85, DS 1.78, DS 2.89) were synthesized by the reaction of corn starch with acetic anhydride in the presence of acetic acid under varying reaction temperatures. The product was characterized by FTIR spectroscopy, H-1 NMR, X-ray diffraction and contact angle measurement. Acid-base titration and H-1 NMR methods were employed to determine the degree of substitution of product. FTIR spectroscopic analysis showed that the characteristic absorption intensities of esterified starch increased with increase in the degree of substitution, and the characterized peak of hydroxyl group almost disappeared in the spectrum of DS 2.89 acetylated starch. The detailed chemical microstructure of native starch and acetylated starch was confirmed by H-1 NMR, C-13 NMR and C-13-(1) H-1 COSY spectra.

Preparation and characterization of cationic corn starch with a high degree of substitution in dioxane-THF-water media

Cationic corn starch derivatives with a high degree of substitution are prepared in alkaline solution or in mixed media of organic solvent and water with different levels of the cationic reagent, 2,3-epoxypropyltrimethylammonium chloride. The starch cationization yield is investigated, and the results indicate that the degree of substitution (DS) of the samples depends on the reaction conditions and reaction media. The maximum DS values are up to 1.37 in 1,4-dioxane alkali ne-aqueous solution. Meanwhile, the structures of the cationic starch derivatives are characterized by elemental analyses, FTIR spectroscopy, X-ray diffraction, and C-13 NMR spectroscopy, as well as by SEM techniques.

Extraction and recovery of cerium(IV) along with fluorine(I) from bastnasite leaching liquor by DEHEHP in [C(8)mim]PF6

BACKGROUND: Ionic liquids (ILs) as environmentally benign solvents have been widely studied in the application of solvent extraction. However, few applications have been successfully industrialized because of the difficult stripping of metal ions or the loss of components of the ILs. More work needs to be done to investigate the extraction behaviour of IL-based extraction systems. In this work, the extraction behaviour of Ce(IV), Th(IV) and some trivalent rare earth (RE) nitrates by di(2-ethylhexyl) 2-ethylhexylphosphonate (DEHEHP) in the IL, 1-methyl-3-octylimidazolium hexafluorophosphate ([C(8)mim]PF6), was investigated and compared with that in the n-heptane system. In particular, the effect of F(I) on the extraction mechanism for Ce(IV) and its separation from Th(IV) was investigated. Otherwise, the recovery efficiency of Ce(IV) and F(I) from a practical bastnasite leach liquor was examined using IL based extraction.

Synthesis of dodecenyl succinic anhydride (DDSA) corn starch

Dodecenly succinic anhydride (DDSA) starches were prepared commercially by the base catalyzed reaction of DDSA in pre-emulsion with starch granular in aqueous slurry. The results indicated that the degree of substitution and reaction efficiency were 0.0256% and 42.7%, respectively, at the parameters for the preparation of DDSA starches in starch slurry 30%, DDSA/starch radio 10% (wt/wt), pH 8.5-9.0, reaction temperature 313 K. After modification, product surface chemical composite had been changed which was prone to migrate into less polar solution. The chemical structural characteristics were investigated by methods of FTIR and H-1 NMR. The results of X-ray diffraction showed the native A-type crystalline pattern, indicating that reaction of corn starch with DDSA caused no change in the crystalline structure. Compared to native starch, the hydrophobic performance of esters was greatly increased. With the DS increasing, contact angles were gradually increased, however, the adhesion works were decreased. The maximum contact angle of DDSA starch could attend to 123 degrees, and the corresponding adhesion work was 33.2 mJ m(-2).

Structure analysis of the fulvic acids extracted from composted corn stalk residue

Chemical structure of fulvic acids extracted from composted corn stalk residue(CSR FA)was studied by Fourier transform infrared (FTIR) spectroscopy, H-1 and C-13 nuclear magnetic resonance(H-1-NMR, C-13-NMR) spectroscopy. The results show that CSR FA mainly consists of four types of carbon: carbonyl, aromatical, alkyl and carbohydrate, the carbohydrate is dominant. Its aromaticity is 15.42%, less than that of CSR HA. This indicates that the construction of CSR FA is simpler than that of CSR HA, FA can not be extracted from undecomposed corn stalk residue. CSR FA may be formed by cellulose or hemicellulosemorties combined with aromatic compound from decomposed lignin.

Pressure Controlled Self-Assembly of High Quality Three-Dimensional Colloidal Photonic Crystals

A concise pressure controlled isothermal heating vertical deposition (PCIHVD) method is developed, which provides an optimal growing condition with better stability and reproducibility for fabricating photonic crystals (PCs) without the limitation of colloidal sphere materials and sizes. High quality PCs are fabricated with PCIHVD from polystyrene spheres with diameters ranging from 200 nm to 1 mu m. The deep photonic band gap and steep photonic band edge of the samples are most favorable for realizing ultrafast optical devices, photonic chips, and communications. This method makes a meaningful advance in the quality and diversity of PCs and greatly promotes their wide applications.

The Fluid Phenomena In the Crystallization Of the Protein Crystal

This paper reports that an optical diagnostic system consisting of Mach-Zehnder interferometer with a phase shift device and image processor has been used for study of the kinetics of protein crystal growing process. The crystallization process of protein crystal by vapour diffusion is investigated. The interference fringes are observed in real time. The present experiment demonstrates that the diffusion and the sedimentation influence the crystallization of protein crystal which grows in solution, and the concentration capillary convection associated with surface tension occurs at the vicinity of free surface of the protein mother liquor, and directly affects on the outcome of protein crystallization. So far the detailed analysis and the important role of the fluid phenomena in protein crystallization have been discussed a little in both space- and ground-based crystal growth experiments. It is also found that these fluid phenomena affect the outcome of protein crystallization, regular growth, and crystal quality. This may explain the fact that many results of space-based investigation do not show overall improvement.