碱法草浆造纸蒸煮黑液厌氧生物降解性及其主要微生物类群研究

造纸行业是造成我国水环境有机污染物的重要污染源之一，其水污染的特点是小厂多、草浆多、工艺落后、污染扩散面广、造成废 水排放量大，每年排放的废水量约39亿立方米，占全国工业废水排放量的1/6，其中有机污染物（以BOD5计）160万吨左右，约占全 国工业废水中有机污染物总量的1/4。尤以占全国制浆造纸行业90%以上的碱法草浆造纸厂的蒸煮黑液量大面广，除含有机物外，还 含有木质素、残碱、硫化物、氯化物等污染物，属于PH值高、色度深、难于治理的高浓度有机废水，对水体污染特别严重，各地要 求治理呼声很高，急待研究并尽快找出各种有效的治理途径。对于碱法草浆蒸煮，黑液高浓度废水的治理，有各种方法，根据国内 的研究进展和我们已有试验工作表明，最经济有效，具有实用价值，在生产上可获得成功是厌氧处理法。近10多年来，国外关于高 效厌氧处理技术研究进展迅速，并出现了多种多样的工艺设备，如高效厌氧生物反应器，并在实用化方面取得了很大成绩，建立了 生产性装置，达到了高负荷运行，效果良好。本试验是根据我们已有研究基础，针对我国国情，对小型制浆造纸厂水污染防治除了 开发碱回收及各种综合利用技术外，要特别加强废水(废液)实用技术研究的指导思想，本试验采用改进型的上流式厌氧污泥床反应 器，设计了两种试验方案，通过试验结果如下。1. 试验方案I—碱法草浆黑液酸化和厌氧发酵I号UASB反应器动态模型试验结果表 明：(1). 采用中温35℃±1℃高效厌氧反应器USAB内装有填料(陶粒)和三相分离器，具有保持高浓度生物量和防止污泥流失的特点 ，污泥浓度Vs 可达30%以上，因而具有高效、节能、产能、滞留期短的优点，当进水CODcr在7500-10000mg/l，HRT由7天缩短到3天 ，有机容积负荷在1.22gCODcr/l·d-3.43gCODcr/l·d时，CODcr平均去除率可达55%-45.5%，最高CODcr去除率可达60.2-63.5%， BOD5去除率可达75.9-83.2%,沼气容积产气率可达0.29-0.67l/l·d，每克CODcr转化为沼气产率达0.39-0.48l/gCODcr·d，CH4含量 65.8-75.5%。厌氧发酵出水再用化学法进行后处理脱除难降解的木质素，CODcr总去除率达80%以上。(2). 动态试验结果表明：采 用酸化—厌氧发酵处理黑液工艺合理，技术路线可行。2. 试验方案II—黑液用化学法(Hcl)去除木质素进行厌氧发酵，II号UASB反 应器动态模型试验结果表明：(1). 采用中温35℃±1℃高效厌氧反应器UASB(内有软填料)，当进水CODcr7000-13000mg/l左右，HRT 由6天缩短到1天，有机负荷由0.98gCODcr/l·d增加到11gCODcr/l·d时，COD平均去除率均可稳定在70-77%，BOD5去除率为87.3- 93.1%，沼气容积产气率0.21-2.6l/l·d，每克CODcr转化为沼气产率为0.39-0.48l/gCODcr·d，高的可达0.53l/gCODcr·d，转化 率较高，CH4含量63-70%。(2). 试验证明碱法草浆黑液物化预处理—厌氧发酵处理的技术路线也是可行的，工艺合理、效果较好。 在有条件的工厂可采用。3.厌氧发酵阶段几大类群微生物计数表明：(1). 当发酵工艺和运行处于相对稳定状态时，微生物群体的 组成也达到相对的稳定，各类微生物之间保持动态平衡关系。当产乙酸菌的数量为107-108个/ml时，产甲烷菌的数量为105-106 个/ml，当产乙酸菌数量为106-107个/ml时，产甲烷菌的数量为103-105个/ml。(2).稳态运行条件下，黑液预处理为甲烷发酵创造 了有利的生态环境，获得了较好的处理效果和较高的COD转化为沼气的产率0.39-0.48l/g·CODcr·d，反应器中形成较为稳定而数 量较下水污泥中高1-2个数量级的厌氧发酵微生物区系组成。这一结果为黑液厌氧发酵提供了微生物理论依据。Paper industry is one of the important pollution source of water environment in our country. Its character of water pollution is many small factories, much grass pulp, disadvantageous technique, large preading area of pullution. Its effluent makes up 1/6 of whole country's industry wastwater. Its organic pollutant accounts 1/4 of whole country's. Alkaline grass paper pulp effluent with pollutants such as ligoin, remaining alkali sulfide, chloride besides organic material, is a kind of high concentrate organic wastewater which has high PH walug, dark colour and is difficult in treatment. There is urgent require to find ways to treat the wastewater. There are different ways to treat alkaline paper grass pulp effluent. According to the research advances and our experiment work, the most economical and useful way is anaerobic degradation which was advanced quick in last ten years. In the control of waste water of small pulp paper mill, the study of wastewater utilization technology should be emphasized, besides alkaline retrieving and different kinds of comprehensive utilization technology. Our experiment used modified UASB(Upflow Anaerobic Sludge Blanket Reactor). Two kinds of plan were disgned. The results are lined below. 1. The first experiment plant-aciding black pulp effluent and methanogenic digestion. The dynamic model experiment results of I-UASB reactor showed: (1)The mesophilic(35℃±1℃)high effect UASB reactor having haydite and threee state seperation in it had the character of keeping high bioimass concentration and preventing losss of sludge. It had advantages of high effect, energe saving, energe prodcing and short HRT(Hydroulic retention time). When the influent COD was 7500-10000mg, HRT was shortened from 7 days to 3days, organic loading rate was 1.22g-3.43COD/l· d, the average COD removal efficiency was 55%-45%. The highest COD efficiency was 60.2-63.5%, BOD removal of 75.9 -83.4% was achieved. Biogass production rate were up to 0.29-0.67l/l·d. Biogass converted efficiency from every gram of COD could reach 0.39-0.48l/gCOD·d. Methane content was 65.0-75.5%. Chemical method was used to deplate lignin in anaerobic digestion effluent. Total COD removal efficiency could be more than 80%. (2)Using aciding annaerobic digestion to treat the black effluent was reseanable in technique and technology. 2. The second experiment plan-anaerobic digestion was used after the chemical method was used to deplate lignin in the black effluent. The result of dynamic experiment of II-UASB reactor showed: (1)High effect mesophilic (35℃±1℃)UASB reactor having soft slaffing in was used. When influent COD was about 7000-13000mg/l, HRT was shortened from 6 days to 1 day and organic loading rate was increased from 0.90 to 11g COD /l·d, average COD removal efficiency remained stable on 70-77%. BOD, removal efficiency was between 87.3-93.1%. Biogass production rate was 0.2-2.6l/l ·d .Biogass converted efficiency from a gram of COD was 0.39-0.481/gCOD·d with the high value of 0.53l/gCOD·d. Methane content was 63-70%. (2)The way that using physical, chemical Pre-treatment-anaerobic digestion to treat alkaline black effluent is feasible and can be used in some factories when the condition exists. 3. Counting of several class of microoganisms in anaerobic digestion stage showed: (1)As the disgestion was in stable motion, the compositon of microorganic colony could get relative stable. Dynamic balance was remaining among different kinds of microorganism such as methanogenic bacteria, Acidogenic bacteria, sulfate reducing bacteria, and heterotrophic bacteria. (2)Under stable motion, the pre-treatment of black effluent produced favourable eco-enviroment for methanegenic digestion. Good treatment effect and high biogass convertent efficiency from COD(0.39-0.48l/g·COD· d)were gotten. Some stable and high quantity(10-100times more than sewage sludge)microorganism colony were formed in the reactor. This result provided theoretical basis for anaerobic digestion of black effluent.

A second-order dynamic subgrid-scale stress model

A second-order dynamic model based on the general relation between the subgrid-scale stress and the velocity gradient tensors was proposed. A priori test of the second-order model was made using moderate resolution direct numerical simulation date at high Reynolds number ( Taylor microscale Reynolds number R-lambda = 102 similar to 216) for homogeneous, isotropic forced flow, decaying flow, and homogeneous rotating flow. Numerical testing shows that the second-order dynamic model significantly improves the correlation coefficient when compared to the first-order dynamic models.

The effect of the group delay ripple of chirped fiber grating on composite second-order in optical fiber CATV system

The effect of group delay ripple of chirped fiber gratings on composite second-order (CSO) performance in optical fiber CATV system is investigated. We analyze the system CSO performances for different ripple amplitudes, periods and residual dispersion amounts in detail. It is found that the large ripple amplitude and small ripple period will deteriorate the system CSO performance seriously. Additionally, the residual dispersion amount has considerable effect on CSO performance in the case of small ripple amplitude and large ripple period. (c) 2004 Elsevier B.V. All rights reserved.

Composite second-order performance improvement in optical fibre CATV transmission system using chirped fibre grating

Theoretically, we analyse the dispersion compensation characteristics of the chirped fibre grating (CFG) in an optical fibre cable television (CATV) system and obtain the analytic expression of the composite second-order (CSO) distortion using the time-domain form of the field envelope wave equation. The obtained result is in good agreement with the numerical simulation result. Experimentally, we verify the result by making use of the tunable characteristics of CFG to change the dispersion compensation amount and obtain an optimal CSO performance in a 125km fibre transmission link. Both the theoretical and experimental results show that the CSO performance can be improved by properly choosing the dispersion compensation amount for a certain fibre transmission link.

Analysis of a second-order polarization-independent filter made of a single ring resonator and a Sagnac interferometer

A novel second-order polarization-independent filter made of a single ring resonator and a Sagnac interferometer (SRRSI) is proposed, and its filtering characteristics are investigated. By using birefringence in waveguide, a single ring resonator can be used to synthesize a filter with second-order response. Analytical formulas are derived for characteristics of the SRRSI varied with waveguide parameters.. such as the coupling coefficient; and the critical condition of a second-order Butterworth filter is given. The influence of loss in the ring resonator is also analyzed. (c) 2005 Elsevier B.V. All rights reserved.

Measuring ultrashort optical pulses using multi-shot second harmonic generation frequency resolved optical gating

Frequency resolved optical gating (FROG), is an effective technique for characterizing the ultrafast laser pulses. The multi-shot second harmonic generation (SHG) FROG is the most sensitive one in different FROGs. In this paper we use this technique to measure the femtosecond optical pulses generated by a conventional Ti:sapphire oscillator.

Beam splitting of low-contrast binary gratings under second Bragg angle incidence

Beam splitting of low-contrast rectangular gratings under second Bragg angle incidence is studied. The grating period is between lambda and 2 lambda. The diffraction behaviors of the three transmitted propagating orders are illustrated by analyzing the first three propagating grating modes. From a simplified modal approach, the design conditions of gratings as a high-efficiency element with most of its energy concentrated in the -2nd transmitted order (similar to 90%) and of gratings as a 1 x 2 beam splitter with a total efficiency over 90% are derived. The grating parameters for achieving exactly the splitting pattern by use of rigorous coupled-wave analysis verified the design method. A 1 x 3 beam splitter is also demonstrated. Moreover, the polarization-dependent diffraction behaviors are investigated, which suggest the possibility of designing polarization-selective elements under such a configuration. The proposed concept of using the second Bragg angle should be helpful for developing new grating-based devices. (C) 2008 Optical Society of America.

Influence of the second cladding on the properties of four-layer large flattened mode fibers

A theoretical method to analyze four-layer large flattened mode (LFM) fibers is presented. The influence of the second cladding on the properties of four-layer LFM fiber, including the fundamental and higher-order modal fields, effective area, bending loss, and dispersion, are studied by comparison. At the same time, the reasons for the different characteristics are considered. The obtained results indicate that the effective area of the four-layer LFM fiber is about 1.6 times larger than that of the conventional standard step-index fiber and the fibers have better bend-induced filtering ability than three-layer LFM fibers. (C) 2007 Society of Photo-Optical Instrumentation Engineers.

Influence of the second cladding on the properties of four-layer large flattened mode fibers

A theoretical method to analyze four-layer large flattened mode (LFM) fibers is presented. The influence of the second cladding on the properties of four-layer LFM fiber, including the fundamental and higher-order modal fields, effective area, bending loss, and dispersion, are studied by comparison. At the same time, the reasons for the different characteristics are considered. The obtained results indicate that the effective area of the four-layer LFM fiber is about 1.6 times larger than that of the conventional standard step-index fiber and the fibers have better bend-induced filtering ability than three-layer LFM fibers. (C) 2007 Society of Photo-Optical Instrumentation Engineers.

Second-harmonic generation in Ge20As25S55 glass irradiated by an electron beam

Second-harmonic generation was observed in Ge(20)AS(25)S(55) chalcogenide glass irradiated by an electron beam. The second-harmonic intensity increased with increasing electron-beam current and accelerating voltage. The second-harmonic generation in Ge20As25S55 glass was caused by the space-charge electrostatic field that was generated by irradiation of an electron beam. Second-order nonlinearity chi ((2)) as great as 0.8 pm/V was obtained. The results of measurements of thermally stimulated depolarization current indicated that the glass was poled in the thin layers of its surface (several micrometers) and that the nonlinearity was stable. (C) 2001 Optical Society of America.

Modelling and simulation of the second-order Doppler error of a laser dual-frequency interferometer

Only the first- order Doppler frequency shift is considered in current laser dual- frequency interferometers; however; the second- order Doppler frequency shift should be considered when the measurement corner cube ( MCC) moves at high velocity or variable velocity because it can cause considerable error. The influence of the second- order Doppler frequency shift on interferometer error is studied in this paper, and a model of the second- order Doppler error is put forward. Moreover, the model has been simulated with both high velocity and variable velocity motion. The simulated results show that the second- order Doppler error is proportional to the velocity of the MCC when it moves with uniform motion and the measured displacement is certain. When the MCC moves with variable motion, the second- order Doppler error concerns not only velocity but also acceleration. When muzzle velocity is zero the second- order Doppler error caused by an acceleration of 0.6g can be up to 2.5 nm in 0.4 s, which is not negligible in nanometric measurement. Moreover, when the muzzle velocity is nonzero, the accelerated motion may result in a greater error and decelerated motion may result in a smaller error.