Modeling and Simulation of Liquid Pulsed Particulate Fluidized Beds

Pulsed fluidization is of considerable interest in process engineering for improving fluidization quality. Quantitative understanding of the pulsed two-phase flow behaviors is very important for proper design and optimum operation of such contactors. The

Demulsification of emulsions exploited by enhanced oil recovery system

Experimental data are presented to show the influence of the enhanced oil recovery system's components, alkali, surfactant, and polymer, on the demulsification and light transmittance of the water separated from the emulsions. Among which, the effects of surfactants, polyoxyethylene (10) alkylphenol ether (OP-10) and sodium petroleum sulfonate (CY-1) on emulsion stability, are the strongest of any component, the effects of polymer, hydrolytic polyacrylamide (HPAM) 3530S, on emulsion stability are the weakest. This research also suggests a possible emulsion minimization approach, which could be implemented in refineries utilizing microwave radiation. Compared with conventional heating, microwave radiation can effectively enhance the demulsification rate by an order of magnitude and increase the light transmittance of the water separated from the emulsions. The demulsification efficiency may reach 100% in a very short. time under microwave radiation.

A Research on New Method of Transportation Technics for Heavy Oil and Practice in Oil Field

介绍一种可应用于高粘度稠油管输的新工艺。即用自行研制的蒸汽引射器采用无界引射方式,将蒸汽直接注入到输油管道中,利用蒸汽释放的热量提高稠油温度降低粘度,从而达到降低稠油输送压降的目的,它比间接加热输送工艺所用的蒸汽量或耗煤量大大减少。方法在辽河油田输油管线上进行了工业现场试验,取得了很好的效果。

孤岛油田曲流河微相单砂体储层建筑结构及挖潜方向研究

In the intermediary and later stage of oil field development, remaining oil disperses fiercely, the contradiction in the layer has become the main problem and the distribution of remaining oil is transforming to the difference of single sand-body. So, the fine description research of reservoir is becoming a tendency and the methods of remaining oil research need new developments. In the research of “The Single-sand-body Architectural Element and Potentiality Analysis Research of Meandering River, GuDao Oil Field”, the research principle is analytical hierarchy process and schema prescription what are reservoir fine description methods under the condition of dense well pattern. The knowledge of regional sedimentary system and sedimentary facies is the foundation of this research. According to the 3D distribution model of the microfacies sand-body of fluvial facies, stratigraphic unit classification & coenocorrelation of 154 wells are completed in the research of meandering river sand-body in Ng3-4. In this research, the 3D distribution of microfacies sand-body in the main layers are settled. The architectural element model of Ng4 point bar is analysed using the drill core and FMI data. According to the overgrow model of point bar, the surfaces of lateral accretion is traced and the architectural element model of point bar is settled. In the research, the control of micro-facies sand-body of meandering river to the distribution of remaining oil is analysed and the potential area is proposed. All these will play an important role in the development of GuDao oil field. In this research, abundant of logging data, drill core data and production performance data are used to analyse the contributing factor of single sand-body in the Ng3-4 meandering river. Using the technology of geological modeling, all that are researched including the 3D distribution scales of meandering river point bar, the control affection of inner lateral accretion layer to the distribution of oil & gas and remaining. Then, the way of remaining oil development in the sand-body of meandering river is improved. The innovation of the research technology includes (1) the presentation of the conception and research methods of micro-facies sand-body (2) enriching the content of reservoir architectural element research and (3) to renew the research method of remaining oil analysis. The research has practiced with obvious effect.(1)It is deepened into understand the river facies reservoir construction of Gudao oil field, By Building the reservoir construction and studying the effect of diffent deposit or geological interface to fluid partition and to the distribution of the remaining oil, we improved the understanding to the distribution of the remaining oil���(2)By building the distribution mod of the remaining oil in the reservoir construction and making the remaining oil description detailed,the development direction of old oil field is more clear；(3)Expanded the application scales of the horizontal well and enhanced the application effects of the horizontal well technique , we designed and drilled 23 ports horizontal wells in all , the cumulative hydrocarbon production is 10.6*104 t；(4) According to the findings of the internal building structure in reservoir of the fluvial facies in the region of interest, and uniting the injection/production corresponding states、the producing history and the dynamic monitoring documents of the oil/water wells in the flooding units , we researched the residual oil distribution in the point bar , and found the distribution regular patterns of the remaining oil, and comprehended the distribution of the remaining oil . In base of that , we proceeded the optimizing designs of the oil well potentialities , and advanced the effect of the treatment potentials . It is proved that , it was very important that internal building structure research of the single sand body of reservoir for guiding the high efficiency potentialities of the remaining oil in the high water cut stage .

Effect of Rock Mass Structure and Block Size on the Slope Stability-Physical Modeling and Discrete Element Simulation

This paper studies the stability of jointed rock slopes by using our improved three-dimensional discrete element methods (DEM) and physical modeling. Results show that the DEM can simulate all failure modes of rock slopes with different joint configurations. The stress in each rock block is not homogeneous and blocks rotate in failure development. Failure modes depend on the configuration of joints. Toppling failure is observed for the slope with straight joints and sliding failure is observed for the slope with staged joints. The DEM results are also compared with those of limit equilibrium method (LEM). Without considering the joints in rock masses, the LEM predicts much higher factor of safety than physical modeling and DEM. The failure mode and factor of safety predicted by the DEM are in good agreement with laboratory tests for any jointed rock slope.

Parton energy loss in heavy-ion collisions via direct-photon and charged-particle azimuthal correlations

Charged-particle spectra associated with direct photon (gamma(dir)) and pi(0) are measured in p + p and Au + Au collisions at center-of-mass energy root(S)(NN) = 200 GeV with the STAR detector at the Relativistic Heavy Ion Collider. A shower-shape analysis is used to partially discriminate between gamma(dir) and pi(0). Assuming no associated charged particles in the gamma(dir) direction ( near side) and small contribution from fragmentation photons (gamma(frag)), the associated charged-particle yields opposite to gamma(dir) (away side) are extracted. In central Au + Au collisions, the charged-particle yields at midrapidity (vertical bar eta vertical bar < 1) and high transverse momentum (3 < (assoc)(PT) < 16 GeV/c) associated with gamma(dir) and pi(0) (vertical bar eta vertical bar < 0.9, 8 < (trig)(PT) < 16 GeV/c) are suppressed by a factor of 3-5 compared with p + p collisions. The observed suppression of the associated charged particles is similar for gamma(dir) and pi(0) and independent of the gamma(dir) energy within uncertainties. These measurements indicate that, in the kinematic range covered and within our current experimental uncertainties, the parton energy loss shows no sensitivity to the parton initial energy, path length, or color charge.

Modeling and optimization for separation of ionic solutes in pressurized flow capillary electrochromatography

By manipulation of applied pressure or voltage, pressurized flow capillary electrochromatography (P-CEC) permits unique control of selectivity for ionic solutes. A simple mathematical model has been developed to describe the quantitative relationship between the electrochromatographic retention factor (k(*)) of charged solutes and the applied voltage and pressure. The validity of the model was verified experimentally with hydrophilic interaction mode CEC (HI-CEC). On the basis of the model developed, it was found that the value of k(*) could be predicted accurately using only a limited number of data points from the initial experiments at different voltages or pressures. Correlation between the experimentally measured and calculated k(*) was excellent, with a correlation coefficient greater than 0.999. Optimization for the separation of peptides by P-CEC was also performed successfully on the basis of the proposed model.

Modeling and mesoscopic damage constitutive relation of brittle short-fiber-reinforced composites

Aimed at brittle composites reinforced by randomly distributed short-fibers with a relatively large aspect ratio, stiffness modulus and strength, a mesoscopic material model was proposed. Based on the statistical description, damage mechanisms, damage-induced anisotropy, damage rate effect and stress redistribution, the constitutive relation were derived. By taking glass fiber reinforced polypropylene polymers as an example, the effect of initial orientation distribution of fibers, damage-induced anisotropy, and damage-rate effect on macro-behaviors of composites were quantitatively analyzed. The theoretical predictions compared favorably with the experimental results.

Experimental study and simulation principles of an oil-gas multiphase transportation system

Presented is an experimental study on the performance of an oil-gas multiphase transportation system, especially on the multiphase flow patterns, multiphase pumping and multiphase metering of the system. A dynamic simulation analysis is conducted to deduce simulation parameters of the system and similarity criteria under simplified conditions are obtained. The reliability and feasibility of two-phase flow experiment with oil and natural gas simulated by water and air are discussed by using the similarity criteria.

Modeling, numerical methods, and simulation for particle-fluid two-phase flow problems

In this paper, we study the issues of modeling, numerical methods, and simulation with comparison to experimental data for the particle-fluid two-phase flow problem involving a solid-liquid mixed medium. The physical situation being considered is a pulsed liquid fluidized bed. The mathematical model is based on the assumption of one-dimensional flows, incompressible in both particle and fluid phases, equal particle diameters, and the wall friction force on both phases being ignored. The model consists of a set of coupled differential equations describing the conservation of mass and momentum in both phases with coupling and interaction between the two phases. We demonstrate conditions under which the system is either mathematically well posed or ill posed. We consider the general model with additional physical viscosities and/or additional virtual mass forces, both of which stabilize the system. Two numerical methods, one of them is first-order accurate and the other fifth-order accurate, are used to solve the models. A change of variable technique effectively handles the changing domain and boundary conditions. The numerical methods are demonstrated to be stable and convergent through careful numerical experiments. Simulation results for realistic pulsed liquid fluidized bed are provided and compared with experimental data. (C) 2004 Elsevier Ltd. All rights reserved.

Control of Large-size SiC Growth Process Using Modeling tool

Large size bulk silicon carbide (SiC) crystals are commonly grown by the physical vapor transport (PVT) method. The PVT growth of SiC crystals involves sublimation and condensation, chemical reactions, stoichiometry, mass transport, induced thermal stress, as well as defect and micropipes generation and propagation. The quality and polytype of as-grown SiC crystals are related to the temperature distribution inside the growth chamber during the growth process, it is critical to predict the temperature distribution from the measured temperatures outside the crucible by pyrometers. A radio-frequency induction-heating furnace was used for the growth of large-size SiC crystals by the PVT method in the present study. Modeling and simulation have been used to develop the SiC growth process and to improve the SiC crystal quality. Parameters such as the temperature measured at the top of crucible, temperature measured at the bottom of the crucible, and inert gas pressure are used to control the SiC growth process. By measuring the temperatures at the top and bottom of the crucible, the temperatures inside the crucible were predicted with the help of modeling tool. SiC crystals of 6H polytype were obtained and characterized by the Raman scattering spectroscopy and SEM, and crystals of few millimeter size grown inside the crucible were found without micropipes. Expansion of the crystals were also performed with the help of modeling and simulation.

Molecular Modeling and Affinity Determination of scFv Antibody: Proper Linker Peptide Enhances Its Activity

One of existing strategies to engineer active antibody is to link VH and VL domains via a linker peptide. How the composition, length, and conformation of the linker affect antibody activity, however, remains poorly understood. In this study, a dual approach that coordinates molecule modeling, biological measurements, and affinity evaluation was developed to quantify the binding activity of a novel stable miniaturized anti-CD20 antibody or singlechain fragment variable (scFv) with a linker peptide. Upon computer-guided homology modeling, distance geometry analysis, and molecular superimposition and optimization, three new linker peptides PT1, PT2, and PT3 with respective 7, 10, and 15 residues were proposed and three engineered antibodies were then constructed by linking the cloned VH and VL domains and fusing to a derivative of human IgG1. The binding stability and activity of scFv-Fc chimera to CD20 antigen was quantified using a micropipette adhesion frequency assay and a Scatchard analysis. Our data indicated that the binding affinity was similar for the chimera with PT2 or PT3 and ~24-fold higher than that for the chimera with PT1, supporting theoretical predictions in molecular modeling. These results further the understanding in the impact of linker peptide on antibody structure and activity.

Physical Modeling And Parametric Study On Two-Degree-Of-Freedom Viv Of A Cylinder Near Rigid Wall

Unlike most previous studies on the transverse vortex-induced vibration(VIV) of a cylinder mainly under the wallfree condition (Williamson & Govardhan,2004),this paper experimentally investigates the vortex-induced vibration of a cylinder with two degrees of freedom near a rigid wall exposed to steady flow.The amplitude and frequency responses of the cylinder are discussed.The lee wake flow patterns of the cylinder undergoing VIV were visualized by employing the hydrogen bubble technique.The effects of the gap-to-diameter ratio (e0/D) and the mass ratio on the vibration amplitude and frequency are analyzed.Comparisons of VIV response of the cylinder are made between one degree (only transverse) and two degrees of freedom (streamwise and transverse) and those between the present study and previous ones.The experimental observation indicates that there are two types of streamwise vibration,i.e.the first streamwise vibration (FSV) with small amplitude and the second streamwise vibration (SSV) which coexists with transverse vibration.The vortex shedding pattem for the FSV is approximately symmetric and that for the SSV is alternate.The first streamwise vibration tends to disappear with the decrease of e0/D.For the case of large gap-to-diameter ratios (e.g.e0/D = 0.54～1.58),the maximum amplitudes of the second streamwise vibration and transverse one increase with the increasing gapto-diameter ratio.But for the case of small gap-to-diameter ratios (e.g.e0/D = 0.16,0.23),the vibration amplitude of the cylinder increases slowly at the initial stage (i.e.at small reduced velocity V,),and across the maximum amplitude it decreases quickly at the last stage (i.e.at large Vr).Within the range ofthe examined small mass ratio (m＜4),both streamwise and transverse vibration amplitude of the cylinder decrease with the increase of mass ratio for the fixed value of V,.The vibration range (in terms of Vr ) tends to widen with the decrease of the mass ratio.In the second streamwise vibration region,the vibration frequency of the cylinder with a small mass ratio (e.g.mx = 1.44) undergoes a jump at a certain Vr,.The maximum amplitudes of the transverse vibration for two-degree-of-freedom case is larger than that for one-degree-of-freedom case,but the transverse vibration frequency of the cylinder with two degrees of freedom is lower than that with one degree of freedom (transverse).