Distribution of CCR2-64I and SDF1-3 ' A alleles and HIV status in 7 ethnic populations of Cameroon

Limited information is available on the prevalence among rural Africans of host genetic polymorphisms conferring resistance to HIV-1 infection or slowing HIV disease progression.We report the allelic frequencies of the AIDS-related polymorphisms CCR2-64I, SDF1-3#A, and CCR5-D32 in 321 volunteers from 7 ethnic groups in Cameroon. Allelic frequencies differed among the 7 ethnic groups, ranging from 10.8% to 31.3% for CCR2-64I and 0.0% to 7.1% for SDF1-3#A. No CCR5-D32 alleles were found. HIV seroprevalence was 6.9% in the total population and peaked at younger ages in girls and women than in boys and men. Among 15- to 54-year-olds, HIV seroprevalence varied from 2.0% to 11.1% among the village populations. Conditional logistic regression analysis using data from boys and men aged 15 to 54 years showed the number of CCR2-64I alleles to be a significant risk factor for HIV seropositivity (odds ratio per allele adjusted for age and matched on ethnic group = 6.3, 95% confidence interval: 1.3–30.3); this association was not found in women. The findings are consistent with the hypothesis that CCR2-64I alleles may delay HIV disease progression without affecting susceptibility to infection among men. We did not observe this relation among women, and other factors, such as multiple pregnancies or maternal stressors (eg, breastfeeding), may have masked any protective effect of CCR2-64I alleles. Further study of this issue among women is warranted. SDF1-3#A did not differ between HIV-seropositive and HIV-seronegative individuals but wasassociated with increasing age among HIV-seronegative women, suggesting a protective effect against HIV-1 infection.

Probabilistic distribution of one-phase structure seminvariants for an isomorphous pair of structures: Theoretical basis and initial applications

Given a special type of triplet of reciprocal-lattice vectors in the monoclinic and orthorhombic systems, there exist eight three-phase structure seminvariants (3PSSs) for a pair of isomorphous structures. The first neighborhood of each of these 3PSSs is defined by the six magnitudes and the joint probability distribution of the corresponding six structure factors is derived according to Hauptman's neighborhood principle. This distribution leads to the conditional probability distribution of each of the 3PSSs, assuming as known the six magnitudes in its first neighborhood. The conditional probability distributions can be directly used to yield the reliable estimates (0 or pi) of the one-phase structure seminvariants (1PSSs) in the favorable case that the variances of the distributions happen to be small [Hauptman (1975). Acta Cryst. A31, 680-687]. The relevant parameters in the formulas for the monoclinic and orthorhombic systems are given in a tabular form. The applications suggest that the method is efficient for estimating the 1PSSs with values of 0 or pi.

Burst Detection in Turbulent Channel Flows Based on Large Eddy Simulation Databases

Reliable turbulent channel flow databases at several Reynolds numbers have been established by large eddy simulation (LES), with two of them validated by comparing with typical direct numerical simulation (DNS) results. Furthermore, the statistics, such as velocity profile, turbulent intensities and shear stress, were obtained as well as the temporal and spatial structure of turbulent bursts. Based on the LES databases available, the conditional sampling methods are used to detect the structures of burst events. A method to deterimine the grouping parameter from the probability distribution function (pdf) curve of the time separation between ejection events is proposed to avoid the errors in detected results. And thus, the dependence of average burst period on thresholds is considerably weakened. Meanwhile, the average burst-to-bed area ratios are detected. It is found that the Reynolds number exhibits little effect on the burst period and burst-to-bed area ratio.

Intensity Distribution Design for Laser-Induced Thermal Loading Based on Numerical Simulation

To accomplish laser-induced thermal loading simulation tests for pistons,the Gaussian beam was modulated into multi-circular beam with specific intensity distribution.A reverse method was proposed to design the intensity distribution for the laser-induced thermal loading based on finite element(FE) analysis.Firstly,the FE model is improved by alternating parameters of boundary conditions and thermal-physical properties of piston material in a reasonable range,therefore it can simulate the experimental resul...

Effects of the orientation of microgravity on the concentration distribution in crystallization from solution

A quasi-steady state growth and dissolution in a 2-D rectangular enclosure is numerically investigated. This paper is an extension to indicate the effects of the orientation of gravity on the concentration field in crystallization from solution under microgravity, especially on the lateral non-uniformity of concentration distribution at the growth surface. The thermal and solute convection are included in this model.

Numerical Simulation of the Flow Field and Concentration Distribution in the Bulk Growth of Silicon Carbide Crystals

The physical vapor transport (PVT) method is being widely used to grow large-size single SiC crystals. The growth process is associated with heat and mass transport in the growth chamber, chemical reactions among multiple species as well as phase change at the crystal/gas interface. The current paper aims at studying and verifying the transport mechanism and growth kinetics model by demonstrating the flow field and species concentration distribution in the growth system. We have developed a coupled model, which takes into account the mass transport and growth kinetics. Numerical simulation is carried out by employing an in-house developed software based on finite volume method. The results calculated are in good agreement with the experimental observation.

Concentration distribution in solution crystal growth: effect of moving interface conditions

The linear diffusion-reaction theory with finite interface kinetics is employed to describe the dissolution and the growth processes. The results show that it is imperative to consider the effect of the moving interfaces on the concentration distribution at the growth interface for some cases. For small aspect ratio and small gravity magnitude, the dissolution and the growth interfaces must be treated as the moving boundaries within an angle range of 0 degrees < gamma < 50 degrees in this work. For large aspect ratio or large gravity magnitude, the effect of the moving interfaces on the concentration distribution at the growth interface can be neglected except for gamma < - 50 degrees.

Water Content Distribution in the Surface Layer of Maoping Slope

The water content distribution in the surface layer of Maoping slope has been studied by testing the water content at 31 control sites. The water content profiles at these sites have also been determined. The water content distributions at different segments have been obtained by using the Kriging method of geostatistics. By comparing the water content distributions with the landform of the slope, it was shown that the water content is closely dependent on the landform of the slope. The water content distribution in the surface layer provided a fundamental basis for landslide predication and treatment.

Thermodynamical versus log-Poisson distribution in turbulence

The thermodynamical model of intermittency in fully developed turbulence due to Castaing (B. Castaing, J. Phys. II France 6 (1996) 105) is investigated and compared with the log-Poisson model (Z-S, She, E. Leveque, Phys. Rev. Lett. 72 (1994) 336). It is shown that the thermodynamical model obeys general scaling laws and corresponds to the degenerate class of scale-invariant statistics. We also find that its structure function shapes have physical behaviors similar to the log-Poisson's one. The only difference between them lies in the convergence of the log-Poisson's structure functions and divergence of the thermodynamical one. As far as the comparison with experiments on intermittency is concerned, they are indifferent.

Effects on Dense-phase Zone Temperature of Fluidized Bed with Uneven Air Distribution

由于采用非均匀布风,内旋流流化床的移动区空气量不足,导致燃烧不充分,温度较低。当移动区未流化时,密相区内存在较明显的温度不均匀性。随着移动区流速的提高,温度差迅速减小。当移动区流速超过2.0#mu#m后,密相区温度基本均匀一致。流动区流速对密相区温度均匀有一定的影响,流速越高,温度越均匀。

In situ formation by laser cladding of a TiC composite coating with a gradient distribution

An in situ method was developed to produce an Ni alloy composite coating reinforced by in situ reacted TiC particles with a gradient distribution, using one-step laser cladding with a pre-placed powder mixture on a 5CrMnMo steel substrate. Dispersed and ultra-fine TIC particles were formed in situ in the coating. Most. of the TiC particles, with a marked gradient distribution, were uniformly distributed within interdendritic regions because of the trapping effect of the advancing solid-liquid interface. In addition, the TiC-gamma-Ni interfaces generated in situ were found to be free from any deleterious surface reaction. Finally, the microhardness also showed a gradient variation, with the highest value of 1250 Hv0.2 and the wear properties of the coating were significantly enhanced.

Experimental Investigation On The Holdup Distribution Of Oil-Water Two-Phase Flow In Horizontal Parallel Tubes

An experimental investigation was conducted to study the holdup distribution of oil and water two-phase flow in two parallel tubes with unequal tube diameter. Tests were performed using white oil (of viscosity 52 mPa s and density 860 kg/m(3)) and tap water as liquid phases at room temperature and atmospheric outlet pressure. Measurements were taken of water flow rates from 0.5 to 12.5 m(3)/h and input oil volume fractions from 3 to 94 %. Results showed that there were different flow pattern maps between the run and bypass tubes when oil-water two-phase flow is found in the parallel tubes. At low input fluid flow rates, a large deviation could be found on the average oil holdup between the bypass and the run tubes. However, with increased input oil fraction at constant water flow rate, the holdup at the bypass tube became close to that at the run tube. Furthermore, experimental data showed that there was no significant variation in flow pattern and holdup between the run and main tubes. In order to calculate the holdup in the form of segregated flow, the drift flux model has been used here.

Reconstructing The Vertical Distribution Of The Aeolian Saltation Mass Flux Based On The Probability Distribution Of Lift-Off Velocity

The probability distribution of lift-off velocity of the saltating grains is a bridge to linking microscopic and macroscopic research of aeolian sand transport. The lift-off parameters of saltating grains (i.e., the horizontal and vertical lift-off velocities, resultant lift-off velocity, and lift-off angle) in a wind tunnel are measured by using a Phase Doppler Particle Analyzer (PDPA). The experimental results show that the probability distribution of horizontal lift-off velocity of saltating particles on a bed surface is a normal function, and that of vertical lift-off velocity is an exponential function. The probability distribution of resultant lift-off velocity of saltating grains can be expressed as a log-normal function, and that of lift-off angle complies with an exponential function. A numerical model for the vertical distribution of aeolian mass flux based on the probability distribution of lift-off velocity is established. The simulation gives a sand mass flux distribution which is consistent with the field data of Namikas (Namikas, S.L., 2003. Field measurement and numerical modelling of acolian mass flux distributions on a sandy beach, Sedimentology 50, 303-326). Therefore, these findings are helpful to further understand the probability characteristics of lift-off grains in aeolian sand transport. (c) 2007 Elsevier B.V. All rights reserved.

Thermal fatigue on pistons induced by shaped high power laser. Part II: Design of spatial intensity distribution via numerical simulation

In the laser induced thermal fatigue simulation test on pistons, the high power laser was transformed from the incident Gaussian beam into a concentric multi-circular pattern with specific intensity ratio. The spatial intensity distribution of the shaped beam, which determines the temperature field in the piston, must be designed before a diffractive optical element (DOE) can be manufactured. In this paper, a reverse method based on finite element model (FEM) was proposed to design the intensity distribution in order to simulate the thermal loadings on pistons. Temperature fields were obtained by solving a transient three-dimensional heat conduction equation with convective boundary conditions at the surfaces of the piston workpiece. The numerical model then was validated by approaching the computational results to the experimental data. During the process, some important parameters including laser absorptivity, convective heat transfer coefficient, thermal conductivity and Biot number were also validated. Then, optimization procedure was processed to find favorable spatial intensity distribution for the shaped beam, with the aid of the validated FEM. The analysis shows that the reverse method incorporated with numerical simulation can reduce design cycle and design expense efficiently. This method can serve as a kind of virtual experimental vehicle as well, which makes the thermal fatigue simulation test more controllable and predictable. (C) 2007 Elsevier Ltd. All rights reserved.

Interface Layer Effect On The Stress Distribution Of A Wafer-Bonded Bilayer Structure

The interface layer plays an important role in stress transfer in composite structures. However, many interface layer properties such as the modulus, thickness, and uniformity are difficult to determine. The model developed in this article links the influence of the interface layer on the normal stress distribution along the layer thickness with the layer surface morphology before bonding. By doing so, a new method of determining the interfacial parameter(s) is suggested. The effects of the layer thickness and the surface roughness before bonding on the normal stress distribution and its depth profile are also discussed. For ideal interface case with no interfacial shear stress, the normal stress distribution pattern can only be monotonically decreased from the interface. Due to the presence of interfacial shear stress, the normal stress distribution is much more complex, and varies dramatically with changes in the properties of the interface layer, or the dimensions of the bonding layers. The consequence of this dramatic stress field change, such as the shift of the maximum stress from the interface is also addressed. The size-dependent stress distribution in the thickness direction due to the interface layer effect is presented. When the interfacial shear stress is reduced to zero, the model presented in this article is also demonstrated to have the same normal stress distribution as obtained by the previous model, which does not consider the interface layer effect.