Numerical simulation of temperature field evolution of metallic alloy surface due to pulsed laser treatment

This paper performed a numerical simulation on temperature field evolution for the surface layer of a metallic alloy subjected to pulsed Nd:YAG laser treatment. The enthalpy method was adopted to solve the moving boundary problem, I.e. Stefan problem. Computational results were obtained to show the temperature field evolution. Effects of latent heat and mushy zone width on the temperature field were investigated. The results also show very high values of temperature gradient and cooling rate, which are typical characteristics during the solidification process.

Scaling Functions In Conical Indentation Of Elastic-Plastic Solids

The finite element method was used to simulate the conical indentation of elastic-plastic solids with work hardening. The ratio of the initial yield strength to the Young's modulus Y/E ranged from 0 to 0.02. Based on the calculation results, two sets of scaling functions for non-dimensional hardness H/K and indenter penetration h are presented in the paper, which have closed simple mathematical form and can be used easily for engineering application. Using the present scaling functions, indentation hardness and indentation loading curves can be easily obtained for a given set of material properties. Meanwhile one can use these scaling functions to obtain material parameters by an instrumented indentation load-displacement curve for loading and unloading if Young's modulus E and Poisson's ratio nu are known.

太阳风湍流和磁层亚暴的一种机制

太阳风的动量涨落将通过磁层边界在磁尾激发磁流体力学波。快磁声波携带扰动能量传到等离子体片中,发展为激波,或者通过激波的相互作用而耗散能量,使等离子体加热。等离子体片中的随机费米加速机制,使麦克斯韦分布尾巴部分的高能量粒子被加速到更高能。在宁静态时,加热、加速与耗散过程平衡。当太阳风的动量或者其涨落较大时,整个加热和加速过程加剧,更多的高能粒子产生,并从等离子体片中逃逸,形成高速的等离子体流注入近地轨道和极区,表现为磁层亚暴过程。利用这种机制,可以解释地球磁层亚暴的定性特征。

纳米压痕和划痕法测定氧化硅薄膜材料的力学特性

为了研究不同制备工艺对材料力学性能的影响 ,选择了热氧化、LPCVD和PECVD三种典型工艺 ,在硅片上制备 1μm氧化硅薄膜。通过纳米压痕和划痕检测可知 ,热氧化工艺制备的SiO2薄膜的硬度和模量最大 ,LPCVD制备的样品界面结合强度高于PECVD。纳米压痕和划痕技术为此提供了丰富的近表面弹塑性变形和断裂等的信息 ,是评价微米薄膜力学性能的有效手段

燃烧物理学基础

A block SPP algorithm for multidimensional tridiagonal equations with optimal message vector length

A parallel strategy for solving multidimensional tridiagonal equations is investigated in this paper. We present in detail an improved version of single parallel partition (SPP) algorithm in conjunction with message vectorization, which aggregates several communication messages into one to reduce the communication cost. We show the resulting block SPP can achieve good speedup for a wide range of message vector length (MVL), especially when the number of grid points in the divided direction is large. Instead of only using the largest possible MVL, we adopt numerical tests and modeling analysis to determine an optimal MVL so that significant improvement in speedup can be obtained.

Modified formula of Malus' law for Glan-Taylor polarizing prisms

A simple three-axis model has been developed, which has been successfully applied to the analysis of the light transmittance in spatial incident angle and the simulation of modified formula of Malus' law for Glan-Taylor prisms. Our results indicate that the fluctuations on the cosine squared curve are due to specific misalignments between the axis of the optical system, the optical axis of the prism and the mechanical axis (rotation axis) of prism, which results in the fact that different initial relative location of the to-be-measured-prism in the testing system corresponds to different shape of Malus' law curve. Methods to get absolutely smooth curve are proposed. This analysis is available for other kinds of Glan-type prisms. (C) 2004 Elsevier B.V. All rights reserved.

The origin of the transverse relaxation time in optically excited semiconductor quantum wells

The origin of the transverse relaxation time in optically excited semiconductor quantum wells is investigated based on the vector property of the interband transition matrix elements. The dephasing rate due to carrier-carrier (CC) scattering is found to be equal to half of the common momentum relaxation rate. The analytical expression of the polarization dephasing due to CC scattering in two-dimension is established and the dependence of the dephasing rate Gamma(cc) on the carrier density N is determined to be Gamma(cc) = constant (.) N-1/2, which is used to explain the experimental results and provides a promising physical picture. (C) 2004 Elsevier B.V. All rights reserved.

Transverse superresolution with the radial continuous transmittance filter

The radial continuous transmittance filter is presented to realize transverse superresolution. It consists of two parallel polarizers and a radial birefringent element sandwiched between of them. By adjusting the angle between optical axis of the radial birefringent element and the polarization direction of the polarizers, transverse superresolution can be realized. But transverse superresolution is obtained at the cost of the axial resolution and the increase of the side-lobes in strength. So we then mend such filter, with it not only enhance the transverse resolution but also suppress the influence of the side-lobes and the reduction of the axial resolution. At the same time, the Strehl ratio increases. The advantage of such a filter used in superresolution technique is that it is easy to fabricate because its fabrication does not deal with the variation of the phase. (c) 2005 Elsevier GmbH. All rights reserved.

"神光-Ⅱ"装置第九路靶场终端光学组件的研制

针对“神光-Ⅱ”装置第九路系统主激光瞄准精度小于等于30μm和大焦斑辐照均匀性优于10％的要求，提出了靶场终端光学组件的设计结构。应用有限元法对组件关键机械元件和ICF靶室整体进行动静态分析，优化了设计参数。同时与聚焦透镜配合进行数值分析列阵透镜，确定了单元数、曲率和厚度以及单元长和宽等参数。经过实验测试，主激光瞄准精度达到28．9μm，大焦斑辐照的形状为1000μm×500μm，均匀性为12．0％。

Synthesis, spectroscopic properties and thermal stability of metal(II) tetraazaporphyrin complexes with two strong wavelength absorption

Three kinds of metal(II) tetraazaporphyrin complexes with blue-violet and red light wavelength absorption were synthesized by refluxing tetraazaporphyrin ligand and different metal(II) ions, respectively. Their structures were confirmed by elemental analysis, LDI-TOF-MS, FT-IR and UV-Vis. The solubility of metal(II) tetraazaporphyrin complexes in organic solvents and absorption properties of their chloroform solution and films on K9 glass in the region 250-800 nm were measured. The influence on the difference of absorption maximum from metal(II) tetraazaporphyrin complexes to tetraazaporphyrin ligand by different metal(II) ions was studied. In addition, the thermal stability of the complexes was also evaluated. (c) 2006 Elsevier Ltd. All rights reserved.

Electrochemical fabrication and electronic behavior of polypyrrole nano-fiber array devices

Electrochemically active Polypyrrole (PPy) nano-fiber array device was fabricated via electrochemical deposition method using aluminum anodic oxide (AAO) membrane as template. After alkaline treatment electrochemically active PPy nano-fiber lost electrochemical activity, and became electrochemically inactive PPy. The electronic properties of PPy nano-fiber array devices were measured by means of a simple method. It was found that for an indium-tin oxide/electrochemically inactive PPy nano-fiber device, the conductivity of nano-fiber increased with the increase of voltage applied on the two terminals of nano-fiber. The electrochemical inactive PPy nano-fiber might be used as a nano-fiber switching diode. Both Au/electrochemically active PPy and Au/electrochemically inactive PPy nano-fiber devices demonstrate rectifying behavior, and might have been used for further application as nano-rectifiers. (c) 2005 Elsevier B.V. All tights reserved.

Effects of surface treatment on sapphire substrates

The influence of mechanical polishing, chemo-mechanical polishing (CMP), as well as CMP and subsequent chemical etching on the properties of sapphire substrate surfaces has been studied. The sapphire substrates have been investigated by means of polarizing microscopy, atomic force microscopy (AFM). X-ray diffraction rocking curves (XRCs) and micro-Raman spectroscopy. The results show that CMP with subsequent chemically etching yields the best-quality sapphire substrate surfaces. (C) 2004 Elsevier B.V. All rights reserved.

温梯法生长大尺寸蓝宝石晶体的脱碳去色退火研究

温度梯度法（temperature gradient technique，TGT）生长的Al2O3晶体因石墨发热体在高温时的挥发和原料中过渡性金属离子的存在，在不同部位呈现不同颜色，一般上部为浅红色，尾部为浅黄绿色．将TGT法生长的Al2O3晶体（Ф110×80mm^3）依次经过高温氧化气氛、高温还原气氛脱碳、去色退火实验，即“两步法”退火实验，晶体变成无色、透明．经测试，Al2O3晶体的完整性、光学透过率和光学均匀性均有显著提高.