Fatigue crack-growth rate in ferrite martensite dual-phase steel

An empirical study is made on the fatigue crack growth rate in ferrite-martensite dual-phase (FMDP) steel. Particular attention is given to the effect of ferrite content in the range of 24.2% to 41.5% where good fatigue resistance was found at 33.8%. Variations in ferrite content did not affect the crack growth rate when plotted against the effective stress intensity factor range  which was assumed to follow a linear relation with the crack tip stress intensity factor range ΔK. A high  corresponds to uniformly distributed small size ferrite and martensite. No other appreciable correlation could be ralated to the microstructure morphology of the FMDP steel. The closure stress intensity factor , however, is affected by the ferrite content with  reaching a maximum value of 0.7. In general, crack growth followed the interphase between the martensite and ferrite.

Dividing the fatigue crack growth process into Stage I and II where the former would be highly sensitive to changes in ΔK and the latter would increase with ΔK depending on the  ratio. The same data when correlated with the strain energy density factor range ΔS showed negligible dependence on mean stress or R ratio for Stage I crack growth. A parameter α involving the ratio of ultimate stress to yield stress, percent reduction of area and R is introduced for Stage II crack growth so that the  data for different R would collapse onto a single curve with a narrow scatter band when plotted against αΔS.

结构弛豫对Zr_(64.13)Cu_(15.75)Ni_(10.12)Al_(10)块体非晶合金硬度和剪切带特征的影响

通过接近玻璃转变温度的等温退火获得不同弛豫状态的Zr64.13Cu15.75Ni10.12Al10块体非晶合金样品。利用维氏显微硬度计和洛氏硬度计研究结构弛豫对合金硬度和压痕周围剪切带特征的影响规律。结果表明:在590K等温退火处理使Zr64.13Cu15.75Ni10.12Al10块体非晶合金发生焓弛豫行为,其维氏显微硬度随退火时间的延长较快增加后趋于稳定,而大载荷洛氏硬度对结构弛豫不敏感。通过洛氏压痕周围剪切带特征的研究,定量比较了结构弛豫对剪切带间距、数量的影响规律。

第13届美国复合材料学会技术年会简介

一．会议概况１．美国复合材料学会第１３届年会（Ｔｈｅ１３ｔｈＴｅｃｈｎｉｃａｌＣｏｎｆｅｒｅｎｃｅｏｆＡｍｅｒｉｃａｎＳｏｃｉｅｔｙｆｏｒＣｏｍｐｏｓｉｔｅ），于１９９８年９月２１～２３日在美国巴尔的摩（Ｂａｌｔｉｍｏｒｅ）举行，会议由马理兰大学（Ｍ...

激光熔覆大厚度Fe_(57)Co_8Ni_8Zr_(10)Si_4B_(13)非晶表层及其微结构研究

利用激光熔覆制备出1.2mm厚的Fe_(57)Co_8Ni_8Zr_(10)Si_4B_(13)大厚度非晶表层。用XRD,ES,TEM,DSC及硬度对获得的非晶表层进行了多种分析，研究了非晶合金表层的微结构与非晶形成能力。初步探讨了大厚度非晶表层的形式机制。

燃烧物理学基础

Freestanding optical fibers fabricated in a glass chip by femtosecond laser micromachining for lab-on-a-chip application (vol 13, pg 7225, 2005)

An erratum is presented to correct the propagation loss of the freestanding optical fibers fabricated in glass chip. (c) 2006 Optical Society of America.

Effect of hydroxyl groups on nonradiative decay of Er3+: I-4(13/2)-> I-4(15/2) transition in zinc tellurite glasses

A series of zinc tellurite glasses of 75TeO(2)-20ZnO-(5-x)La2O3-xEr(2)O(3) (x=0.02, 0.05, and 0.1 mol%) with the different hydroxl groups were prepared by the conventional melt-quenching method. Infrared spectra were measured in order to estimate the exact content of OH- groups in samples. The observed increase of the fluorescence lifetime with the oxygen bubbling time has been related to the reduction in the OH- content concentration as evidenced by IR transmission spectra. Various nonradiative decay rates from I-4(13/2) of Er3+ with. the change of OH content were determined from the fluorescence lifetime and radiative decay rates were calculated on the basis of Judd-Ofelt theory. (c) 2005 Elsevier B.V. All rights reserved.