Generating power from waves on a breakwater.

Outlines the possibility for wave power generation at artificial islands by construction of a breakwater. Reviews the development of wave energy systems, and describes several wave generators, e.g. the Mauritius lagoon system, the Nodding Duck, the oscillating cylinder, the oscillating water column and the Lancaster Bag. Applications and costs are outlined. (C.J.U.)

Sensorless commutation of a two-phase linear machine for marine renewable power generation

A sensorless scheme is presented for a two-phase permanent-magnet linear machine targeted for use in marine wave-power generation. This is a field where system reliability is a key concern. The scheme is able to extract the effective inductance and back-emf of the machine's phases simultaneously from measurements of the current ripple present on the power electronic converter. These measurements can then be used to estimate position. An enhancement to the scheme in the presence of spatially-varying mutual inductance between phases allows more accurate and reliable tracking from indutance-based measurements than would otherwise be expected. This scheme is able to operate at any speed including, critically, when stationary. Experimental results show promise for the scheme, although some work to reduce the level of noise would be desirable. © 2013 IEEE.

Beam propagation modelling of tapered waveguide lasers

A dynamic beam propagation model allows design optimization of high power low divergence tapered waveguide lasers. The model is extended to include spatially-resolved temperature profiles and a temperature dependent gain. Using this model, design parameters such as the optimum facet reflectivity, taper angle, and waveguide dimension can be calculated for low far-field divergence and high continuous wave power.

Use of a high-temperature superconducting coil for magnetic energy storage

A high temperature superconducting magnetic energy storage device (SMES) has been realised using a 350 m-long BSCCO tape wound as a pancake coil. The coil is mounted on a cryocooler allowing temperatures down to 17.2 K to be achieved. The temperature dependence of coil electrical resistance R(T) shows a superconducting transition at T 102.5 K. Measurements of the V(I) characteristics were performed at several temperatures between 17.2 K and 101.5 K to obtain the temperature dependence of the critical current (using a 1 νV/cm criterion). Critical currents were found to exceed 100 A for T < 30 K. An electronic DC-DC converter was built in order to control the energy flow in and out of the superconducting coil. The converter consists of a MOS transistor bridge switching at a 80 kHz frequency and controlled with standard Pulse Width Modulation (PWM) techniques. The system was tested using a 30 V squared wave power supply as bridge input voltage. The coil current, the bridge input and output voltages were recorded simultaneously. Using a 10 A setpoint current in the superconducting coil, the whole system (coil + DC-DC converter) can provide a stable output voltage showing uninterruptible power supply (UPS) capabilities over 1 s. © 2006 IOP Publishing Ltd.

Wave dispersion and power flow analysis of an infinite aerofoil-shaped beam

Classic flutter analysis models an aerofoil as a two degree-of-freedom rigid body supported by linear and torsional springs, which represent the bending and torsional stiffness of the aerofoil section. In this classic flutter model, no energy transfer or dissipation can occur in the span-wise direction of the aerofoil section. However, as the aspect ratio of an aerofoil section increases, this span-wise energy transfer - in the form of travelling waves - becomes important to the overall system dynamics. This paper extends the classic flutter model to include travelling waves in the span-wise direction. Namely, wave dispersion and power flow analysis of an infinite, aerofoil-shaped beam, subject to bending, torsion, tension and a constant wind excitation, is used to investigate the overall system stability. Examples of potential applications for these high aspect ratio aerofoil sections include high-altitude balloon tethers, towed cables, offshore risers and mooring lines.

ZnO film based surface acoustic wave micro-pump

In this study, a micro-pump unit based on surface acoustic wave (SAW) on piezoelectric ZnO film is designed and fabricated as a micro-fluidic device. It employs a mechanical wave, which is generated electrically using an aluminum interdigital transducer (IDT), and propagates on the surface of the ZnO film. The ZnO film was used in this study because it has a high electromechanical coefficient and an excellent bonding with various substrate materials, in particular silicon. The sputtering parameters for ZnO film deposition have been optimized, and the ZnO films with different thickness from 1 micron to 5.5 microns were prepared. The film properties have been characterized using different methods, such as scanning electron microscopy, X-ray diffraction and atomic force microscopy. Aluminum IDT with a finger width and spacing of 8 microns was patterned on the ZnO film using a lift-off process. The frequency generated was measured using a network analyzer, and it varies from 130 MHz to 180 MHz as a function of film thickness. A signal generator was used to generate the frequency with a power amplifier to amplify the signal, which was then applied to aluminum IDT to generate the surface acoustic wave. If a liquid droplet exists on the surface carrying the acoustic wave, the energy and the momentum of the SAW will be coupled into the fluid, causing the liquid to vibrate and move on film surface. The strength of this movement is determined by the applied voltage and frequency. The volume of the liquid drop loaded on the SAW device in this study is of several hundreds of nanoliters. The movement of the liquid inside the droplet and also on the ZnO film surface can be demonstrated. The performance of ZnO SAW device was characterized as a function of film thickness. © 2007 IOP Publishing Ltd.

DEVELOPMENT OF THE WAVE CONTOURING RAFT.

The wave contouring raft system is the outcome of ideas initiated and developed by Sir Christopher Cockerell from 1972 onwards. His objective was to develop a wave energy device which is within the bounds of current technology. It should consist of simple, relatively small units, amenable to quantity production, which would enable a power generating system to be built up and commissioned in stages according to needs and production capability. This thinking led to the investigation of chains of pontoons, hinged together so that the passage of a wave down the chain causes the pontoons to oscillate relative to one another. Energy is extracted from the sea by applying a torque about the hinges to damp the motion. The work has involved extensive model testing in wave tanks and the building and testing of a 3-unit 1/10 scale power generating installation in the Solent, as well as design studies for a full size installation for Atlantic conditions.

Plume attenuation under high power Nd:yttritium-aluminum-garnet laser welding

During high-power continuous wave (cw) Nd:yttritium-aluminum-garnet (YAG) laser welding a vapor plume is formed containing vaporized material ejected from the keyhole. The gas used as a plume control mechanism affects the plume shape but not its temperature, which has been found to be less than 3000 K, independent of the atmosphere and plume control gases. In this study high-power (up to 8 kW) cw Nd:YAG laser welding has been performed under He, Ar, and N2 gas atmospheres, extending the power range previously studied. The plume was found to contain very small evaporated particles of diameter less than 50 nm. Rayleigh and Mie scattering theories were used to calculate the attenuation coefficient of the incident laser power by these small particles. In addition the attenuation of a 9 W Nd:YAG probe laser beam, horizontally incident across the plume generated by the high-power Nd:YAG laser, was measured at various positions with respect to the beam-material interaction point. Up to 40% attenuation of the probe laser power was measured at positions corresponding to zones of high concentration of vapor plume, shown by high-speed video measurements. These zones interact with the high-power Nd:YAG laser beam path and, can result in significant laser power attenuation. © 2004 Laser Institute of America.

A comparison of power losses for small (< 1 kW) induction motor drives adopting squarewave and sinusoidal PWM excitation

In this paper the influence of the form of motor excitation on the performance of a small (< 1 kW) induction motor drive is studied. Two forms of excitation, namely sine waves generated by pulse width modulation and simple square wave are explored. Sine wave excitation gives lower motor losses but increases inverter losses. Conversely, square wave excitation increases motor losses but decreases inverter losses. Losses have been measured directly by calorimetric means or, in the case of the inverter, predicted by a Pspice model that has been verified by calorimetric methods. The work shows that overall, the use of square wave excitation leads to a more efficient drive. © 2004 The Institution of Electrical Engineers.

Wave energy emulator and AC/DC rectifiers for direct drive wave energy converters

This paper describes a solid state electrical emulator devised for laboratory testing of power conditioning electronics for direct drive linear wave energy converters (DDLWEC). Two rectification strategies are considered; a uni-directional boost topology, and an H-bridge which may be controlled in either uni- or bidirectional modes.

Design and commissioning of a 30kw direct drive wave generator

The Trident Energy TE5 is a prototype wave energy converter operating on the principle of having direct-drive linear generators mounted above the water surface, coupled to floats moving under the rig deck. This paper describes aspects of the TE5 design, including its generators, power electronic systems and the conception of its marine structure.

Modelling non-linearities in a MEMS square wave oscillator

The modelling of the non-linear behaviour of MEMS oscillators is of interest to understand the effects of non-linearities on start-up, limit cycle behaviour and performance metrics such as output frequency and phase noise. This paper proposes an approach to integrate the non-linear modelling of the resonator, transducer and sustaining amplifier in a single numerical modelling environment so that their combined effects may be investigated simultaneously. The paper validates the proposed electrical model of the resonator through open-loop frequency response measurements on an electrically addressed flexural silicon MEMS resonator driven to large motional amplitudes. A square wave oscillator is constructed by embedding the same resonator as the primary frequency determining element. Measurements of output power and output frequency of the square wave oscillator as a function of resonator bias and driving voltage are consistent with model predictions ensuring that the model captures the essential non-linear behaviour of the resonator and the sustaining amplifier in a single mathematical equation. © 2012 IEEE.