Characterisation of ultrafast micro-structuring of alumina (Al 2O3)

Alumina ceramic, Al2O3, presents a challenge to laser micro-structuring due to its neglible linear absorption coefficient in the optical region coupled with its physical properties such as extremely high melting point and high thermal conductivity. In this work, we demonstrate clean micro-structuring of alumina using NIR (λ=775 nm) ultrafast optical pulses with 180 fs duration at 1kHz repetition rate. Sub-picosecond pulses can minimise thermal effects along with collateral damage when processing conditions are optimised, consequently, observed edge quality is excellent in this regime. We present results of changing micro-structure and morphology during ultrafast processing along with measured ablation rates and characteristics of developing surface relief. Initial crystalline phase (alpha Al2O3) is unaltered by femtosecond processing. Multi-pulse ablation threshold fluence Fth, ∼ 1.1 Jcm-2 and at low fluence ∼ 3 Jcm -2, independent of machined depth, there appears to remain a ∼ 2 μm thick rapidly re-melted layer. On the other hand, micro-structuring at high fluence F ∼ 21 Jcm-2 shows no evidence of melting and the machined surface is covered with a fine layer of debris, loosely attached. The nature of debris produced by femtosecond ablation has been investigated and consists mainly of alumina nanoparticles with diameters from 20 nm to 1 micron with average diameter ∼ 300 nm. Electron diffraction shows these particles to be essentially single crystal in nature. By developing a holographic technique, we have demonstrated periodic micrometer level structuring on polished samples of this extremely hard material.

Numerical modelling of lubricated foil rolling

A model of lubricated cold strip rolling (1, 2) is extended to the thin foil regime. The model considers the evolution of asperity geometry and lubricant pressure through the bite, treating the strip using a conventional slab model. The elastic deflections of the rolls are coupled into the problem using an elastic finite element model. Friction between the roll and the asperities on the strip is modelled using the Coulomb and Tresca friction factor approaches. The shear stress in the Coulomb friction model is limited to the shear yield stress of the strip. A novel modification to these standard friction laws is used to mimic slipping friction in the reduction regions and sticking friction in a central neutral zone. The model is able to reproduce the sticking and slipping zones predicted by Fleck et al. (3). The variation of rolling load, lubricant film thickness and asperity contact area with rolling speed is examined, for conditions typical of rolling aluminium foil from a thickness of 50 to 25 μm. T he contact area and hence friction rises as the speed drops, leading to a large increase in rolling load. This increase is considerably more marked using Coulomb friction as compared with the friction factor approach. Forward slip increases markedly as the speed falls and a significant sticking region develops.

RNAi, DRD1, and histone methylation actively target developmentally important Non-CG DNA methylation in Arabidopsis

Cytosine DNA methylation protects eukaryotic genomes by silencing transposons and harmful DNAs, but also regulates gene expression during normal development. Loss of CG methylation in the Arabidopsis thaliana met1 and ddm1 mutants causes varied and stochastic developmental defects that are often inherited independently of the original met1 or ddm1 mutation. Loss of non-CG methylation in plants with combined mutations in the DRM and CMT3 genes also causes a suite of developmental defects. We show here that the pleiotropic developmental defects of drm1 drm2 cmt3 triple mutant plants are fully recessive, and unlike phenotypes caused by met1 and ddm1, are not inherited independently of the drm and cmt3 mutations. Developmental phenotypes are also reversed when drm1 drm2 cmt3 plants are transformed with DRM2 or CMT3, implying that non-CG DNA methylation is efficiently re-established by sequence-specific signals. We provide evidence that these signals include RNA silencing though the 24-nucleotide short interfering RNA (siRNA) pathway as well as histone H3K9 methylation, both of which converge on the putative chromatin-remodeling protein DRD1. These signals act in at least three partially intersecting pathways that control the locus-specific patterning of non-CG methylation by the DRM2 and CMT3 methyltransferases. Our results suggest that non-CG DNA methylation that is inherited via a network of persistent targeting signals has been co-opted to regulate developmentally important genes. © 2006 Chan et al.

How to avoid the problems of target-setting

Purpose: Advocates and critics of target-setting in the workplace seem unable to reach beyond their own well-entrenched battle lines. While the advocates of goal-directed behaviour point to what they see as demonstrable advantages, the critics of target-setting highlight equally demonstrable disadvantages. Indeed, the academic literature on this topic is currently mired in controversy, with neither side seemingly capable of envisaging a better way forward. This paper seeks to break the current deadlock and move thinking forward in this important aspect of performance measurement and management by outlining a new, more fruitful approach, based on both theory and practical experience. Design/methodology/approach: The topic was approached in three phases: assembling and reading key academic and other literature on the subject of target-setting and goal-directed behaviour, with a view to understanding, in depth, the arguments advanced by the advocates and critics of target-setting; comparing these published arguments with one's own experiential findings, in order to bring the essence of disagreement into much sharper focus; and then bringing to bear the academic and practical experience to identify the essential elements of a new, more fruitful approach offering all the benefits of goal-directed behaviour with none of the typical disadvantages of target-setting. Findings: The research led to three key findings: the advocates of goal-directed behaviour and critics of target-setting each make valid points, as seen from their own current perspectives; the likelihood of these two communities, left to themselves, ever reaching a new synthesis, seems vanishingly small (with leading thinkers in the goal-directed behaviour community already acknowledging this); and, between the three authors, it was discovered that their unusual combination of academic study and practical experience enabled them to see things differently. Hence, they would like to share their new thinking more widely. Research limitations/implications: The authors fully accept that their paper is informed by extensive practical experience and, as yet, there have been no opportunities to test their findings, conclusions and recommendations through rigorous academic research. However, they hope that the paper will move thinking forward in this arena, thereby informing future academic research. Practical implications: The authors hope that the practical implications of the paper will be significant, as it outlines a novel way for organisations to capture the benefits of goal-directed behaviour with none of the disadvantages typically associated with target-setting. Social implications: Given that increased efficiency and effectiveness in the management of organisations would be good for society, the authors think the paper has interesting social implications. Originality/value: Leading thinkers in the field of goal-directed behaviour, such as Locke and Latham, and leading critics of target-setting, such as Ordóñez et al. continue to argue with one another - much like, at the turn of the nineteenth century, proponents of the "wave theory of light" and proponents of the "particle theory of light" were similarly at loggerheads. Just as this furious scientific debate was ultimately resolved by Taylor's experiment, showing that light could behave both as a particle and wave at the same time, the authors believe that the paper demonstrates that goal-directed behaviour and target-setting can successfully co-exist. © Emerald Group Publishing Limited.

Developing a technology intelligence strategy at kodak european research: Scan & target

OVERVIEW: Kodak European Research (KER) developed a strategy for technology intelligence based on a theoretical model developed by Kerr et al. (2006). KER scouts designed and implemented a four-step approach to identify relevant technologies and research centers across Europe, Africa and the Middle East. The approach provides clear guidance for integrating web searches, scouting trips, networking and interactions with intermediaries. KER's example illustrates how companies can organize themselves to look outside corporate boundaries in search of technologies relevant for their business. The approach may be useful to those in other companies who have been asked to start a technology intelligence activity. © 2010 Industrial Research Institute, Inc.

Control of material transport through pulse shape manipulation-a development toward designer pulses

The variety of laser systems available to industrial laser users is growing and the choice of the correct laser for a material target application is often based on an empirical assessment. Industrial master oscillator power amplifier systems with tuneable temporal pulse shapes have now entered the market, providing enormous pulse parameter flexibility in an already crowded parameter space. In this paper, an approach is developed to design interaction parameters based on observations of material responses. Energy and material transport mechanisms are studied using pulsed digital holography, post process analysis techniques and finite-difference modelling to understand the key response mechanisms for a variety of temporal pulse envelopes incident on a silicon (1/1/1) substrate. The temporal envelope is shown to be the primary control parameter of the source term that determines the subsequent material response and the resulting surface morphology. A double peak energy-bridged temporal pulse shape designed through direct application of holographic imaging data is shown to substantially improve surface quality. © 2014 IEEE.

Colliding-pulse modelocked quantum dot lasers

Colliding pulse modelocking is demonstrated for the first time in quantum dot lasers. Using 3.9 mm-long devices with a 245 pm-long central absorber, 7 ps pulses at a repetition rate of 20 GHz is obtained. For Gaussian pulses a time-bandwidth product close to the Fourier transform limit is determined. These results confirm the potential of quantum dot lasers for high repetition rate harmonic modelocking.

Formation of nanoparticles from ultrafast laser condensates of metal targets

Optimised ultrafast laser ablation can result in almost complete ionisation of the target material and the formation of a high velocity plasma jet. Collisions with the ambient gas behind the shock front cools the material resulting in the formation of mainly spherical, single crystal nanoscale particles in the condensate. This work characterises the nanoscale structures produced by the ultrafast laser interactions in He atmospheres at STP with Ni and Al. High resolution transmission electron microscopy was employed to study the microstructure of the condensates and to classify the production of particles forms as a function of the illumination conditions.

Ultra-high density carbon nanotubes on Al-Cu for advanced vias

An integration scheme for carbon nanotube via interconnects is described to produce nanotube densities of 2.5 1012 tubes/cm2 or 8 1012 walls/cm2 on metallic Al-Cu lines, an order of magnitude beyond the previous state of art, and, for first time, close to that needed for implementation. ©2010 Crown.

High peak power femtosecond pulse VECSELs for terahertz time domain spectroscopy

We report on a high peak power femtosecond modelocked VECSEL and its application as a drive laser for an all semiconductor terahertz time domain spectrometer. The VECSEL produced near-transform-limited 335 fs sech2 pulses at a fundamental repetition rate of 1 GHz, a centre wavelength of 999 nm and an average output power of 120 mW. We report on the effect that this high peak power and short pulse duration has on our generated THz signal.