Microfabrication and application of reservoir pins for liquid transfer in biotechnology

Microarraying involves laying down genetic elements onto a solid substrate for DNA analysis on a massively parallel scale. Microarrays are prepared using a pin-based robotic platform to transfer liquid samples from microtitre plates to an array pattern of dots of different liquids on the surface of glass slides where they dry to form spots diameter < 200 μm. This paper presents the design, materials selection, micromachining technology and performance of reservoir pins for microarraying. A conical pin is produced by (i) conventional machining of stainless steel or wet etching of tungsten wire, followed by (ii) micromachining with a focused laser to produce a microreservoir and a capillary channel structure leading from the tip. The pin has a flat end diameter < 100 μm from which a 500 μm long capillary channel < 15 μm wide leads up the pin to a reservoir. Scanning electron micrographs of the metal surface show roughness on the scale of 10 μm, but the pins nevertheless give consistent and reproducible spotting performance. The pin capacity is 80 nanolitres of fluid containing DNA, and at least 50 spots can be printed before replenishing the reservoir. A typical robot holds can hold up to 64 pins. This paper discusses the fabrication technology, the performance and spotting uniformity for reservoir pins, the possible limits to miniaturization of pins using this approach, and the future prospects for contact and non-contact arraying technology.

Superconducting magnetic bearings for energy storage flywheels

We are investigating the use of flywheels for energy storage. Flywheel devices need to be of high efficiency and an important source of losses is the bearings. In addition, the requirement is for the devices to have long lifetimes with minimal or no maintenance. Conventional rolling element bearings can and have been used, but a non-contact bearing, such as a superconducting magnetic bearing, is expected to have a longer lifetime and lower losses. At Cambridge we have constructed a flywheel system. Designed to run in vacuum this incorporates a 40kg flywheel supported on superconducting magnetic bearings. The production device will be a 5kW device storing 5 kWh of retrievable energy at 50,000 rpm. The Cambridge system is being developed in parallel with a similar device supported on a conventional bearing. This will allow direct performance comparisons. Although superconducting bearings are increasingly well understood, of major importance are the cryogenics and special attention is being paid to methods of packaging and insulating the superconductors to cut down radiation losses. The work reported here is part of a three-year program of work supported by the EPSRC. © 1999 IEEE.

Vibration of a high-altitude tethered balloon with application to climate engineering

A balloon tethered at an altitude of 20 km could deliver a particulate cloud leading to global cooling. Tethering a balloon at this altitude poses significant problems with respect to vibration and stability, especially in regions of high wind. No-one has ever proposed, yet alone launched, a balloon at an altitude of 20 km tethered to the ground. Owing to wind, the tether needs to be 23 km in length and is to be fixed to a ship at sea or on land in equatorial regions. Whilst the balloon at 20 km is subject to relatively modest wind conditions, at jet stream altitudes (10km) the tether will experience much higher wind loadings, not only because of the high wind speeds of up to 300 km / hr but also because of the high air density. A tether of circular cross section in these high winds will be subject to horizontal and downward drag forces that would bring the aerostat down. For this reason it is advantageous to consider a self-aligning tether of an aerodynamic cross section whereby it is possible to reduce the drag substantially. One disadvantage of a non-circular tether is the possibility of flutter and galloping instabilities. It is reasonably straightforward to model these phenomena for short lengths of aerofoil, but the situation becomes more complex for a 20 km tensioned tether with large deflection and curvature, variable wind speed, variable air density and variable tension. Analysis using models of infinite length are used to establish the stability at a local scale where the tension, aerodynamic and geometric properties are considered constant. Dispersion curve analysis is useful here. But for dynamics on a long-wavelength scale (several km) then a full non-linear analysis is required. This non-linear model can be used to establish the local values of tension appropriate for the dispersion analysis. This keynote presentation will give some insight into these issues.

Measuring the electrical properties of semiconductor nanowires using terahertz conductivity spectroscopy

Accurately measuring the electronic properties of nanowires is a crucial step in the development of novel semiconductor nanowire-based devices. With this in mind, optical pump-terahertz probe (OPTP) spectroscopy is ideally suited to studies of nanowires: it provides non-contact measurement of carrier transport and dynamics at room temperature. OPTP spectroscopy has been used to assess key electrical properties, including carrier lifetime and carrier mobility, of GaAs, InAs and InP nanowires. The measurements revealed that InAs nanowires exhibited the highest mobilities and InP nanowires exhibited the lowest surface recombination velocity. © 2013 Copyright SPIE.

Non-ohmic contact resistance and field-effect mobility in nanocrystalline silicon thin film transistors

Contact resistance has a significant impact on the electrical characteristics of thin film transistors. It limits their maximum on-current and affects their subsequent behavior with bias. This distorts the extracted device parameters, in particular, the field-effect mobility. This letter presents a method capable of accounting for both the non-ohmic (nonlinear) and ohmic (linear) contact resistance effects solely based upon terminal I-V measurements. Applying our analysis to a nanocrystalline silicon thin film transistor, we demonstrate that contact resistance effects can lead to a twofold underestimation of the field-effect mobility. © 2008 American Institute of Physics.