Superconducting fault current limiter design using parallel-connected YBCO thin films

Superconducting Fault Current Limiters (SFCLs) are able to reduce fault currents to an acceptable value, reducing potential mechanical and thermal damage to power system apparatus and allowing more flexibility in power system design and operation. The device can also help avoid replacing circuit breakers whose capacity has been exceeded. Due to limitations in current YBCO thin film manufacturing processes, it is not easy to obtain one large thin film that satisfies the specifications for high voltage and large current applications. The combination of standardized thin films has merit to reduce costs and maintain device quality, and it is necessary to connect these thin films in different series and parallel configurations in order to meet these specifications. In this paper, the design of a resistive type SFCL using parallel-connected YBCO thin films is discussed, including the role of a parallel resistor and the influence of individual thin film characteristics, based on both theory and experimental results. © 2009 IEEE.

Design support for turbomachinery

From the steam turbines which provide most of our electricity to the jet engines which have shrunk our World, turbomachines undoubtedly play a major role in life today. Competition in the turbomachinery industry is fiercely strong [Wisler, 1998], hence good aerodynamic design is vital. However, with efficiency levels already close to their theoretical maxima, companies are increasingly looking to reduce costs and increase reliability through improved design practice. Computational Fluid Dynamics (CFD) can make a strong contribution to assisting this process as it has the potential to increase performance while reducing cost. The situation is, however, complicated by an ever decreasing number of engineers with sufficient design experience to reap the full benefits offered by CFD. With the large risks involved, novice designers of today are increasingly confined to refining old designs rather than gaining experience, like their forebears, through 'clean sheet' exercises. Hence it is desirable to capture the knowledge and experience of older designers, before it is lost, to assist the engineers of tomorrow. It is therefore the aim of this project to produce a design support tool which will not only store the appropriate CFD codes, but also provide a dynamic signpost (based on elicited knowledge and experience) to advise the engineer in their use. The signposting methodology developed for the aerospace industry [Clarkson and Hamilton, 1997] will provide the basic framework for the tool. This paper reviews current turbomachinery design practice (including an examination of the relevant CFD) in order to establish the important issues which a support tool must address. Current design support methodologies and their propriety are then reviewed, followed by a detailed description of the signposting concept. It then sets out a clear statement of the objectives for the research and the methods proposed to meet them. The paper concludes with a timetable of the work.

Centrifuge modelling of pile-soil interaction in liquefiable slopes

Piles passing through sloping liquefiable deposits are prone to lateral loading if these deposits liquefy and flow during earthquakes. These lateral loads caused by the relative soil-pile movement will induce bending in the piles and may result in failure of the piles or excessive pile-head displacement. Whilst the weak nature of the flowing liquefied soil would suggest that only small loads would be exerted on the piles, it is known from case histories that piles do fail owing to the influence of laterally spreading soils. It will be shown, based on dynamic centrifuge test data, that dilatant behaviour of soil close to the pile is the major cause of these considerable transient lateral loads which are transferred to the pile. This paper reports the results of geotechnical centrifuge tests in which models of gently sloping liquefiable sand with pile foundations passing through them were subjected to earthquake excitation. The soil close to the pile was instrumented with pore-pressure transducers and contact stress cells in order to monitor the interaction between soil and pile and to track the soil stress state both upslope and downslope of the pile. The presence of instrumentation measuring pore-pressure and lateral stress close to the pile in the research described in this paper gives the opportunity to better study the soil stress state close to the pile and to compare the loads measured as being applied to the piles by the laterally spreading soils with those suggested by the JRA design code. This test data shows that lateral stresses much greater than one might expect from calculations based on the residual strength of liquefied soil may be applied to piles in flowing liquefied slopes owing to the dilative behaviour of the liquefied soil. It is shown at least for the particular geometry studied that the current JRA design code can be un-conservative by a factor of three for these dilation-affected transient lateral loads.

Designing intrinsically motivating user interfaces for the ageing population

Older people often find it difficult to learn to use new technology. Although they may want to adopt it, they can find the learning process challenging and frustrating and subsequently lose motivation. This paper looks at how psychological theories of intrinsic motivation could be applied to make the ICT learning process more engaging for older users and describes an experiment set up to test the applicability of these theories to user interface (UI) design. The results of the experiment confirmed that intrinsic motivation theory is a valid lens through which to look at current ICT design and also uncovered significant gender differences in reaction to different kinds of learning tasks. © 2013 Springer-Verlag Berlin Heidelberg.

The limits of inclusive design in the current design practice

The adoption of inclusive design principles and methods in the design practice is meant to support the equity of use of everyday products by as many people as possible independently of their age, physical, sensorial and cognitive capabilities. Although the intention is highly valuable, inclusive design approaches have not been widely applied in industrial context. This paper analyses the findings of an empirical research conducted with industrial designers and product managers. The research indicates some of the hindrances to the adoption of inclusive design, such as the current way the market is considered and targeted, and; the way the designers are driven by the project's brief and budget to orient their research strategy and activities. The paper proposes a way to improve the current industrial mode by strategically supplying clients, designers or both together with information about inclusivity. © 2013 Taylor & Francis Group.