An experimental study on the load carrying capacity of cold-formed steel studs and panels

A full-scale experimental study on the structural performance of load-bearing wall panels made of cold-formed steel frames and boards is presented. Six different types of C-channel stud, a total of 20 panels with one middle stud and 10 panels with two middle studs were tested under vertical compression until failure. For panels, the main variables considered are screw spacing (300 mm, 400 mm, or 600 mm) in the middle stud, board type (oriented strand board - OSB, cement particle board - CPB, or calcium silicate board - CSB), board number (no sheathing, one-side sheathing, or two-side sheathing), and loading type (1, 3, or 4-point loading). The measured load capacity of studs and panels agrees well with analytical prediction. Due to the restraint by rivet connections between stud and track, the effective length factor for the middle stud and the side stud in a frame (unsheathed panel) is reduced to 0.90 and 0.84, respectively. The load carrying capacity of a stud increases significantly whenever one- or two-side sheathing is used, although the latter is significantly more effective. It is also dependent upon the type of board used. Whereas panels with either OSB or CPB boards have nearly identical load carrying capacity, panels with CSB boards are considerably weaker. Screw spacing affects the load carrying capacity of a stud. When the screw spacing on the middle stud in panels with one-side sheathing is reduced from 600 mm to 300 mm, its load carrying capacity increases by 14.5 %, 20.6% and 94.2% for OSB, CPB and CSB, respectively.

Plasma enhanced chemical vapour deposited carbon nanotubes for field emission applications

Plasma Enhanced Chemical Vapour Deposition is an extremely versatile technique for directly growing multiwalled carbon nanotubes onto various substrates. We will demonstrate the deposition of vertically aligned nanotube arrays, sparsely or densely populated nanotube forests, and precisely patterned arrays of nanotubes. The high-aspect ratio nanotubes (∼50 nm in diameter and 5 microns long) produced are metallic in nature and direct contact electrical measurements reveal that each nanotube has a current carrying capacity of 107-108 A/cm2, making them excellent candidates as field emission sources. We examined the field emission characteristics of dense nanotube forests as well as sparse nanotube forests and found that the sparse forests had significantly lower turn-on fields and higher emission currents. This is due to a reduction in the field enhancement of the nanotubes due to electric field shielding from adjacent nanotubes in the dense nanotube arrays. We thus fabricated a uniform array of single nanotubes to attempt to overcome these issues and will present the field emission characteristics of this.

Critical current anisotropy in high temperature superconductors

After nearly 15 years of research effort, High Temperature Superconductors (HTS) are finding a wide range of practical applications. A clear understanding of the factors controlling the current carrying capacity of these materials is a prerequisite to their successful technological development. The critical current density (Jc) in HTS is directly dependent on the structure and pinning of the Flux Line Lattice (FLL) in these materials. This thesis presents an investigation of the Jc anisotropy in HTS. The use of thin films grown on off c-axis (vicinal) substrates allowed the effect of current directions outside the cuprate planes to be studied. With this experimental geometry Berghuis, et al. (Phys. Rev. Lett. 79, 12, pg. 2332) observed a striking flux channelling effect in vicinal YBa2Cu3O7-δ (YBCO) films. By confirming, and extending, this observation, it is demonstrated that this is an intrinsic effect. The results obtained, appear to fit well with the predictions of a field angle dependent cross-over from a three dimensional rectilinear FLL to a kinked lattice of strings and pancakes. The pinning force density for movement of strings inside the cuprate planes is considerably less than that on vortex pancake elements. When the FLL is entirely string-like this reduced pinning leads to the observed channelling minima. It is observed that anti-phase boundaries enhance the Jc in vicinal YBCO films by strongly pinning vortex strings. The effect on the FLL structure cross-over of increasing anisotropy has been elucidated using de-oxygenated vicinal YBCO films. Intriguingly, the counter intuitive prediction that the range of applied field angle for which the kinked lattice is fully developed reduces with increasing anisotropy, appears to be confirmed. Although vortex channelling cannot be observed in c-axis YBCO films, the pinning force density for vortex string channelling has been extracted by observing string dragging. By studying the effect of rotating the applied field at a constant angle to the cuprate planes, it is possible to observe the cross-over into the string pancake regime in c-axis films. In the 3D region, the observed behaviour is well explained by the anisotropic Ginzburg-Landau model. Measurements were also made on thin films of the much more anisotropic Bi 2Sr2CaCu2O8+x material, grown on vicinal substrates. The absence of any flux channelling effect and clear adherence to the expected Kes-Law behaviour in the observed Jc characteristics does not provide evidence for the existence of the predicted ‘crossing lattice’ in Bi 2Sr2CaCu2O8+x .

Compact holographic optical interconnections using nematic liquid crystal spatial light modulators

In a fibre-optic communication network, the wavelength-division multiplexing (WDM) technique enables an expansion of the data-carrying capacity of optical fibres. This can be achieved by transmitting different channels on a single optical fibre, with each channel modulating a different wavelength. In order to access and manipulate these channels at a node of the network, a compact holographic optical switch is designed, modelled, and constructed. The structure of such a switch consists of a series of optical components which are used to collimate the beam from the input, de-multiplex each individual wavelength into separated channels, manipulate the separated channels, and reshape the beam to the output. A spatial light modulator (SLM) is crucial in this system, offering control and flexibility at the channel manipulation stage, and providing the ability to redirect light into the desired output fibre. This is achieved by the use of a 2-D analogue phase computer generated hologram (CGH) based on liquid crystal on silicon (LCOS) technology. © 2011 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

Closely correlating lower and upper bound plastic analysis of real slabs

An engineer assessing the load-carrying capacity of an existing reinforced concrete slab is likely to use elastic analysis to check the load at which the structure might be expected to fail in flexure or in shear. In practice, many reinforced concrete slabs are highly ductile in flexure, so an elastic analysis greatly underestimates the loads at which they fail in this mode. The use of conservative elastic analysis has led engineers to incorrectly condemn many slabs and therefore to specify unnecessary and wasteful flexural strengthening or replacement. The lower bound theorem is based on the same principles as the upper bound theorem used in yield line analysis, but any solution that rigorously satisfies the lower bound theorem is guaranteed to be a safe underestimate of the collapse load. Jackson presented a rigorous lower bound method that obtains very accurate results for complex real slabs.

The soft impact response of composite laminate beams

The quasi-static and dynamic responses of laminated beams of equal areal mass, made from monolithic CFRP and Ultra high molecular weight Polyethylene (UHMWPE), have been measured. The end-clamped beams were impacted at mid-span by metal foam projectiles to simulate localised blast loading. The effect of clamping geometry on the response was investigated by comparing the response of beams bolted into the supports with the response of beams whose ends were wrapped around the supports. The effect of laminate shear strength upon the static and dynamic responses was investigated by testing two grades of each of the CFRP and UHMWPE beams: (i) CFRP beams with a cured matrix and uncured matrix, and (ii) UHMWPE laminates with matrices of two different shear strengths. Quasi-static stretch-bend tests indicated that the load carrying capacity of the UHWMPE beams exceeds that of the CFRP beams, increases with diminishing shear strength of matrix, and increases when the ends are wrapped rather than through-bolted. The dynamic deformation mode of the beams is qualitatively different from that observed in the quasi-static stretch-bend tests. In the dynamic case, travelling hinges emanate from the impact location and propagate towards the supports; the beams finally fail by tensile fibre fracture at the supports. The UHMWPE beams outperform the CFRP beams in terms of a lower mid-span deflection for a given impulse, and a higher failure impulse. Also, the maximum attainable impulse increases with decreasing shear strength for both the UHMWPE and CFRP beams. The ranking of the beams for load carrying capacity in the quasi-static stretch-bend tests is identical to that for failure impulse in the impact tests. Thus, the static tests can be used to gauge the relative dynamic performances of the beams. © 2013 Elsevier Ltd. All rights reserved.

High performance fibre-reinforced cementitious composite (CARDIFRC) - Performance and application to retrofitting

This paper describes first some of the recent performance checks on the high performance fibre-reinforced cementitious composite CARDIFRC and then its application to the retrofitting of damaged concrete beams. It is shown that an even distribution of fibres throughout the bulk of the material is crucial to its excellent fatigue performance and to the reduction in the autogenous shrinkage strains. The distribution of fibres in beams, cylinders and strips is examined using computerised tomography imaging and traditional image analysis. Thin strips of CARDIFRC are used to retrofit damaged concrete beams which are subjected to thermal cycling. It is shown that neither the load carrying capacity of the retrofitted beams nor the bond between retrofit strips and concrete deteriorates with thermal cycling. The load carrying capacity of retrofitted beams is predicted with a model based on fracture mechanics, and the predictions are shown to be in good agreement with test data. © 2006 Elsevier Ltd. All rights reserved.

Prices need no preferences: social trends determine decisions in experimental markets for pain relief.

OBJECTIVE: A standard view in health economics is that, although there is no market that determines the "prices" for health states, people can nonetheless associate health states with monetary values (or other scales, such as quality adjusted life year [QALYs] and disability adjusted life year [DALYs]). Such valuations can be used to shape health policy, and a major research challenge is to elicit such values from people; creating experimental "markets" for health states is a theoretically attractive way to address this. We explore the possibility that this framework may be fundamentally flawed-because there may not be any stable values to be revealed. Instead, perhaps people construct ad hoc values, influenced by contextual factors, such as the observed decisions of others. METHOD: The participants bid to buy relief from equally painful electrical shocks to the leg and arm in an experimental health market based on an interactive second-price auction. Thirty subjects were randomly assigned to two experimental conditions where the bids by "others" were manipulated to follow increasing or decreasing price trends for one, but not the other, pain. After the auction, a preference test asked the participants to choose which pain they prefer to experience for a longer duration. RESULTS: Players remained indifferent between the two pain-types throughout the auction. However, their bids were differentially attracted toward what others bid for each pain, with overbidding during decreasing prices and underbidding during increasing prices. CONCLUSION: Health preferences are dissociated from market prices, which are strongly referenced to others' choices. This suggests that the price of health care in a free-market has the capacity to become critically detached from people's underlying preferences.