Effects of longer heavy vehicles on traffic congestion

Two-lane, "microscopic" (vehicle-by-vehicle) simulations of motorway traffic are developed using existing models and validated using measured data from the M25 motorway. An energy consumption model is also built in, which takes the logged trajectories of simulated vehicles as drive-cycles. The simulations are used to investigate the effects on motorway congestion and fuel consumption if "longer and/or heavier vehicles" (LHVs) were to be permitted in the UK. Baseline scenarios are simulated with traffic composed of cars, light goods vehicles and standard heavy goods vehicles (HGVs). A proportion of conventional articulated HGVs is then replaced by a smaller number of LHVs carrying the same total payload mass and volume. Four LHV configurations are investigated: an 18.75 m, 46 t longer semi-trailer (LST); 25.25 m, 50 t and 60 t B-doubles and a 34 m, 82 t A-double. Metrics for congestion, freight fleet energy consumption and car energy consumption are defined for comparing the scenarios. Finally, variation of take-up level and LHV engine power for the LST and A-double are investigated. It is concluded that: (a) LHVs should reduce congestion particularly in dense traffic, however, a low mean proportion of freight traffic on UK roads and low take-up levels will limit this effect to be almost negligible; (b) LHVs can significantly improve the energy efficiency of freight fleets, giving up to a 23% reduction in fleet energy consumption at high take-up levels; (c) the small reduction in congestion caused by LHVs could improve the fuel consumption of other road users by up to 3% in dense traffic, however in free-flowing traffic an opposite effect occurs due to higher vehicle speeds and aerodynamic losses; and (d) underpowered LHVs have potential to generate severe congestion, however current manufacturers' recommendations appear suitable. © 2013 IMechE.

Guidewire retention following central venous catheterisation: a human factors and safe design investigation.

BACKGROUND: Central Venous Catheterisation (CVC) has occasionally been associated with cases of retained guidewires in patients after surgery. In theory, this is a completely avoidable complication; however, as with any human procedure, operator error leading to guidewires being occasionally retained cannot be fully eliminated. OBJECTIVE: The work described here investigated the issue in an attempt to better understand it both from an operator and a systems perspective, and to ultimately recommend appropriate safe design solutions that reduce guidewire retention errors. METHODS: Nine distinct methods were used: observations of the procedure, a literature review, interviewing CVC end-users, task analysis construction, CVC procedural audits, two human reliability assessments, usability heuristics and a comprehensive solution survey with CVC end-users. RESULTS: The three solutions that operators rated most highly, in terms of both practicality and effectiveness, were: making trainees better aware of the potential guidewire complications and strongly emphasising guidewire removal in CVC training, actively checking that the guidewire is present in the waste tray for disposal, and standardising purchase of central line sets so that differences that may affect chances of guidewire loss is minimised. CONCLUSIONS: Further work to eliminate/engineer out the possibility of guidewires being retained is proposed.

Assessing the road-damaging potential of heavy vehicles

The relative influence of various heavy vehicle design features on road-damaging potential is discussed. Testing procedures that could be used to measure the road-damaging potential of heavy vehicles are examined. A validated vehicle simulation is used to examine some of the characteristics of dynamic tyre forces generated by typical leaf sprung and air sprung articulated heavy vehicles for typical highway conditions. The proposed EC suspension test is simulated and the results compared with dynamic tyre forces generated under highway conditions. It is concluded that the road-damaging potential of a vehicle cannot be assessed by the simplistic parametric measurement of the proposed EC test. It is questionable whether a vehicle that passes the test will be any more 'road friendly' than one that fails.

Assessing the relative road damaging potential of HGVs

Assessing the road damaging potential of heavy vehicles is becoming an increasingly important issue. In this paper, current vehicle regulations and possible future alternatives are reviewed, and are categorized as tests on individual axles and whole vehicles, and 'direct' and 'indirect' tests. Whole vehicle methods of assessing road damaging potential accurately are then discussed. Direct methods are investigated (focussing on using a force measuring mat), and drawbacks are highlighted. Indirect methods using a transient input applied to individual axles are then examined. Results indicate that if non-linearities are accounted for properly, indirect methods of assessing whole vehicle road damaging potential could offer the required accuracy for a possible future test procedure.