Practical deployment of the brushless doubly-fed machine in a medium scale wind turbine

The Brushless Doubly-Fed Machine (BDFM) is a brushless electrical generator which allows variable speed operation with a power converter rated at only a fraction of the machine rating. This paper details an example implementation of the BDFM in a medium-scale wind turbine. Details of a simplified design procedure based on electrical and magnetic loadings are given along with the results of tests on the manufactured machine. These show that a BDFM of the scale works as expected but that the 4/8 BDFM chosen was slower and thus larger than the turbine's original induction machine. The implementation of the turbine system is discussed, including the vector-based control scheme that ensures the BDFM operates at a demanded speed and the Maximum Power Point Tracking (MPPT) scheme that selects the rotor speed that extracts the most power from the incident wind conditions.

Operating charts for the brushless doubly-fed machine (BDFM)

The Brushless Doubly-Fed Machine (BDFM) is an electrical machine that allows brushless operation in many applications where the Doubly-Fed Induction Generator (DFIG) is currently used. In recent years work on BDFM control means that the machine can now be run stably across its working range. However, little work has been done to define the working area in which BDFM can safely be operated without exceeding its material and stability limits. This paper sets out the theoretical backing for an operating chart of an ideal BDFM similar to that of the synchronous machine. It goes on to show that though the ideal chart gives the right form, non-ideal parameters (especially the finite magnetizing inductances) significantly effect the locations of the limits. Some preliminary experimental data obtained for a 225 frame size machine support the form of the chart. Finally it is shown how the operating chart can be used to chose appropriately sized converters for the BDFM. © 2009 IEEE.

The single-phase brushless doubly-fed machine as a generator for wind turbines

This paper proposes a single-phase variant of the Brushless Doubly-Fed Machine, the Single-Phase BDFM, SPB. Like the BDFM it is a variable speed generator which requires a converter rated at only a fraction of the machine rating, using structure with no brushes. Unlike the BDFM, most of its power is delivered directly into a single-phase grid connection. As such it is a potential replacement for PM generators in small-ish wind turbines, potentially with a much lower cost. In this paper we give details of its operation, with reference to results from the first prototype SPB. We also suggest how it may be controlled, again with experimental results. © 2011 IEEE.

A novel vector control approach for Single Phase Brushless Doubly Fed Machine

This paper proposed a novel control scheme for operating the Single Phase Brushless Doubly-Fed Machine (SPB) based on Stator-Flux-Oriented control algorithm. The SPB is a new type of Brushless Doubly-Fed Machine (BDFM) which shows a potential in applications which require adjustable speed such as Wind Power generation and speed adjustable Drive. The SPB can be applied to single-phase power system and the lower cost of the SPB makes the SPB suitable for low-rated power conversion applications. This paper develops the control scheme of the SPB with explicit mathematical analysis and block diagram of the controller. Experimental verification is also given. © 2011 IEEE.

Implementation of a PI phase angle controller for finite element analysis of the BDFM

Time-stepping finite element analysis of the BDFM for a specific load condition is shown to be a challenging problem because the excitation required cannot be predetermined and the BDFM is not open loops stable for all operating conditions. A simulation approach using feedback control to set the torque and stabilise the BDFM is presented together with implementation details. The performance of the simulation approach is demonstrated with an example and computed results are compared with measurements.

A comparison of cage and nested-loop BDFM rotors

The Brushless Double-Fed Machine (BDFM) is a type of variable speed generator or drive. Using theoretical analysis of simple BDFM rotors this paper establishes trends in how rotor structures determine the rotor's equivalent circuit resistance, leakage inductance and turns ratio. The variation in measured parameters of five prototype rotors is then analysed in light of the trends found. Both the theory and experimental results suggest a significant performance advantage in using cage+loops type rotors as opposed to the simple nested loop type more usually employed.

Noise and vibration in brushless doubly fed machine and brushless doubly fed reluctance machine

This study investigates modes of vibration in brushless doubly fed machine and brushless doubly fed reluctance machine due to the interaction of its fundamental magnetic fields, via the bending forces they set up in the back iron. It is shown that the presence of two field components of different pole numbers leads to vibration components in addition to those that would be expected in single field machines such as the induction motor. Formulations for the frequencies and magnitudes of the expected vibration components are given and verified experimentally. It is shown that the strength of the vibration components is highly dependent on the choice of pole numbers in the machine, with some much worse than equivalent induction machines and some very similar. The methodology presented enables designers to determine whether their machines are likely to suffer from vibration problems in advance of construction, and to apply remedies where appropriate. © The Institution of Engineering and Technology 2014.