Jetting behaviour of polymer solutions in drop-on-demand inkjet printing

The jetting of dilute polymer solutions in drop-on-demand printing is investigated. A quantitative model is presented which predicts three different regimes of behaviour depending upon the jet Weissenberg number Wi and extensibility of the polymer molecules. In regime I (Wi < ½) the polymer chains are relaxed and the fluid behaves in a Newtonian manner. In regime II (½ < Wi < L) where L is the extensibility of the polymer chain the fluid is viscoelastic, but the polymer do not reach their extensibility limit. In regime III (Wi > L) the chains remain fully extended in the thinning ligament. The maximum polymer concentration at which a jet of a certain speed can be formed scales with molecular weight to the power of (1-3ν), (1-6ν) and -2ν in the three regimes respectively, where ν is the solvent quality coefficient. Experimental data obtained with solutions of mono-disperse polystyrene in diethyl phthalate with molecular weights between 24 - 488 kDa, previous numerical simulations of this system, and previously published data for this and another linear polymer in a variety of “good” solvents, all show good agreement with the scaling predictions of the model.

Designing for validation of medical devices and equipment

Validation is important in the design, development and production of medical devices since effective and appropriate validation plays a vital role in defining the success of a product in both technical and economic terms. Regulations and quality standards lay out the requirements for product validation, but it is left to each individual manufacturer to establish and maintain their own validation procedures. More recently, there has also been a change of emphasis in the regulations and standards that encourage the integration of validation into the development process. However, this poses particular challenges to the manufacturer since there is a distinct lack of guidance to assist this integration. This workbook provides the first real guidance on good design practices for medical device development. It has been developed through extensive consultation with device manufacturers and analysis of regulatory requirements. The approach is intended to assist manufacturers in meeting the new regulations.

Prediction of sound emission from open turbulent premixed flames

The sound emission from open turbulent flames is dictated by the two-point spatial correlation of rate of change of fluctuating heat release rate and this correlation has not been investigated directly in the past studies. Turbulent premixed flame data from DNS and laser diagnostics are analyzed to study this correlation function and the two-point spatial correlation of the fluctuating heat release rate. This shows that the correlation functions have simple Gaussian forms whose integral length scale is related to the laminar flame thickness and amplitude depends on the spatial distribution of the time-mean rate of heat release. These results and RANS-CFD solution of open turbulent premixed flames are post-processed to obtain the far field SPL, which agrees well with measured values. © 2010 by the American Institute of Aeronautics and Astronautics, Inc.

Changes of mind in decision-making.

A decision is a commitment to a proposition or plan of action based on evidence and the expected costs and benefits associated with the outcome. Progress in a variety of fields has led to a quantitative understanding of the mechanisms that evaluate evidence and reach a decision. Several formalisms propose that a representation of noisy evidence is evaluated against a criterion to produce a decision. Without additional evidence, however, these formalisms fail to explain why a decision-maker would change their mind. Here we extend a model, developed to account for both the timing and the accuracy of the initial decision, to explain subsequent changes of mind. Subjects made decisions about a noisy visual stimulus, which they indicated by moving a handle. Although they received no additional information after initiating their movement, their hand trajectories betrayed a change of mind in some trials. We propose that noisy evidence is accumulated over time until it reaches a criterion level, or bound, which determines the initial decision, and that the brain exploits information that is in the processing pipeline when the initial decision is made to subsequently either reverse or reaffirm the initial decision. The model explains both the frequency of changes of mind as well as their dependence on both task difficulty and whether the initial decision was accurate or erroneous. The theoretical and experimental findings advance the understanding of decision-making to the highly flexible and cognitive acts of vacillation and self-correction.

Gas properties as a limit to gas turbine performance

Although increasing the turbine inlet temperature has traditionally proved the surest way to increase cycle efficiency, recent work suggests that the performance of future gas turbines may be limited by increased cooling flows and losses. Another limiting scenario concerns the effect on cycle performance of real gas properties at high temperatures. Cycle calculations of uncooled gas turbines show that when gas properties are modelled accurately, the variation of cycle efficiency with turbine inlet temperature at constant pressure ratio exhibits a maximum at temperatures well below the stoichiometric limit. Furthermore, the temperature at the maximum decreases with increasing compressor and turbine polytropic efficiency. This behaviour is examined in the context of a two-component model of the working fluid. The dominant influences come from the change of composition of the combustion products with varying air/fuel ratio (particularly the contribution from the water vapour) together with the temperature variation of the specific heat capacity of air. There are implications for future industrial development programmes, particularly in the context of advanced mixed gas-steam cycles.

Friction of sliding surfaces carrying adsorbed lubricant layers

In concentrated contacts the behaviour of lubricants is much modified by the high local pressures: changes can arise both from molecular ordering within the very thin film lubricant layers present at the interface as well as from the deposition on the component surfaces of more solid-like polymeric boundary layers. These 'third bodies' separating the solid surfaces may have rheological or mechanical properties very different from those observed in the bulk. Classical elasto-hydrodynamic theory considers the entrapped lubricant to exhibit a piezo-viscous behaviour while the conventional picture of more solid boundary lubricant layers views their shear strength r as being linearly dependent on local pressure p, so that T = TO + ap where TO and a are constants. If TO is relatively small, then the coefficient of friction \i = T Ip ~ a and so Amonton's laws are recovered. However, the properties of adsorbed or deposited surface films, or indeed other third bodies such as debris layers, may be more complex than this. A preliminary study has looked quantitatively at the influence of the pressure dependence of the shear strength of any surface layer on the overall friction coefficient of a contact which is made up of an array of asperities whose height varies in a Gaussian manner. Individual contact points may be elastic or plastic. The analysis results in plots of coefficient of friction versus the service or load parameter PIH&NRa where P is the nominal pressure on the contact, HS the hardness of the deforming surface, N the asperity density, R the mean radius of curvature of the asperities, and a is the standard deviation of their height distribution. In principle, any variation oft withp can be incorporated into the model; however, in this initial study we have used data on colloidal suspensions from the group at the Ecole Centrale de Lyon as well as examining the effect of functional relationships of somewhat greater complexity than a simple linear form. Results of the analysis indicate that variations in fj. are possible as the load is varied which depend on the statistical spread of behaviour at individual asperity contacts. The value of this analysis is that it attempts to combine the behaviour of films on the molecular scale with the topography of real engineering surfaces and so give an indication of the effects at the full-size or macro-scale that can be achieved by chemical or molecular surface engineering.

How are internal models of unstable tasks formed?

The results of recent studies suggest that humans can form internal models that they use in a feedforward manner to compensate for both stable and unstable dynamics. To examine how internal models are formed, we performed adaptation experiments in novel dynamics, and measured the endpoint force, trajectory and EMG during learning. Analysis of reflex feedback and change of feedforward commands between consecutive trials suggested a unified model of motor learning, which can coherently unify the learning processes observed in stable and unstable dynamics and reproduce available data on motor learning. To our knowledge, this algorithm, based on the concurrent minimization of (reflex) feedback and muscle activation, is also the first nonlinear adaptive controller able to stabilize unstable dynamics.

Influence of a building's integrated-photovoltaics on heating and cooling loads

Building integrated photovoltaics (BIPV) has the potential to become a major source of renewable energy in the urban environment. BIPV has significant influence on the heat transfer through the building envelope because of the change of the thermal resistance by adding or replacing the building elements. Four different roofs are used to assess the impacts of BIPV on the building's heating-and-cooling loads; namely ventilated air-gap BIPV, non-ventilated (closed) air-gap BIPV, closeroof mounted BIPV, and the conventional roof with no PV and no air gap. One-dimensional transient models of four cases are derived to evaluate the PV performances and building cooling-and-heating loads across the different roofs in order to select the appropriate PV building integration method in Tianjin, China. The simulation results show that the PV roof with ventilated air-gap is suitable for the application in summer because this integration leads to the low cooling load and high PV conversion efficiency. The PV roof with ventilation air-gap has a high time lag and small decrement factor in comparison with other three roofs and has the same heat gain as the cool roof of absorptance 0.4. In winter, BIPV of non-ventilated air gap is more appropriate due to the combination of the low heating-load through the PV roof and high PV electrical output. © 2005 Elsevier Ltd. All rights reserved.