Structure of coexisting liquid phases of supercooled water: analogy with ice polymorphs.

The structural changes occurring in supercooled liquid water upon moving from one coexisting liquid phase to the other have been investigated by computer simulation using a polarizable interaction potential model. The obtained results favorably compare with recent neutron scattering data of high and low density water. In order to assess the physical origin of the observed structural changes, computer simulation of several ice polymorphs has also been carried out. Our results show that there is a strict analogy between the structure of various disordered (supercooled) and ordered (ice) phases of water, suggesting that the occurrence of several different phases of supercooled water is rooted in the same physical origin that is responsible for ice polymorphism.

Airfoil flow and noise computation using monotonically integrated large eddy simulation and acoustic analogy: Effect of the grid resolution.

A new scalable Monotonically Integrated Large Eddy Simulation (MILES) method based on the Compact Accurately Boundary-Adjusting high-REsolution Technique (CABARET) has been applied for the simulation of unsteady flow around NACA0012 airfoil at Re = 400,000 and M = 0.058. The flow solution is coupled with the Ffowcs Williams-Hawkings formulation for far-field noise prediction. The computational modeling results are presented for several computational grid resolutions: 8, 16, and 32 million grid cells and compared with the experimental data available.

Acoustic analogy in swirling mean flow applied to predict rotor trailing-edge noise

The present study aims at accounting for swirling mean flow effects on rotor trailing-edge noise. Indeed, the mean flow in between the rotor and the stator of the fan or of a compressor stage is highly swirling. The extension of Ffowcs-Williams & Hawkings' acoustic analogy in a medium at rest with moving surfaces and of Goldstein's acoustic analogy in a circular duct with uniform mean flow to a swirling mean flow in an annular duct is introduced. It is first applied to tonal noise. In most cases, the swirl modifies the pressure distribution downstream of the fan. In several configurations, when the swirl is rather close to a solid body swirl, it is often sufficient to apply a simple Doppler effect correction when predicting the duct modes in uniform mean flow in order to predict accurately the noise radiated with swirl. However, in other realistic configurations, the swirling mean-flow effect cannot be addressed using this simple Doppler effect correction. Second, a rotor trailing-edge noise model accounting for both the effects of the annular duct and the swirling mean flow is developed and applied to a realistic fan rotor with different swirling and sheared mean flows (and as a result different associated blade stagger angles). The benchmark cases are built from the Boeing 18-inch Fan Rig Broadband Noise Test. In all cases the swirling mean flow has an effect. In some cases the a simple Doppler effect may address it, but, in other realistic configurations our acoustic analogy with swirl is needed. © 2012 by the authors. Published by the American Institute of Aeronautics and Astronautics, Inc.

The acoustic analogy in an annular duct with swirling mean flow

This paper is concerned with modelling the effects of swirling flow on turbomachinery noise. We develop an acoustic analogy to predict sound generation in a swirling and sheared base flow in an annular duct, including the presence of moving solid surfaces to account for blade rows. In so doing we have extended a number of classical earlier results, including Ffowcs Williams & Hawkings' equation in a medium at rest with moving surfaces, and Lilley's equation for a sheared but non-swirling jet. By rearranging the Navier-Stokes equations we find a single equation, in the form of a sixth-order differential operator acting on the fluctuating pressure field on the left-hand side and a series of volume and surface source terms on the right-hand side; the form of these source terms depends strongly on the presence of swirl and radial shear. The integral form of this equation is then derived, using the Green's function tailored to the base flow in the (rigid) duct. As is often the case in duct acoustics, it is then convenient to move into temporal, axial and azimuthal Fourier space, where the Green's function is computed numerically. This formulation can then be applied to a number of turbomachinery noise sources. For definiteness here we consider the noise produced downstream when a steady distortion flow is incident on the fan from upstream, and compare our results with those obtained using a simplistic but commonly used Doppler correction method. We show that in all but the simplest case the full inclusion of swirl within an acoustic analogy, as described in this paper, is required. © 2013 Cambridge University Press.

Convective heat dissipation with lattice-frame materials

This paper presents experimental results on heat transfer and pressure drop for a compact heat sink made of fully triangulated, lightweight (porosity∼0.938), aluminum lattice-frame materials (LFMs). Due to the inherent structural anisotropy of the LFMs, two mutually perpendicular orientations were selected for the measurements. Constant heat flux was applied to the heat sink under steady state conditions, and dissipated by forced air convection. The experimental data were compared with those predicted from an analytical model based on fin analogy. The experimental results revealed that pressure drop is strongly dependent upon the orientation of the structure, due mainly to the flow blockage effect. For heat transfer measurements, typical local temperature distributions on the substrate under constant heat flux conditions were captured with infrared camera. The thermal behavior of LFMs was found to follow closely that of cylinder banks, with early transition Reynolds number (based on strut diameter) equal to about 300. The Nusselt number prediction from the fin-analogy correlates well with experimental measurements, except at low Reynolds numbers where a slightly underestimation is observed. Comparisons with empty channels and commonly used heat exchanger media show that the present LFM heat sink can remove heat approximately seven times more efficient than an empty channel and as efficient as a bank of cylinders at the same porosity level. The aluminum LFMs are extremely stiff and strong, making them ideal candidates for multifunctional structures requiring both heat dissipation and mechanical load carrying capabilities. © 2003 Elsevier Ltd. All rights reserved.

Understanding jet noise.

Jets are one of the most fascinating topics in fluid mechanics. For aeronautics, turbulent jet-noise modelling is particularly challenging, not only because of the poor understanding of high Reynolds number turbulence, but also because of the extremely low acoustic efficiency of high-speed jets. Turbulent jet-noise models starting from the classical Lighthill acoustic analogy to state-of-the art models were considered. No attempt was made to present any complete overview of jet-noise theories. Instead, the aim was to emphasize the importance of sound generation and mean-flow propagation effects, as well as their interference, for the understanding and prediction of jet noise.

On computing the physical sources of jet noise

We derive a closed system of equations that relates the acoustically radiating flow variables to the sources of sound for homentropic flows. We use radiating density, momentum density and modified pressure as the dependent variables which leads to simple source terms for the momentum equations. The source terms involve the non-radiating parts of the density and momentum density fields. These non-radiating components are obtained by removing the radiating wavenumbers in the Fourier domain. We demonstrate the usefulness of this new technique on an axi-symmetric jet solution of the Navier-Stokes equations, obtained by direct numerical simulation (DNS). The dominant source term is proportional to the square of the non-radiating part of the axial momentum density. We compare the sound sources to that obtained by an acoustic analogy and find that they have more realistic physical properties. Their frequency content and amplitudes are consistent with. We validate the sources by computing the radiating sound field and comparing it to the DNS solution. © 2010 by S. Sinayoko, A. Agarwal.

Once again on the importance of propagation effects for jet noise modelling

Several turbulent jet noise models starting from the classical Lighthill acoustic analogy to state-of-the art models are considered. No attempt is made to present any complete overview of jet noise theories. Instead, the aim is to emphasise the importance of sound generation and meanflow effects for the understanding and prediction of jet noise. For a recent acoustic analogy model, the consequences of jet flow simplification on the predicted sound spectra shape and the effective noise source location in the jet are discussed. © 2010 by the American Institute of Aeronautics and Astronautics, Inc.

Classification and choice in product design

Life is full of difficult choices. Everyone has their own way of dealing with these, some effective, some not. The problem is particularly acute in engineering design because of the vast amount of information designers have to process. This paper deals with a subset of this set of problems: the subset of selecting materials and processes, and their links to the design of products. Even these, though, present many of the generic problems of choice, and the challenges in creating tools to assist the designer in making them. The key elements are those of classification, of indexing, of reaching decisions using incomplete data in many different formats, and of devising effective strategies for selection. This final element - that of selection strategies - poses particular challenges. Product design, as an example, is an intricate blend of the technical and (for want of a better word) the aesthetic. To meet these needs, a tool that allows selection by analysis, by analogy, by association and simply by 'browsing' is necessary. An example of such a tool, its successes and remaining challenges, will be described.