Boundary-layer suction system design for laminar-flying-wing aircraft

The present study aims to provide insight into the parameters affecting practical laminar-flow-control suction power requirements for a commercial laminar-flying-wing transport aircraft. It is shown that there is a minimum power requirement independent of the suction system design, associated with the stagnation pressure loss in the boundary layer. This requirement increases with aerofoil section thickness, but depends only weakly on Mach number and (for a thick, lightly loaded laminar flying wing) lift coefficient. Deviation from the optimal suction distribution, due to a practical chamber-based architecture, is found to have very little effect on the overall suction coefficient; hence, to a good approximation, the power penalty is given by the product of the optimal suction flow rate coefficient and the average skin pressure drop. In the spanwise direction, through suitable choice of chamber depth, the pressure drop due to frictional and inertial effects may be rendered negligible. Finally, if there are fewer pumps than chambers, the average pressure drop from the aerofoil surface to the pump collector ducts, rather than to the chambers, determines the power penalty. For the representative laminar-flying-wing aircraft parameters considered here, the minimum power associated with boundary-layer losses alone contributes some 80-90% of the total power requirement. © 2011 by the American Institute of Aeronautics and Astronautics, Inc.

Redesigning the design process through interactive simulation: A case study of life-cycle engineering in jet engine conceptual design

Many aerospace companies are currently making the transition to providing fully-integrated product-service offerings in which their products are designed from the outset with life-cycle considerations in mind. Based on a case study at Rolls-Royce, Civil Aerospace, this paper demonstrates how an interactive approach to process simulation can be used to support the redesign of existing design processes in order to incorporate life-cycle engineering (LCE) considerations. The case study provides insights into the problems of redesigning the conceptual stages of a complex, concurrent engineering design process and the practical value of process simulation as a tool to support the specification of process changes in the context of engineering design. The paper also illustrates how development of a simulation model can provide significant benefit to companies through the understanding of process behaviour that is gained through validating the behaviour of the model using different design and iteration scenarios. Keywords: jet engine design; life-cycle engineering; LCE; process change; design process simulation; applied signposting model; ASM. Copyright © 2011 Inderscience Enterprises Ltd.

Simulating intertwined design processes that have similar structures: A case study of a small company that creates made-to-order fashion products

The authors use simulation to analyse the resource-driven dependencies between concurrent processes used to create customised products in a company. Such processes are uncertain and unique according to the design changes required. However, they have similar structures. For simulation, a level of abstraction is chosen such that all possible processes are represented by the same activity network. Differences between processes are determined by the customisations that they implement. The approach is illustrated through application to a small business that creates customised fashion products. We suggest that similar techniques could be applied to study intertwined design processes in more complex domains. Copyright © 2011 Inderscience Enterprises Ltd.

Security considerations in the design and peering of RFID discovery services

There is growing interest in Discovery Services for locating RFID and supply chain data between companies globally, to obtain product lifecycle information for individual objects. Discovery Services are heralded as a means to find serial-level data from previously unknown parties, however more realistically they provide a means to reduce the communications load on the information services, the network and the requesting client application. Attempts to design a standardised Discovery Service will not succeed unless security is considered in every aspect of the design. In this paper we clearly show that security cannot be bolted-on in the form of access control, although this is also required. The basic communication model of the Discovery Service critically affects who shares what data with whom, and what level of trust is required between the interacting parties. © 2009 IEEE.

An evaluation of a new product data model

Engineering companies face many challenges today such as increased competition, higher expectations from consumers and decreasing product lifecycle times. This means that product development times must be reduced to meet these challenges. Concurrent engineering, reuse of engineering knowledge and the use of advanced methods and tools are among the ways of reducing product development times. Concurrent engineering is crucial in making sure that the products are designed with all issues considered simultaneously. The reuse of engineering knowledge allows existing solutions to be reused. It can also help to avoid the mistakes made in previous designs. Computer-based tools are used to store information, automate tasks, distribute work, perform simulation and so forth. This research concerns the evaluation of tools that can be used to support the design process. These tools are evaluated in terms of the capture of information generated during the design process. This information is vital to allow the reuse of knowledge. Present CAD systems store only information on the final definition of the product such as geometry, materials and manufacturing processes. Product Data Management (PDM) systems can manage all this CAD information along with other product related information. The research includes the evaluation of two PDM systems, Windchill and Metaphase, using the design of a single-handed water tap as a case study. The two PDMs were then compared to PROSUS/DDM. PROSUS is the Process-Based Support System proposed by [Blessing 94] using the same case study. The Design Data Model is the product data model that includes PROSUS. The results look promising. PROSUS/DDM is able to capture most design information and structure and present it logically. The design process and product information is related and stored within the DDM structure. The PDMs can capture most design information, but information from early stages of design is stored only as unstructured documentation. Some problems were found with PROSUS/DDM. A proposal is made that may make it possible to resolve these problems, but this will require further research.

Towards the development of an integrated design framework using the Blackboard model

Current research into the process of engineering design is extending the use of computers towards the acquisition, representation and application of design process knowledge in addition to the existing storage and manipulation of product-based models of design objects. This is a difficult task because the design of mechanical systems is a complex, often unpredictable process involving ill-structured problem solving skills and large amounts of knowledge, some which may be of an incomplete and subjective nature. Design problems require the integration of a variety of modes of working such as numerical, graphical, algorithmic or heuristic and demand products through synthesis, analysis and evaluation activities.

This report presents the results of a feasibility study into the blackboard approach and discusses the development of an initial prototype system that will enable an alphanumeric design dialogue between a designer and an expert to be analysed in a formal way, thus providing real-life protocol data on which to base the blackboard message structures.

Product Service Systems and supply network relationships: An exploratory case study

Purpose - In recent years there has been increasing interest in Product Service Systems (PSSs) as a business model for selling integrated product and service offerings. To date, there has been extensive research into the benefits of PSS to manufacturers and their customers, but there has been limited research into the effect of PSS on the upstream supply chain. This paper seeks to address this gap in the research. Design/methodology/approach - The research uses case-based research which is appropriate for exploratory research of this type. In-depth interviews were conducted with key personnel in a focal firm and two members of its supply chain, and the results were analysed to identify emergent themes.b Findings - The research has identified differences in supplier behaviour dependent on their role in PSS delivery and their relationship with the PSS provider. In particular, it suggests that for a successful partnership it is important to align the objectives between PSS provider and suppliers. Originality/value - This research provides a detailed investigation into a PSS supply chain and highlights the complexity of roles and relationships among the organizations within it. It will be of value to other PSS researchers and organizations transitioning to the delivery of PSS. © Emerald Group Publishing Limited.

Industrialization as a key element of sustainable product-service solutions

Product-service systems are seen by many authors to offer potential for significant sustainability benefit. Manufacturing companies are said to be essential to such a change through their influence over product performance and over the use and end-of-life stages. Yet linking these stages such that the producer is incentivized to improve the performance of later stages is still a challenge. This paper argues for placing the producer at the centre of a new arrangement: by seeking to utilize the producer's knowledge of designing and the knowledge of volume production, through creation of platforms, while cooperating closely with other actors. The paper describes three case studies that have used such an approach to design and implement new food production systems. Based on 12 months of action research observations, 10 participating organizations from the cases were studied, and the implemented solutions assessed for environmental, economic and social performance. The results demonstrate a high level of sustainability benefit is achievable using platforms and partners to design product-service systems, while highlighting that changes to production arrangements are necessary but not sufficient to improve whole life-cycle environmental performance of product-service systems, and that producers need to cooperate closely with other actors to achieve the claimed benefits.

Environmental priorities in strategic product development

This paper reports some results from a major research project on the integration of environmental issues into design in the electrical and electronic industry. Product development practice and ecodesign methods were examined along with qualitative data from 19 manufacturers, using interviews and an action research methodology. A four-stage framework for ecodesign practice resulted: first, to make an environmental assessment from a life cycle viewpoint; then to communicate the analysis and collect feedback; thirdly to prioritize the environmental issues and finally to complete the design using relevant tools and methods. This 'ARPI' framework (analyse, report, prioritize, improve) applies to both strategic and operational levels. Initial testing of the framework in collaborating companies highlighted difficulties with communication with design teams; the role of 'ecodesign champions' is explained. Other challenges are the development of customized tools and the training of designers. The study concludes that the prioritization step is critical, as it simplifies and clarifies the tasks in design that take place after formulation of the specification. Copyright (C) 2000 John Wiley and Sons, Ltd. and ERP Environment.