Simulation in user-centred design: Helping designers to empathise with atypical users

Time and budget constraints frequently prevent designers from consulting with end-users while assessing the ease of use of the products they create. This has resulted in solutions that are difficult to use by a wide range of users, especially the growing older adult population and people with different types of impairments. To help designers with this problem, capability-loss simulators have been developed with the aim of temporarily representing users who are otherwise difficult to access. This paper questions the reliability of existing tools in providing designers with meaningful information about the users' capabilities. Consequently, a new capability-loss simulation toolkit is presented, followed by its empirical evaluation. The new toolkit proved to be significantly helpful for a group of designers identifying real usability problems with everyday devices. © 2012 Copyright Taylor and Francis Group, LLC.

Bias-free identification of a linear model-predictive steering controller from measured driver steering behavior

Recent developments in modeling driver steering control with preview are reviewed. While some validation with experimental data has been presented, the rigorous application of formal system identification methods has not yet been attempted. This paper describes a steering controller based on linear model-predictive control. An indirect identification method that minimizes steering angle prediction error is developed. Special attention is given to filtering the prediction error so as to avoid identification bias that arises from the closed-loop operation of the driver-vehicle system. The identification procedure is applied to data collected from 14 test drivers performing double lane change maneuvers in an instrumented vehicle. It is found that the identification procedure successfully finds parameter values for the model that give small prediction errors. The procedure is also able to distinguish between the different steering strategies adopted by the test drivers. © 2006 IEEE.

Designing inclusive interfaces through user modeling and simulation

Elderly and disabled people can be hugely benefited through the advancement of modern electronic devices, as those can help them to engage more fully with the world. However, existing design practices often isolate elderly or disabled users by considering them as users with special needs. This article presents a simulator that can reflect problems faced by elderly and disabled users while they use computer, television, and similar electronic devices. The simulator embodies both the internal state of an application and the perceptual, cognitive, and motor processes of its user. It can help interface designers to understand, visualize, and measure the effect of impairment on interaction with an interface. Initially a brief survey of different user modeling techniques is presented, and then the existing models are classified into different categories. In the context of existing modeling approaches the work on user modeling is presented for people with a wide range of abilities. A few applications of the simulator, which shows the predictions are accurate enough to make design choices and point out the implication and limitations of the work, are also discussed. © 2012 Copyright Taylor and Francis Group, LLC.

Light-bias induced instability and persistent photoconductivity in In-Zn-O/Ga-In-Zn-O thin film transistors

Stress/recovery measurements demonstrate that even high-performance passivated In-Zn-O/ Ga-In-Zn-O thin film transistors with excellent in-dark stability suffer from light-bias induced threshold voltage shift (ΔV T) and defect density changes. Visible light stress leads to ionisation of oxygen vacancy sites, causing persistent photoconductivity. This makes the material act as though it was n-doped, always causing a negative threshold voltage shift under strong illumination, regardless of the magnitude and polarity of the gate bias.

Design for inclusivity: A practical guide to accessible, innovative and user-centred design

Design for Inclusivity is a guide to inclusive design for all types of designers, providing guidelines, real examples and information sources.

Understandable by design: How can products be designed to align with user experience?

Chapter 14 Understandable by Design: How Can Products be Designed to Align with User Experience? A. Mieczakowski, PM Langdon, RH Bracewell, JJ Patmore and PJ Clarkson 14.1 Introduction Understanding users increases the likelihood that ...

Clustering user data for user modelling in the GUIDE multi-modal set-top box

Chapter 20 Clustering User Data for User Modelling in the GUIDE Multi-modal Set- top Box PM Langdon and P. Biswas 20.1 ... It utilises advanced user modelling and simulation in conjunction with a single layer interface that permits a ...

P-16: Light-bias induced instability and persistent photoconductivity in in-zn-o/ga-in-zn-o thin film transistors

Stress/recovery measurements demonstrate that even highperformance passivated In-Zn-O/ Ga-In-Zn-O thin film transistors with excellent in-dark stability suffer from light-bias induced threshold voltage shift (ΔV T) and defect density changes. Visible light stress leads to ionisation of oxygen vacancy sites, causing persistent photoconductivity. This makes the material act as though it was n-doped, always causing a negative threshold voltage shift under strong illumination, regardless of the magnitude and polarity of the gate bias. © 2011 SID.

Comparison of manual and user guided methodologies for the classification and retrieval of construction site images

The amount of original imaging information produced yearly during the last decade has experienced a tremendous growth in all industries due to the technological breakthroughs in digital imaging and electronic storage capabilities. This trend is affecting the construction industry as well, where digital cameras and image databases are gradually replacing traditional photography. Owners demand complete site photograph logs and engineers store thousands of images for each project to use in a number of construction management tasks like monitoring an activity's progress and keeping evidence of the "as built" in case any disputes arise. So far, retrieval methodologies are done manually with the user being responsible for imaging classification according to specific rules that serve a limited number of construction management tasks. New methods that, with the guidance of the user, can automatically classify and retrieve construction site images are being developed and promise to remove the heavy burden of manually indexing images. In this paper, both the existing methods and a novel image retrieval method developed by the authors for the classification and retrieval of construction site images are described and compared. Specifically a number of examples are deployed in order to present their advantages and limitations. The results from this comparison demonstrates that the content based image retrieval method developed by the authors can reduce the overall time spent for the classification and retrieval of construction images while providing the user with the flexibility to retrieve images according different classification schemes.

Real user evaluation of spoken dialogue systems using Amazon Mechanical Turk

This paper describes a framework for evaluation of spoken dialogue systems. Typically, evaluation of dialogue systems is performed in a controlled test environment with carefully selected and instructed users. However, this approach is very demanding. An alternative is to recruit a large group of users who evaluate the dialogue systems in a remote setting under virtually no supervision. Crowdsourcing technology, for example Amazon Mechanical Turk (AMT), provides an efficient way of recruiting subjects. This paper describes an evaluation framework for spoken dialogue systems using AMT users and compares the obtained results with a recent trial in which the systems were tested by locally recruited users. The results suggest that the use of crowdsourcing technology is feasible and it can provide reliable results. Copyright © 2011 ISCA.