Vortices, sound and flames - a damaging combination

The interaction between vortices, sound and combustion can lead to self-excited oscillations of such large amplitudes that structural damage is done. These occur because any small unsteadiness in the rate of combustion is a source of sound, generating pressure and velocity fluctuations. However, the velocity fluctuations perturb the flame, thereby altering the instantaneous rate of heat release. Instability is then possible because while acoustic waves perturb the combustion, the unsteady combustion generates yet more sound! Combustion oscillations can occur in afterburners and at idle in conventional aeroengine combustors. Lean premixed, prevapourized technology has tremendous potential to reduce NOx emissions, but is proving highly susceptible to self-excited oscillations. An overview of the physics of the interaction between vortices, sound and flames is presented, and illustrated by examples of instability in generic premixed ducted flames and in aeroengine combustors. The potential for both passive and active control is discussed.

Spray visualisation and acoustic analysis in a gas-turbine type burner

This paper presents the characterisation of self-excited oscillations in a kerosene burner. The combustion instability exhibits two different modes and frequencies depending on the air flow rate. Experimental results reveal the influence of the spray to shift between these two modes. Pressure and heat release fluctuations have been measured simultaneously and the flame transfer function has been calculated from these measurements. The Mie scattering technique has been used to record spray fluctuations in reacting conditions with a high speed camera. Innovative image processing has enabled us to obtain fluctuations of the Mie scattered light from the spray as a temporal signal acquired simultaneously with pressure fluctuations. This has been used to determine a transfer function relating the image intensity and hence the spray fluctuations to changes in air velocity. This function has identified the different role the spray plays in the two modes of instability. At low air flow rates, the spray responds to an unsteady air flow rate and the time varying spray characteristics lead to unsteady combustion. At higher air flow rates, effective evaporation means that the spray dynamics are less important, leading to a different flame transfer function and frequency of self-excited oscillation. In conclusion, the combustion instabilities observed are closely related with the fluctuations of the spray motion and evaporation.

Microstructural optimization of cellular acoustic materials

A microstructure based acoustic model is introduced, which can be used to optimize the microstructure of cellular materials and thus to obtain their optimal acoustic property. This acoustic model is an unsteady one which is appropriate in the limit of low Reynolds numbers. The model involves three elements. This first involves the propagation of acoustic waves passing the cylinders whose axes are aligned parallel to the direction of propagation. The second model relates to the propagation of acoustic waves passing the cylinders whose axes are aligned perpendicular to the direction of propagation. In both cases the interaction between adjacent cylinders is taken into account by considering the effect of polygonal periodic boundary conditions. As these two models are linear they are combined to give the characteristics of propagation at arbitrary incidence. The third model involves propagation passing spheres in order to represent the joints. Heat transfer is also included. These three models are then used to expand the design space and calculate the optimum cell structure for desired acoustic performance in a number of different applications. Moreover, the application fields are also analyzed.

The calculation of acoustic shielding of engine noise by the Silent Aircraft Airframe

The Silent Aircraft airframe has a flying wing design with a large wing planform and a propulsion system embedded in the rear of the airframe with intake on the upper surface of the wing. In the present paper, boundary element calculations are presented to evaluate acoustic shielding at low frequencies. Besides the three-dimensional geometry of the Silent Aircraft airframe, a few two-dimensional problems are considered that provide some physical insight into the shielding calculations. Mean flow refraction effects due to forward flight motion are accounted for by a simple time transformation that decouples the mean-flow and acoustic-field calculations. It is shown that significant amount of shielding can be obtained in the shadow region where there is no direct line of sight between the source and observer. The boundary element solutions are restricted to low frequencies. We have used a simple physically-based model to extend the solution to higher frequencies. Based on this model, using a monopole acoustic source, we predict at least an 18 dBA reduction in the overall sound pressure level of forward-propagating fan noise because of shielding.

Analytical approximations for the modal acoustic impedances of simply supported, rectangular plates.

Coupling of the in vacuo modes of a fluid-loaded, vibrating structure by the resulting acoustic field, while known to be negligible for sufficiently light fluids, is still only partially understood. A particularly useful structural geometry for the study of this problem is the simply supported, rectangular flat plate, since it exhibits all the relevant physical features while still admitting an analytical description of the modes. Here the influence of the fluid can be expressed in terms of a set of doubly infinite integrals over wave number: the modal acoustic impedances. Closed-form solutions for these impedances do not exist and, while their numerical evaluation is possible, it greatly increases the computational cost of solving the coupled system of modal equations. There is thus a need for accurate analytical approximations. In this work, such approximations are sought in the limit where the modal wavelength is small in comparison with the acoustic wavelength and the plate dimensions. It is shown that contour integration techniques can be used to derive analytical formulas for this regime and that these formulas agree closely with the results of numerical evaluations. Previous approximations [Davies, J. Sound Vib. 15(1), 107-126 (1971)] are assessed in the light of the new results and are shown to give a satisfactory description of real impedance components, but (in general) erroneous expressions for imaginary parts.

Options for achieving a 50% cut in industrial carbon emissions by 2050.

Carbon emissions from industry are dominated by production of goods in steel, cement plastic, paper, and aluminum. Demand for these materials is anticipated to double at least by 2050, by which time global carbon emissions must be reduced by at least 50%. To evaluate the challenge of meeting this target the global flows of these materials and their associated emissions are projected to 2050 under five technical scenarios. A reference scenario includes all existing and emerging efficiency measures but cannot provide sufficient reduction. The application of carbon sequestration to primary production proves to be sufficient only for cement The emissions target can always be met by reducing demand, for instance through product life extension, material substitution, or "light-weighting". Reusing components shows significant potential particularly within construction. Radical process innovation may also be possible. The results show that the first two strategies, based on increasing primary production, cannot achieve the required emissions reductions, so should be balanced by the vigorous pursuit of material efficiency to allow provision of increased material services with reduced primary production.