Fundamental atrium design for natural ventilation

An atrium is a central feature of many modern naturally ventilated building designs. The atrium fills with warm air from the adjoining storeys: this air may be further warmed by direct solar heating in the atrium, and the deep warm layer enhances the flow. In this paper we focus on the degree of flow enhancement achieved by an atrium which is itself 'ventilated' directly, by a low-level connection to the exterior. A theoretical model is developed to predict the steady stack-driven displacement flow and thermal stratification in the building, due to heat gains in the storey and solar gains in the atrium, and compared with the results of laboratory experiments. Direct ventilation of the atrium is detrimental to the ventilation of the storey and the best design is identified as a compromise that provides adequate ventilation of both spaces. We identify extremes of design for which an atrium provides no significant enhancement of the flow, and show that an atrium only enhances the flow in the storey if its upper opening is of an intermediate size, and its lower opening is sufficiently small. © 2003 Elsevier Science Ltd. All rights reserved.

The effects of operational and design parameters on the tolerance of ADSR fuel pin cladding to beam interruptions

This paper investigates the effects of design parameters, such as cladding and coolant material choices, and operational phenomena, such as creep and fission product decay heat, on the tolerance of Accelerator Driven Subcritical Reactor (ADSR) fuel pin cladding to beam interruptions. This work aims to provide a greater understanding of the integration between accelerator and nuclear reactor technologies in ADSRs. The results show that an upper limit on cladding operating temperature of 550 °C is appropriate, as higher values of temperature tend to accelerate creep, leading to cladding failure much sooner than anticipated. The effect of fission product decay heat is to reduce significantly the maximum stress developed in the cladding during a beam-trip-induced transient. The potential impact of irradiation damage and the effects of the liquid metal coolant environment on the cladding are discussed. © 2013 Elsevier Ltd. All rights reserved.

Phase perfection in zinc Blende and Wurtzite III-V nanowires using basic growth parameters.

Controlling the crystallographic phase purity of III-V nanowires is notoriously difficult, yet this is essential for future nanowire devices. Reported methods for controlling nanowire phase require dopant addition, or a restricted choice of nanowire diameter, and only rarely yield a pure phase. Here we demonstrate that phase-perfect nanowires, of arbitrary diameter, can be achieved simply by tailoring basic growth parameters: temperature and V/III ratio. Phase purity is achieved without sacrificing important specifications of diameter and dopant levels. Pure zinc blende nanowires, free of twin defects, were achieved using a low growth temperature coupled with a high V/III ratio. Conversely, a high growth temperature coupled with a low V/III ratio produced pure wurtzite nanowires free of stacking faults. We present a comprehensive nucleation model to explain the formation of these markedly different crystal phases under these growth conditions. Critical to achieving phase purity are changes in surface energy of the nanowire side facets, which in turn are controlled by the basic growth parameters of temperature and V/III ratio. This ability to tune crystal structure between twin-free zinc blende and stacking-fault-free wurtzite not only will enhance the performance of nanowire devices but also opens new possibilities for engineering nanowire devices, without restrictions on nanowire diameters or doping.

Kelvin-Helmholtz-like instabilities in turbulent flows over complex surfaces

Riblets are small surface protrusions aligned with the flow direction, which confer an anisotropic roughness to the surface [6]. We have recently reported that the transitional-roughness effect in riblets, which limits their performance, is due to a Kelvin–Helmholtz-like instability of the overlying mean flow [7]. According to our DNSs, the instability sets on as the Reynolds number based on the roughness size of the riblets increases, and coherent, elongated spanwise vortices begin to develop immediately above the riblet tips, causing the degradation of the drag-reduction effect. This is a very novel concept, since prior studies had proposed that the degradation was due to the interaction of riblets with the flow as independent units, either to the lodging of quasi-streamwise vortices in the surface grooves [2] or to the shedding of secondary streamwise vorticity at the riblet peaks [9]. We have proposed an approximate inviscid analysis for the instability, in which the presence of riblets is modelled through an average boundary condition for an overlying, spanwise-independent mean flow. This simplification lacks the accuracy of an exact analysis [4], but in turn applies to riblet surfaces in general. Our analysis succeeds in predicting the riblet size for the onset of the instability, while qualitatively reproducing the wavelengths and shapes of the spanwise structures observed in the DNSs. The analysis also connects the observations with the Kelvin–Helmholtz instability of mixing layers. The fundamental riblet length scale for the onset of the instability is a ‘penetration length,’ which reflects how easily the perturbation flow moves through the riblet grooves. This result is in excellent agreement with the available experimental evidence, and has enabled the identification of the key geometric parameters to delay the breakdown. Although the appearance of elongated spanwise vortices was unexpected in the case of riblets, similar phenomena had already been observed over other rough [3], porous [1] and permeable [11] surfaces, as well as over plant [5,14] and urban [12] canopies, both in the transitional and in the fully-rough regimes. However, the theoretical analyses that support the connection of these observations with the Kelvin–Helmholtz instability are somewhat scarce [7, 11, 13]. It has been recently proposed that Kelvin–Helmholtz-like instabilities are a dominant feature common to “obstructed” shear flows [8]. It is interesting that the instability does not require an inflection point to develop, as is often claimed in the literature. The Kelvin-Helmholtz rollers are rather triggered by the apparent wall-normal-transpiration ability of the flow at the plane immediately above the obstructing elements [7,11]. Although both conditions are generally complementary, if wall-normal transpiration is not present the spanwise vortices may not develop, even if an inflection point exists within the roughness [10]. REFERENCES [1] Breugem, W. P., Boersma, B. J. & Uittenbogaard, R. E. 2006 J. Fluid Mech. 562, 35–72. [2] Choi, H., Moin, P. & Kim, J. 1993 J. Fluid Mech. 255, 503–539. [3] Coceal, O., Dobre, A., Thomas, T. G. & Belcher, S. E. 2007 J. Fluid Mech. 589, 375–409. [4] Ehrenstein, U. 2009 Phys. Fluids 8, 3194–3196. [5] Finnigan, J. 2000 Ann. Rev. Fluid Mech. 32, 519–571. [6] Garcia-Mayoral, R. & Jimenez, J. 2011 Phil. Trans. R. Soc. A 369, 1412–1427. [7] Garcia-Mayoral, R. & Jimenez, J. 2011 J. Fluid Mech. doi: 10.1017/jfm.2011.114. [8] Ghisalberti, M. 2009 J. Fluid Mech. 641, 51–61. [9] Goldstein, D. B. & Tuan, T. C. 1998 J. Fluid Mech. 363, 115–151. [10] Hahn, S., Je, J. & Choi, H. 2002 J. Fluid Mech. 450, 259–285. [11] Jimenez, J., Uhlman, M., Pinelli, A. & G., K. 2001 J. Fluid Mech. 442, 89–117. [12] Letzel, M. O., Krane, M. & Raasch, S. 2008 Atmos. Environ. 42, 8770–8784. [13] Py, C., de Langre, E. & Moulia, B. 2006 J. Fluid Mech. 568, 425–449. [14] Raupach, M. R., Finnigan, J. & Brunet, Y. 1996 Boundary-Layer Meteorol. 78, 351–382.

A canonical normal SBLI flow relevant to external compression inlets

The normal shock wave / boundary layer interaction (normal SBLI) is important to the operation and performance of a supersonic inlet, and the normal SBLI is particularly prominent in external compression inlets. To improve our understanding of such interactions, it is helpful to make use of fundamental flows which capture the main elements of inlets, without resorting to the level of complexity and system integration associated with full-geometry inlets. In this paper, several fundamental fiow-fleld configurations have been considered as possible test cases to represent the normal SBLI aspects found in typical external compression inlets, and it was found that the spillage-diffuser more closely retains the basic flow features of an external compression inlet than the other configurations. In particular, this flow-fleld allows the normal shock Mach number as well as the amount and rate of subsonic diffusion to be all held approximately constant mid independent of the application of flow control. In addition, a survey of several external compression inlets was conducted to quantify the flow and geometric parameters of the spillage-diffuser relevant to actual inlets. The results indicated that such a flow may be especially relevant if the terminal Mach number is about 1.3 to 1.4, the confinement parameter is around 10%, the width around twice or three times the height, and with the area expansion just downstream of the shock on the conservative side of the stall limit for incompressible diffusers. © 2013 by the American Institute of Aeronautics and Astronautics, Inc. All rights reserved.

Canonical normal shock wave/boundary-layer interaction flows relevant to external compression inlets

The normal shock wave/boundary-layer interaction is important to the operation and performance of a supersonic inlet, and the normal shock wave/boundary-layer interaction is particularly prominent in external compression inlets. To improve understanding of such interactions, it is helpful to make use of fundamental flows that capture the main elements of inlets, without resorting to the level of complexity and system integration associated with full-geometry inlets. In this paper, several fundamental flowfield configurations have been considered as possible test cases to represent the normal shock wave/boundary-layer interaction aspects found in typical external compression inlets, and it was found that the spillage diffuser more closely retains the basic flow features of an external compression inlet than the other configurations. In particular, this flowfield allows the normal shock Mach number as well as the amount and rate of subsonic diffusion to all be held approximately constant and independent of the application of flow control. In addition, a survey of several external compression inlets was conducted to quantify the flow and geometric parameters of the spillage diffuser relevant to actual inlets. The results indicated that such a flow may be especially relevant if the terminal Mach number is about 1.3 to 1.4, the confinement parameter is around 10%, and the width is around twice or three times the height. In addition, the area expansion downstream of the shock should be limited to the conservative side of incipient stall based on incompressible diffusers. Copyright © 2013 by the authors.

Ultrashort pulse generation in diode lasers

The basic ideas and current state of the art of ultrashort pulse generation by injection lasers are reviewed. All developed techniques, including gain switching, Q-switching, and mode-locking are described and compared. A simple theoretical treatment of a diode laser which emits picosecond light pulses is discussed. Some fundamental limits of the pulse parameters are discussed. Finally, compression of chirped optical pulses by optical fibres and the soliton effect is considered. © 1992 Chapman & Hall.

Design trade-offs for energy regeneration and control in vehicle suspensions

This paper investigates the fundamental trade-offs involved in designing energy-regenerative suspensions, in particular, focusing on efficiency of power extraction and its effect on vehicle dynamics and control. It is shown that typical regenerative devices making use of linear-to-rotational elements can be modelled as a parallel arrangement of an inerter and a dissipative admittance. Taking account of typical adjustable parameters of the generator, it is shown, for a given suspension damping coefficient, that the power efficiency ratio scales with inertance. For a typical passenger vehicle, it is shown that there is a feasible compromise, namely that good efficiency is achievable with an inertance value that is not detrimental to vehicle performance. A prototype is designed and tested with a resistive termination and experimental results show good agreement between ideal and experimental admittances. The possibility to use dynamic (rather than purely resistive) loads to improve vehicle control without limiting the energy recovery is discussed. © 2013 Copyright Taylor and Francis Group, LLC.

Numerical modelling of chirality-Induced bi-Directional swimming of artificial flagella

Biomimetic micro-swimmers can be used for various medical applications, such as targeted drug delivery and micro-object (e.g. biological cells) manipulation, in lab-on-a-chip devices. Bacteria swim using a bundle of flagella (flexible hair-like structures) that form a rotating cork-screw of chiral shape. To mimic bacterial swimming, we employ a computational approach to design a bacterial (chirality-induced) swimmer whose chiral shape and rotational velocity can be controlled by an external magnetic field. In our model, we numerically solve the coupled governing equations that describe the system dynamics (i.e. solid mechanics, fluid dynamics and magnetostatics). We explore the swimming response as a function of the characteristic dimensionless parameters and put special emphasis on controlling the swimming direction. Our results provide fundamental physical insight on the chirality-induced propulsion, and it provides guidelines for the design of magnetic bi-directional micro-swimmers. © 2013 The Author(s) Published by the Royal Society. All rights reserved.

The use of non-dimensional parameters to study stress in lithiumion battery electrode storage particles

Mechanical degradation is thought to be one of the causes of capacity fade within Lithium-Ion batteries. In this work we develop a coupled stress-diffusion model for idealized spherical storage particles, which is analogous to the development of thermal strains. We then non-dimensionalize the model and identify three important parameters that control the development of stress within these particles. We can therefore use a wide number of values for these parameters to make predictions about the stress responses of different materials. The maximum stress developed within the particle for different values of these parameters are plotted as stress maps. A two dimensional model of a battery was then developed, in order to study the effect of particle morphology. Copyright © 2012 by ASME.

An integrated 2-D model of a lithium ion battery: The effect of material parameters and morphology on storage particle stress

An integrated 2-D model of a lithium ion battery is developed to study the mechanical stress in storage particles as a function of material properties. A previously developed coupled stress-diffusion model for storage particles is implemented in 2-D and integrated into a complete battery system. The effect of morphology on the stress and lithium concentration is studied for the case of extraction of lithium in terms of previously developed non-dimensional parameters. These non-dimensional parameters include the material properties of the storage particles in the system, among other variables. We examine particles functioning in isolation as well as in closely-packed systems. Our results show that the particle distance from the separator, in combination with the material properties of the particle, is critical in predicting the stress generated within the particle. © 2012 Springer-Verlag.