Highly flexible all-optical wavelength conversion at 2.488 Gbits/s using a multi-output-wavelength laser

An integrated multiwavelength grating cavity (MGC) laser fabricated by selective area regrowth is demonstrated. In addition to allowing wavelength conversion, the device can perform various important network functions such as space switching and multiplexing. The use of the device for these functions offers several advantages from a wavelength division multiplexing (WDM) network, such as flexibility, reduced component count, size, and the associated cost reduction.

Engineering development of the Lancaster flexible bag.

Describes progress in the last 12 months which has established bag designs and fabrication techniques, giving greater confidence in the life and cost of these components. A quarter scale bag is under construction. Extensive tank testing has also established life time bending moment and mooring load envelopes, enabling hull and mooring design to proceed. A computer simulation programme has been used to check tank model results and to establish turbine and generator operating conditions. This has allowed generation and transmission component design to proceed, and suggests a high operating efficiency can be maintained with a simple control regime. Simple solutions in minor areas such as valve design and damage stability control add to the picture of steady progress in establishing the Lancaster Flexible Bag 's feasibility.

The influence of peel angle on the mechanics of peeling flexible adherends with arbitrary load-extension characteristics

The peel test is commonly used to determine the strength of adhesive joints. In its simplest form, a thin flexible strip which has been bonded to a rigid surface is peeled from the substrate at a constant rate and the peeling force which is applied to the debonding surfaces by the tension in the tape is measured. Peeling can be carried out with the peel angle, i.e. the angle made by the peel force with the substrate surface, from any value above about 10° although peeling tests at 90 and 180° are most common. If the tape is sufficiently thin for its bending resistance to be negligibly small then as well as the debonding or decohesion energy associated with the adhesive in and around the point of separation, the relation between the peeling force and the peeling angle is influenced both by the mechanical properties of the tape and any pre-strain locked into the tape during its application to the substrate. The analytic solution for a tape material which can be idealised as elastic perfectly-plastic is well established. Here, we present a more general form of analysis, applicable in principle to any constitutive relation between tape load and tape extension. Non-linearity between load and extension is of increasing significance as the peel angle is decreased: the model presented is consistent with existing equations describing the failure of a lap joint between non-linear materials. The analysis also allows for energy losses within the adhesive layer which themselves may be influenced by both peel rate and peel angle. We have experimentally examined the application of this new analysis to several specific peeling cases including tapes of cellophane, poly-vinyl chloride and PTFE. © 2005 Elsevier Ltd. All rights reserved.

Flexible array sensors based on zinc oxide nanowires for touch displays

Recent efforts towards the fabrication of touch sensing systems are presented, in which zinc oxide nanowire arrays are embedded in a polymer matrix to produce an engineered composite material. In the future, these sensor systems will be fully flexible and multi-touch as intended for Nokia's 'Morph' concept device.

Hydrodynamic pressures behind flexible and rigid dams

During earthquakes, hydrodynamic pressures are generated by the impounded reservoir on the dam face. The magnitude and distribution of the hydrodynamic pressures vary with factors such as frequency and intensity of earthquake-induced ground motion, depth of impounded reservoir, stiffness of dam and geological conditions. It is difficult to obtain experimental data on hydrodynamic pressures from the field owing to uncertainties associated with earthquake loading. This paper aims at using dynamic centrifuge modelling to measure hydrodynamic pressures behind both relatively stiff and flexible model dams. Comparisons of the experimental data with theoretical hydrodynamic pressures show that Westergaard's equation gives a conservative estimation of hydrodynamic pressures. Comparison with Chopra's method revealed that it underpredicts hydrodynamic pressures for low reservoir depths but gives reasonably good predictions for higher depths of reservoir. It is concluded that dynamic centrifuge modelling may be an effective experimental method to estimate the hydrodynamic pressures acting on a dam. © 2010 Thomas Telford Ltd.

Building flexible user interfaces for solving PDEs

FEniCS is a collection of software tools for the automated solution of differential equations by finite element methods. In this note, we describe how FEniCS can be used to solve a simple nonlinear model problem with varying levels of automation. At one extreme, FEniCS provides tools for the fully automated and adaptive solution of nonlinear partial differential equations. At the other extreme, FEniCS provides a range of tools that allow the computational scientist to experiment with novel solution algorithms. © 2010 American Institute of Physics.

Flexible asymmetric spinning

Metal spinning is used to form shell components, but is constrained by two features: it can only produce axisymmetric shapes; it requires a dedicated mandrel for each product. Examination of pressures between product and mandrel revealed that contact is limited to three well defined areas. This suggested that the full mandrel could be replaced by three rollers. Furthermore, if these rollers could be controlled, they could represent any symmetric or asymmetric mandrel. A seven-axis machine has been designed, manufactured, and used to spin trial parts. The machine design is described, and preliminary results give an indicator of process capability. © 2011 CIRP.