Test on prestressed concrete beam with AFRP spiral confinement and external aramid tendons

This paper describes an experimental study of a new form of prestressed concrete beam. Aramid Fiber Reinforced Polymers (AFRPs) are used to provide compression confinement in the form of interlocking circular spirals, while external tendons are made from parallel-lay aramid ropes. The response shows that the confinement of the compression flange significantly increases the ductility of the beam, allowing much better utilization of the fiber strength. The failure of the beam is characterized by rupture of spiral confinement reinforcement.

Estimating and Enhancing the Yield of Tuneling SRAM Cells by Simulation

As a novel implementation of the static random access memory (SRAM), the tunneling SRAM (TSRAM) uses the negative differential resistance of tunnel diodes (TD’s) and potentially offers considerable improvements in both standby power dissipation and integration density compared to the conventional CMOS SRAM. TSRAM has not yet been realized with a useful bit capacity mainly because the level of uniformity required of the nanoscale TD’s has been demanding and difficult to achieve. In this letter, we propose a Monte Carlo approach for estimating the yield of TSRAM cells and show that by optimizing the cell’s external circuit parameters, we can relax the allowable tolerance of a key device parameter of a resonant-TD-(RTD) based cell by three times.

External corporate venture capital investment: Towards a framework for capturing and measuring strategic value

This paper presents the initial results of on-going research in the field of external Corporate Venture Capital (CVC) investments, i.e. equity investments of large corporations in entrepreneurial ventures which originated outside the corporation. The research is motivated by the fact that external CVC plays an increasingly important role within the strategy of corporations. Driven by a general trend towards a more open approach to innovation, companies see particular value in external corporate venturing as a tool to gain, for example, access to complementary technologies and a general window on technology developments. The review of literature in the field of external corporate venturing clearly reveals that theoretical gaps exist in understanding mechanisms for capturing value and measurements of this value. To help close these gaps, the research addresses the underlying question "How do corporations and start-ups capture and measure strategic value through external CVC investments" by using embedded, multiple case studies. Following an initial set of case studies, steps towards the development of a framework for capturing and measuring strategic value from CVC investments are outlined within this paper and the resulting preliminary framework is presented. The paper closes with an outlook on ongoing and future research steps. © 2009 PICMET.

Parameters influencing the performance of an IGBT gate drive

This paper presents an improvement of an IGBT gate drive implementing Active Voltage Control (AVC), and investigates the impact of various parameters affecting its performance. The effects of the bandwidths of various elements and the gains of AVC are shown in simulation and experimentally. Also, the paper proposes connecting a small Active Snubber between the IGBT collector and its gate integrated within the AVC. The effect of this snubber on enhancing the stability of the gate drive is demonstrated. It will be shown that using a wide bandwidth operational amplifier and integrating the Active Snubber within the gate drive reduces the minimum gate resistor required to achieve stability of the controller. Consequently, the response time of the IGBT to control signals is significantly reduced, the switching losses then can be minimised and, hence, the performance of gate drive as whole is improved. This reflects positively on turn-off and turn-on transitions achieving voltage sharing between the IGBTs connected in series to construct a higher voltage switch, making series IGBTs a feasible practice. ©2008 IEEE.

Parameters identification by a single point free response measurement

When a thin rectangular plate is restrained on the two long edges and free on the remaining edges, the equivalent stiffness of the restraining joints can be identified by the order of the natural frequencies obtained using the free response of the plate at a single location. This work presents a method to identify the equivalent stiffness of the restraining joints, being represented as simply supporting the plate but elastically restraining it in rotation. An integral transform is used to map the autospectrum of the free response from the frequency domain to the stiffness domain in order to identify the equivalent torsional stiffness of the restrained edges of the plate and also the order of natural frequencies. The kernel of the integral transform is built interpolating data from a finite element model of the plate. The method introduced in this paper can also be applied to plates or shells with different shapes and boundary conditions. © 2011 Elsevier Ltd. All rights reserved.

I did that! Measuring users' experience of agency in their own actions

Cognitive neuroscience defines the sense of agency as the experience of controlling one's own actions and, through this control, affecting the external world. We believe that the sense of personal agency is a key factor in how people experience interactions with technology. This paper draws on theoretical perspectives in cognitive neuroscience and describes two implicit methods through which personal agency can be empirically investigated. We report two experiments applying these methods to HCI problems. One shows that a new input modality - skin-based interaction - can substantially increase users' sense of agency. The second demonstrates that variations in the parameters of assistance techniques such as predictive mouse acceleration can have a significant impact on users' sense of agency. The methods presented provide designers with new ways of evaluating and refining empowering interaction techniques and interfaces, in which users experience an instinctive sense of control and ownership over their actions. Copyright 2012 ACM.

Auto-calibration of a camera system using Image Alignment

Calibration of a camera system is a necessary step in any stereo metric process. It correlates all cameras to a common coordinate system by measuring the intrinsic and extrinsic parameters of each camera. Currently, manual calibration of a camera system is the only way to achieve calibration in civil engineering operations that require stereo metric processes (photogrammetry, videogrammetry, vision based asset tracking, etc). This type of calibration however is time-consuming and labor-intensive. Furthermore, in civil engineering operations, camera systems are exposed to open, busy sites. In these conditions, the position of presumably stationary cameras can easily be changed due to external factors such as wind, vibrations or due to an unintentional push/touch from personnel on site. In such cases manual calibration must be repeated. In order to address this issue, several self-calibration algorithms have been proposed. These algorithms use Projective Geometry, Absolute Conic and Kruppa Equations and variations of these to produce processes that achieve calibration. However, most of these methods do not consider all constraints of a camera system such as camera intrinsic constraints, scene constraints, camera motion or varying camera intrinsic properties. This paper presents a novel method that takes all constraints into consideration to auto-calibrate cameras using an image alignment algorithm originally meant for vision based tracking. In this method, image frames are taken from cameras. These frames are used to calculate the fundamental matrix that gives epipolar constraints. Intrinsic and extrinsic properties of cameras are acquired from this calculation. Test results are presented in this paper with recommendations for further improvement.

Influence of film cooling hole angles and geometries on aerodynamic loss and net heat flux reduction

Turbine design engineers have to ensure that film cooling can provide sufficient protection to turbine blades from the hot mainstream gas, while keeping the losses low. Film cooling hole design parameters include inclination angle (α), compound angle (β ), hole inlet geometry and hole exit geometry. The influence of these parameters on aerodynamic loss and net heat flux reduction is investigated, with loss being the primary focus. Low-speed flat plate experiments have been conducted at momentum flux ratios of IR = 0.16, 0.64 and 1.44. The film cooling aerodynamic mixing loss, generated by the mixing of mainstream and coolant, can be quantified using a three-dimensional analytical model that has been previously reported by the authors. The model suggests that for the same flow conditions, the aerodynamic mixing loss is the same for holes with different α and β but with the same angle between the mainstream and coolant flow directions (angle κ). This relationship is assessed through experiments by testing two sets of cylindrical holes with different α and β : one set with κ = 35°, another set with κ = 60°. The data confirm the stated relationship between α, β, κ and the aerodynamic mixing loss. The results show that the designer should minimise κ to obtain the lowest loss, but maximise β to achieve the best heat transfer performance. A suggestion on improving the loss model is also given. Five different hole geometries (α =35.0°, β =0°) were also tested: cylindrical hole, trenched hole, fan-shaped hole, D-Fan and SD-Fan. The D-Fan and the SD-Fan have similar hole exits to the fan-shaped hole but their hole inlets are laterally expanded. The external mixing loss and the loss generated inside the hole are compared. It was found that the D-Fan and the SD-Fan have the lowest loss. This is attributed to their laterally expanded hole inlets, which lead to significant reduction in the loss generated inside the holes. As a result, the loss of these geometries is ≈ 50 % of the loss of the fan-shaped hole at IR = 0.64 and 1.44. Copyright © 2011 by ASME.

The energy required to produce materials: constraints on energy-intensity improvements, parameters of demand.

In this paper, we review the energy requirements to make materials on a global scale by focusing on the five construction materials that dominate energy used in material production: steel, cement, paper, plastics and aluminium. We then estimate the possibility of reducing absolute material production energy by half, while doubling production from the present to 2050. The goal therefore is a 75 per cent reduction in energy intensity. Four technology-based strategies are investigated, regardless of cost: (i) widespread application of best available technology (BAT), (ii) BAT to cutting-edge technologies, (iii) aggressive recycling and finally, and (iv) significant improvements in recycling technologies. Taken together, these aggressive strategies could produce impressive gains, of the order of a 50-56 per cent reduction in energy intensity, but this is still short of our goal of a 75 per cent reduction. Ultimately, we face fundamental thermodynamic as well as practical constraints on our ability to improve the energy intensity of material production. A strategy to reduce demand by providing material services with less material (called 'material efficiency') is outlined as an approach to solving this dilemma.

The effects of operational and design parameters on the tolerance of ADSR fuel pin cladding to beam interruptions

This paper investigates the effects of design parameters, such as cladding and coolant material choices, and operational phenomena, such as creep and fission product decay heat, on the tolerance of Accelerator Driven Subcritical Reactor (ADSR) fuel pin cladding to beam interruptions. This work aims to provide a greater understanding of the integration between accelerator and nuclear reactor technologies in ADSRs. The results show that an upper limit on cladding operating temperature of 550 °C is appropriate, as higher values of temperature tend to accelerate creep, leading to cladding failure much sooner than anticipated. The effect of fission product decay heat is to reduce significantly the maximum stress developed in the cladding during a beam-trip-induced transient. The potential impact of irradiation damage and the effects of the liquid metal coolant environment on the cladding are discussed. © 2013 Elsevier Ltd. All rights reserved.