Dead-time minimisation using active voltage control gate drive for high-power IGBT converters

High-power converters usually need longer dead-times than their lower-power counterparts and a lower switching frequency. Also due to the complicated assembly layout and severe variations in parasitics, in practice the conventional dead-time specific adjustment or compensation for high-power converters is less effective, and usually this process is time-consuming and bespoke. For general applications, minimising or eliminating dead-time in the gate drive technology is a desirable solution. With the growing acceptance of power electronics building blocks (PEBB) and intelligent power modules (IPM), gate drives with intelligent functions are in demand. Smart functions including dead time elimination/minimisation can improve modularity, flexibility and reliability. In this paper, a dead-time minimisation using Active Voltage Control (AVC) gate drive is presented. © 2012 IEEE.

Control and operation of a high temperature superconducting synchronous motor

We have built a four-pole high temperature superconducting (HTS) permanent magnet synchronous motor (PMSM) in our lab. At this stage, the HTS PMSM uses two 2G HTS racetrack coils, which are YBCO wires, type 344 from AMSC, and four conventional copper coils as stator windings. 75 YBCO bulks are mounted on the surface of the rotor. After the pulsed field magnetization system had been developed and tested in our lab in 2011, the rotor can trap a four-pole magnetic field. This makes HTS bulks possible for motor application, other than HTS coils. The HTS PMSM can successfully run at a low speed of around 150 rpm for an initial test. This paper states theoretical and practical works on the HTS PMSM's operation including HTS motor drive development and its application. © 2002-2011 IEEE.

IGBT converters conducted EMI analysis by controlled multiple-slope switching waveform approximation

IGBTs realise high-performance power converters. Unfortunately, with fast switching of the IGBT-free wheel diode chopper cell, such circuits are intrinsic sources of high-level EMI. Therefore, costly EMI filters or shielding are normally needed on the load and supply side. In order to design these EMI suppression components, designers need to predict the EMI level with reasonable accuracy for a given structure and operating mode. Simplifying the transient IGBT switching current and voltage into a multiple slope switching waveform approximation offers a feasible way to estimate conducted EMI with some accuracy. This method is dependent on the availability of high-fidelity measurements. Also, that multiple slope approximation needs careful and time-costly IGBT parameters optimisation process to approach the real switching waveform. In this paper, Active Voltage Control Gate Drive(AVC GD) is employed to shape IGBT switching into several defined slopes. As a result, Conducted EMI prediction by multiple slope switching approximation could be more accurate, less costly but more friendly for implementation. © 2013 IEEE.

Effects of longer heavy vehicles on traffic congestion

Two-lane, "microscopic" (vehicle-by-vehicle) simulations of motorway traffic are developed using existing models and validated using measured data from the M25 motorway. An energy consumption model is also built in, which takes the logged trajectories of simulated vehicles as drive-cycles. The simulations are used to investigate the effects on motorway congestion and fuel consumption if "longer and/or heavier vehicles" (LHVs) were to be permitted in the UK. Baseline scenarios are simulated with traffic composed of cars, light goods vehicles and standard heavy goods vehicles (HGVs). A proportion of conventional articulated HGVs is then replaced by a smaller number of LHVs carrying the same total payload mass and volume. Four LHV configurations are investigated: an 18.75 m, 46 t longer semi-trailer (LST); 25.25 m, 50 t and 60 t B-doubles and a 34 m, 82 t A-double. Metrics for congestion, freight fleet energy consumption and car energy consumption are defined for comparing the scenarios. Finally, variation of take-up level and LHV engine power for the LST and A-double are investigated. It is concluded that: (a) LHVs should reduce congestion particularly in dense traffic, however, a low mean proportion of freight traffic on UK roads and low take-up levels will limit this effect to be almost negligible; (b) LHVs can significantly improve the energy efficiency of freight fleets, giving up to a 23% reduction in fleet energy consumption at high take-up levels; (c) the small reduction in congestion caused by LHVs could improve the fuel consumption of other road users by up to 3% in dense traffic, however in free-flowing traffic an opposite effect occurs due to higher vehicle speeds and aerodynamic losses; and (d) underpowered LHVs have potential to generate severe congestion, however current manufacturers' recommendations appear suitable. © 2013 IMechE.