Experimental demonstration of real-time optical OFDM Transmission at 7.5 Gb/s over 25-km SSMF using a 1-GHz RSOA

The 7.5-Gb/s real-time end-to-end optical orthogonal frequency-division- multiplexing (OOFDM) transceivers incorporating variable power loading on each individual subcarrier are demonstrated experimentally using a live-optimized reflective semiconductor optical amplifier intensity modulator having a modulation bandwidth as narrow as 1 GHz. Real-time OOFDM signal transmission at 7.5 Gb/s over 25-km standard single-mode fiber is achieved across the $C$-band in simple intensity modulation and direct detection systems without in-line optical amplification and dispersion compensation. © 2006 IEEE.

Theoretical model for dicke superradiance in a semiconductor laser device

A theoretical model for Dicke superradiance (SR) in diode lasers is proposed using the travelling wave method with a spatially resolved absorber and spectrally resolved gain. The role of electrode configuration and optical bandwidth are compared and contrasted as a route to enhance femtosecond pulse power. While pulse duration can be significantly reduced through careful absorber length specification, stability is degraded. However an increased spectral gain bandwidth of up to 150 nm is predicted to allow pulsewidth reductions of down to 10 fs and over 500-W peak power without further degradation in pulse stability. © 2011 IEEE.

Orthogonal multipulse modulation for next-generation datacommunication links

Orthogonal multipulse modulation is demonstrated to allow ≈30 Gb/s real-time transmission over multimode fibre using an 850 nm VCSEL. The scheme eases considerably component bandwidth requirements compared with conventional NRZ modulation. © 2011 OSA.

Parameters influencing the performance of an IGBT gate drive

This paper presents an improvement of an IGBT gate drive implementing Active Voltage Control (AVC), and investigates the impact of various parameters affecting its performance. The effects of the bandwidths of various elements and the gains of AVC are shown in simulation and experimentally. Also, the paper proposes connecting a small Active Snubber between the IGBT collector and its gate integrated within the AVC. The effect of this snubber on enhancing the stability of the gate drive is demonstrated. It will be shown that using a wide bandwidth operational amplifier and integrating the Active Snubber within the gate drive reduces the minimum gate resistor required to achieve stability of the controller. Consequently, the response time of the IGBT to control signals is significantly reduced, the switching losses then can be minimised and, hence, the performance of gate drive as whole is improved. This reflects positively on turn-off and turn-on transitions achieving voltage sharing between the IGBTs connected in series to construct a higher voltage switch, making series IGBTs a feasible practice. ©2008 IEEE.

On bandlimited fading channels at high SNR

This paper provides an overview of results on the capacity of noncoherent, multiple-input multiple-output (MIMO) flat-fading channels with a bandlimited power spectral density. The focus is on results that concern the capacity at high signal-to-noise ratio (SNR). In particular, the capacity pre-log, defined as the limiting ratio of the capacity to the logarithm of the SNR as the SNR tends to infinity, is studied. It is observed that the capacity pre-log is a function of the number of antennas as well as of the bandwidth of the fading channel's power spectral density. It is further observed that the capacity pre-log can be achieved with a simple communication system where the data detection and the channel estimation are performed separately. © 2011 ACM.

Characterization of multimode fiber by selective mode excitation

Each mode of a 2 km 50 μ OM2 grade multimode fiber is precisely excited at multiple orientations using a binary phase spatial light modulator (SLM) to generate a detailed modal description of the fiber and minimize modal dispersion over 4.5 THz of optical bandwidth. © 2012 IEEE.

Cost-effective 10 Gb/s polymer-based chip-to-chip optical interconnect

Board-level optical links are an attractive alternative to their electrical counterparts as they provide higher bandwidth and lower power consumption at high data rates. However, on-board optical technology has to be cost-effective to be commercially deployed. This study presents a chip-to-chip optical interconnect formed on an optoelectronic printed circuit board that uses a simple optical coupling scheme, cost-effective materials and is compatible with well-established manufacturing processes common to the electronics industry. Details of the link architecture, modelling studies of the link's frequency response, characterisation of optical coupling efficiencies and dynamic performance studies of this proof-of-concept chip-to-chip optical interconnect are reported. The fully assembled link exhibits a -3 dBe bandwidth of 9 GHz and -3 dBo tolerances to transverse component misalignments of ±25 and ±37 μm at the input and output waveguide interfaces, respectively. The link has a total insertion loss of 6 dBo and achieves error-free transmission at a 10 Gb/s data rate with a power margin of 11.6 dBo for a bit-error-rate of 10 -12. The proposed architecture demonstrates an integration approach for high-speed board-level chip-to-chip optical links that emphasises component simplicity and manufacturability crucial to the migration of such technology into real-world commercial systems. © 2012 The Institution of Engineering and Technology.

Long Distance Wireless Networking for Site - Office Data Communications

Effective data communications between the project site and decision making office can be critical for the success of a construction project. It allows convenient access to centrally stored information and allows centrally located decision makers to remotely monitor the site and collect data in real-time. However, high bandwidth, flexible data communication networks, such as wired local area networks, can often be time-consuming and costly to deploy for such purposes especially when project sites (dams, highways, etc.) are located in rural, undeveloped areas where networking infrastructure is not available. In such construction sites, wireless networking could reliably link the construction site and the decision-making office. This paper presents a case study on long-distance, site – office wireless data communications. The purpose was to investigate the capability of wireless technology in exchanging construction data in a fast and efficient manner and in allowing site personnel to interact and share knowledge and data with the office staff. This study took place at the University of Michigan’s campus where performance, reliability, and cost/benefit tests were performed. The indoor and outdoor tests performed demonstrated the suitability of this technology for office-site data communications and exposed the need for more research to further improve the reliability and data handling of this technology.

Mode division multiplexing over 2km of OM2 fibre using rotationally optimized mode excitation with fibre coupler demultiplexer

A Spatial Light Modulator and a non-specialized multimode coupler are used together to provide sufficient channel isolation and modal bandwidth for 2x12.5Gbps NRZ over 2km of standard graded-index multimode fibre without DSP. © 2012 IEEE.

Sensor data scheduling for linear quadratic Gaussian control with full state feedback

Networked control systems (NCSs) have attracted much attention in the past decade due to their many advantages and growing number of applications. Different than classic control systems, resources in NCSs, such as network bandwidth and communication energy, are often limited, which degrade the closed-loop system performance and may even cause the system to become unstable. Seeking a desired trade-off between the closed-loop system performance and the limited resources is thus one heated area of research. In this paper, we analyze the trade-off between the sensor-to-controller communication rate and the closed-loop system performance indexed by the conventional LQG control cost. We present and compare several sensor data schedules, and demonstrate that two event-based sensor data schedules provide better trade-off than an optimal offline schedule. Simulation examples are provided to illustrate the theories developed in the paper. © 2012 AACC American Automatic Control Council).

Design of a compact reconfigurable optical interconnection using nematic liquid crystal spatial light modulator

The wavelength-division multiplexing (WDM) has been proposed as a promising technology to efficiently use the available bandwidth of a single optical fibre. This can be achieved by transmitting different channels on the optical fibre with each channel modulating a different wavelength. The aim of this paper is to propose a compact design (35 mm×65 mm) of a reconfigurable holographic optical switch in order to access and manipulate 4 channels at a node of a fibre-optic communication network. A vital component of such a switch is a nematic liquid crystal spatial light modulator offering control and flexibility at the channel manipulation stage and providing the ability to redirect light into the desired output fibre. This is achieved by the use of a 2-D analogue phase computer generated hologram (CGH) based on liquid crystal on silicon (LCOS) technology. © 2012 SPIE.

Control and operation of a high temperature superconducting synchronous motor

We have built a four-pole high temperature superconducting (HTS) permanent magnet synchronous motor (PMSM) in our lab. At this stage, the HTS PMSM uses two 2G HTS racetrack coils, which are YBCO wires, type 344 from AMSC, and four conventional copper coils as stator windings. 75 YBCO bulks are mounted on the surface of the rotor. After the pulsed field magnetization system had been developed and tested in our lab in 2011, the rotor can trap a four-pole magnetic field. This makes HTS bulks possible for motor application, other than HTS coils. The HTS PMSM can successfully run at a low speed of around 150 rpm for an initial test. This paper states theoretical and practical works on the HTS PMSM's operation including HTS motor drive development and its application. © 2002-2011 IEEE.

Holographic beam steering a directly modulated twoelectrode high brightness tapered laser diode for optical wireless communications

An error-free free space communication link with 3 angular coverage and 1.25GHz modulation bandwidth is demonstrated by beam steering an ultra high modulation efficiency bright tapered laser diode using a Liquid Crystal Spatial Light Modulator. © OSA 2012.

Free space communications with beam steering a two-electrode tapered laser diode using liquid-crystal slm

A free space optical wireless communication system with 3 degree angular coverage and 1.25 GHz modulation bandwidth is reported, in which relatively narrow laser beam of a simultaneous high power, high modulation speed and ultra high modulation efficiency directly modulated two-electrode tapered laser diode is steered using a nematic phase-only Liquid-Crystal On Silicon Spatial Light Modulator (LCOS SLM) by displaying reconfigurable 256 phase level gratings. © 1983-2012 IEEE.

A power optimised narrowband power-line communication system

Narrowband Power-line Communication (NPLC) technology uses a narrow bandwidth to transmit information. Its major applications include control, smart home systems and security. This paper proposes a power optimised NPLC system to minimise its systemic power consumption without compromising its communication ability. By using the proposed Smart Energy Conservation Layer which reads the signal strength from the PLC channel, a power optimised system is achieved to provide the essential transmitting power to secure the communications. Compared to commercial systems, the potential power saving could be up to 99% in a household environment, as demonstrated by the experimental results. © 2013 IEEE.