Contrasting code performances for computational aeroacoustics of jets

The numerical propagation of subcritical Tollmein-Schlichting (T-S), inviscid vortical and cut-on acoustic waves is explored. For the former case, the performances of the very different NEAT, NTS, HYDRA, FLUXp and OSMIS3D codes is studied. A modest/coarse hexahedral computational grid that starkly shows differences between the different codes and schemes used in them is employed. For the same order of discretization the five codes show similar results. The unstructured codes are found to propagate vortical and acoustic waves well on triangular cell meshes but not the T-S wave. The above code contrasting exercise is then carried out using implicit LES or Smagorinsky LES for and Ma = 0.9 plane jet on modest 0.5 million cell grids moving to circa 5 million cell grids. For this case, even on the coarse grid, for all codes results were generally encouraging. In general, the spread in computational results is less than the spread of the measurements. Interestingly, the finer grid turbulence intensity levels are slightly more under-predicted than those of the coarse grid. This difference is attributed to the numerical dispersion error having a favourable coarse grid influence. For a non-isothermal jet, HYDRA and NTS also give encouraging results. Peak turbulence values along the jet centreline are in better agreement with measurements than for the isothermal jets. Copyright © 2006 by University of Wales.

The performance of ejectors driven by sinusoidally unsteady jets

The operation of ejectors driven by a low-speed, sinusoidally unsteady jet has been studied. The thrust augmentation is shown to be highly dependent on the non-dimensional frequency of the driver jet, but independent of its Mach Number. Convective rather than acoustically propagated phenomena dominate the ejector flowfield. Unsteady pressure measurements on the internal surfaces of the ejector have enabled convecting ring vortices to be identified. The impingement of a ring vortex on the leading edge of the ejector causes the peak unsteady body force. The non-dimensional diameter of the ejector is shown to be the only geometric variable that affects the optimum non-dimensional frequency for thrust augmentation. An experimentally optimised geometry is presented. An expression relating the mechanical efficiency and thrust augmentation of the ejector is developed, and shown to be crucially dependent on the degree of unsteadiness in the ejector exit plane.

Hybrid LES - RANS of complex geometry jets

Large eddy simulation (LES) type studies are made of a realistic geometry coaxial nozzle with a pylon. For the LES, since the solver being used tends towards having dissipative qualities, the subgrid scale (SGS) model is omitted, giving Numerical LES (NLES). To overcome near wall streak resolution problems a near wall RANS (Reynolds averaged Navier Stokes) model is used giving a hybrid NLES-RANS approach.The pylon is shown to influence the flow development, having a significant impact on peak turbulence levels and spreading rates. The results show that real geometry effects are influential and should be taken into account when moving towards real engine simulations. If their effects are ignored then, based on the studies here, key turbulence parameters will have significant error.

Surface tension-induced global instability of planar jets and wakes

The effect of surface tension on global stability of co-flow jets and wakes at a moderate Reynolds number is studied. The linear temporal two-dimensional global modes are computed without approximations. All but one of the flow cases under study are globally stable without surface tension. It is found that surface tension can cause the flow to be globally unstable if the inlet shear (or equivalently, the inlet velocity ratio) is strong enough. For even stronger surface tension, the flow is re-stabilized. As long as there is no change of the most unstable mode, increasing surface tension decreases the oscillation frequency. Short waves appear in the high-shear region close to the nozzle, and their wavelength increases with increasing surface tension. The critical shear (the weakest inlet shear at which a global instability is found) gives rise to antisymmetric disturbances for the wakes and symmetric disturbances for the jets. However, at stronger shear, the opposite symmetry can be the most unstable one, in particular for wakes at high surface tension. The results show strong effects of surface tension that should be possible to reproduce experimentally as well as numerically.

Dynamic behaviour of gas jets in laser cutting

The efficiency and overall quality of a laser cutting operation is highly dependent on the assist gas parameters. The desire to cut thicker material has led to the observation of small process operating windows for thicker sections. The gas jet delivery and subsequent dynamical behaviour have significant effects on the cutting operation as the sample thickness increases. To date, few workers have examined the dynamical behaviour of the gas jet. This paper examines the characteristics of oxygen gas jets during CO2 laser cutting of steel. Particular emphasis is placed on the mass transfer effects that are operating within the kerf. Oxygen concentration levels within a model kerf are measured for various laser cutting set-ups. The results show a substantial reduction in oxygen concentration within the kerf. A system for oxygen concentration maintenance is described and cutting results from this system are compared with conventional techniques for cutting steels in the range 10 to 20mm thick. A theoretical analysis of turbulent mass transfer within a kerf is presented and compared with experiment.

Thermal stratification produced by plumes and jets in enclosed spaces

The airflow and thermal stratification produced by a localised heat source located at floor level in a closed room is of considerable practical interest and is commonly referred to as a 'filling box'. In rooms with low aspect ratios H/R ≲ 1 (room height H to characteristic horizontal dimension R) the thermal plume spreads laterally on reaching the ceiling and a descending horizontal 'front' forms separating a stably stratified, warm upper region from cooler air below. The stratification is well predicted for H/R ≲ 1 by the original filling box model of Baines and Turner (J. Fluid. Mech. 37 (1968) 51). This model represents a somewhat idealised situation of a plume rising from a point source of buoyancy alone-in particular the momentum flux at the source is zero. In practical situations, real sources of heating and cooling in a ventilation system often include initial fluxes of both buoyancy and momentum, e.g. where a heating system vents warm air into a space. This paper describes laboratory experiments to determine the dependence of the 'front' formation and stratification on the source momentum and buoyancy fluxes of a single source, and on the location and relative strengths of two sources from which momentum and buoyancy fluxes were supplied separately. For a single source with a non-zero input of momentum, the rate of descent of the front is more rapid than for the case of zero source momentum flux and increases with increasing momentum input. Increasing the source momentum flux effectively increases the height of the enclosure, and leads to enhanced overturning motions and finally to complete mixing for highly momentum-driven flows. Stratified flows may be maintained by reducing the aspect ratio of the enclosure. At these low aspect ratios different long-time behaviour is observed depending on the nature of the heat input. A constant heat flux always produces a stratified interior at large times. On the other hand, a constant temperature supply ultimately produces a well-mixed space at the supply temperature. For separate sources of momentum and buoyancy, the developing stratification is shown to be strongly dependent on the separation of the sources and their relative strengths. Even at small separation distances the stratification initially exhibits horizontal inhomogeneity with localised regions of warm fluid (from the buoyancy source) and cool fluid. This inhomogeneity is less pronounced as the strength of one source is increased relative to the other. Regardless of the strengths of the sources, a constant buoyancy flux source dominates after sufficiently large times, although the strength of the momentum source determines whether the enclosure is initially well mixed (strong momentum source) or stably stratified (weak momentum source). © 2001 Elsevier Science Ltd. All rights reserved.