Experimental analysis of SCM-based transmission over 500 m of FDDI-grade multimode fiber with enhancement from electronic equalization

Experimental analysis is applied for the first time to identify optimal launch conditions and carrier frequencies for SCM transmission over worst-case MMF. Potential for performance enhancement using electronic equalization is demonstrated for the first time. © 2006 Optical Society of America.

Ultrafast all-optical wavelength conversion using an integrated amplifier/DFB laser

Wavelength conversion in the 1550 nm regime was achieved in an integrated semiconductor optical amplifier (SOA)/DFB laser by modulating the output power of the laser with a light beam of a different wavelength externally injected into the SOA section. A 12 dB output extinction ratio was obtained for an average coupled input power of 75 μW with the laser section driven at 65 mA and the amplifier section at 180 mA. The response time achieved was as low as 13 ps with the laser biased at 175 mA even with low extinction ratios. The laser exhibits a similar recovery time allowing potentially very high bit-rate operation.

Demonstration of 2.488Gb/s simultaneous all-optical wavelength conversion and tone reading/replacing in an integrated-SOA/DFB laser

A technique is demonstrated that allows for the wavelength conversion of data with both simultaneous monitoring and replacing of a wavelength identifying pilot tone. The technique should be upgradable to data rates of 10Gb/s and higher.

Mode-controlled vertical cavity surface emitting lasers for bandwidth enhancement of multimode fibre links

A GaAs Vertical Cavity Surface Emitting Laser (VCSEL) that generates controlled modes offset from the center is described. The device is modulated with a 27-1 pseudo-random bit sequence and its output is transmitted along a 1 km length of multimode fiber (MMF). Open eyes are obtained for data rates as high as 1.4Gb/s. The transmission bandwidth increases by a factor of 4 over over-filled launch (OFL). This enhancement is stable against environment influences on the fiber.

Wavelength conversion, regeneration and tone manipulation using integrated semiconductor lasers and amplifiers

An integrated semiconductor optical amplifier/distributed feedback (SOA/DFB) laser that show promise as a simple all-optical wavelength conversion device together with useful simultaneous functions such as 2R regeneration and the ability to remove a wavelength identifying tone is presented. Wavelength conversion performance at 20Gb/s and 40Gb/s can be obtained with this laser.

All-optical 3R regeneration and format conversion in an integrated SOA/DFB laser

Using a compact, integrated device at 2.488Gb/s, simultaneous NRZ to RZ format conversion and regeneration was achieved. The regenerated signal has a negative BER sensitivity of -1.5dB compared with a data signal transmitted down 101km of standard fiber.

All-optical 3R regeneration and wavelength conversion in an integrated SOA/DFB laser: Experiment and simulation

The simultaneous all optical 3R regeneration and format conversion in a simple, single integrated device was examined. The integrated device consisted of a semiconductor optical fiber (SOA) monolithically integrated with a distributed feedback (DFB) laser. Gain saturation was employed for the transmission of a data signal regenerated all-optically in the laser/amplifier device. The regeneration of the electrically filtered eye diagrams was observed by noise removal and extinction ratio-improvement by the device.

10-Gbit/s transmission over 300-m standard multimode fiber using multilevel coding and 2-channel WDM

A combination of multilevel coding schemes and simple two-channel wavelength division multiplexing (WDM) at 1300 and 1550 nm was used to transmit an aggregate of 10 Gbit/s over 300 m of multimode fiber that is typical of that employed in current Local Area Networks (LANs). It was shown that this technique could be a simple solution for achieving 10 Gigabit ethernet links over installed multimode fiber building backbones.

Subcarrier modulation for transmission of 1-Gbit/s channels over 500 m of 62.5-μm multimode fiber

The use of two different subcarriers at frequencies up to 5.5 GHz each transmitting 1 Gbit/s over 500 m of multimode fiber (MMF) is demonstrated. By transmitting the two subcarrier channels simultaneously alongside the baseband signal, an aggregate bit rate of 2.8 Gbit/s is possible.

Uncooled, 10Gb/s operation of two-contact InGaAsP lasers with low drive current

Uncooled, high-speed modulation of two-contact lasers is presented with ultra-low drive currents. Practical operation at 10Gb/s up to temperatures of 85°C and extinction ratios of 6dB are found for current swings which are less than 40% of conventional lasers.

Waveguide lasers in Er:Yb-doped phosphate glass fabricated by femtosecond laser writing

Advanced waveguide lasers, operating both in continuous wave and pulsed regimes, have been realized in an active phosphate glass by direct writing with femtosecond laser pulses. Stable single mode operation was obtained; the laser provided more than 50 m W in single longitudinal and transverse mode operation with 21% slope efficiency. Furthermore, by combining a high gain waveguide and an innovated fiber-pigtailed saturable absorber based on carbon nanotubes, a mode-locked ring laser providing transform limited 1.6 ps pulses was demonstrated. © 2007 IEEE.

Ultrafast and high-energy pulsed lasers with graphene mode-lockers

The conventional technology for generating ultrashort pulses relies on soliton-like operation based mode-locking. In this regime, the pulse duration is limited by nonlinear optical effects[1]. One method to mitigate these effects is to alternate segments of normal and anomalous group velocity dispersion (GVD) fiber[1]. This configuration is known as dispersion-managed soliton design. It decreases the nonlinear optical effects and reduces the pulse duration[1]. © 2011 IEEE.

Fiber laser processing of amorphous rare earth NeFeB magnetic materials

Since the exchange coupling theory was proposed by Kneller and Hawig in 1991 there has been a significant effort within the magnetic materials community to enhance the performance of rare earth magnets by utilising nano-composite meta-materials. Inclusions of magnetically soft iron smaller than approximately 10 nm in diameter are exchange coupled to a surrounding magnetically hard Nd2Fe14B matrix and provide an enhanced saturisation magnetisation without reducing coercivity. For such a fine nanostructure to be produced, close control over the thermal history of the material is needed. A processing route which provides this is laser annealing from an amorphous alloy precursor. In the current work, relationships between laser parameters, thermal histories of laser processed amorphous stoichiometric NdFeB ribbons and the magnetic properties of the resulting nanocrystalline products have been determined with a view to applying the process to thick film nanocomposite magnet production.