Potential tuning of porous silicon luminescence

Electrochemical investigations were conducted of the effect of potential on the luminescence of porous silico (PS). The use of liquid contacts allows the potential to be controlled during studies of the photoluminescence (PL) and electroluminescence (EI). The PL and EL of PS samples prepared from n-type substrates is considered. To obtain luminescence from such PS it is necessary to generate holes in the valence band. This is achieved by either photoexcitation or an electrochemical process involving the reduction of persulfate. This paper describes the investigations of the effect of potential on the PL and EL of PS. A mechanism of 'potential tuning' based on electron occupancy and Auger quenching is then proposed.

Wake, shock and potential field interactions in a 1.5 stage turbine: Part I: Vane-rotor and rotor-vane interaction

The composition of the time-resolved surface pressure field around a high-pressure rotor blade caused by the presence of neighboring blade rows was studied, with the individual effects of wake, shock and potential field interaction being determined. Two test geometries were considered: first, a high-pressure turbine stage coupled with a swan-necked diffuser exit duct; secondly, the same high-pressure stage but with a vane located in the downstream duct. Both tests were carried out at engine-representative Mach and Reynolds numbers. By comparing the results to time-resolved computational predictions of the flowfield, the accuracy with which the computation predicts blade interaction was determined. It was found that in addition to upstream vane-rotor and rotor-downstream vane interactions, a new interaction mechanism was found resulting from the interaction between the downstream vane's potential field and the upstream vane's trailing edge potential field and shock.

Wake, shock and potential field interactions in a 1.5 stage turbine: Part II: Vane-vane interaction and discussion of results

The composition of the time-resolved surface pressure field around a high-pressure rotor blade caused by the presence of neighboring blade rows was studied, with the individual effects of wake, shock and potential field interaction being determined. Two test geometries were considered: first, a high-pressure turbine stage coupled with a swan-necked diffuser exit duct; secondly, the same high-pressure stage but with a vane located in the downstream duct. Both tests were carried out at engine-representative Mach and Reynolds numbers. By comparing the results to time-resolved computational predictions of the flowfield, the accuracy with which the computation predicts blade interaction was determined. Evidence was obtained that for a large downstream vane, the flow conditions in the rotor passage, at any instant in time, are close to being steady state.

Hybrid potential flow-streamtube method for modelling VAWT-flowfield interactions

When designing vertical-axis wind turbines (VAWTs) for deployment in the urban environment, it is desirable to have a low-cost computational model that allows for modelling the coupled interaction of the turbine with the flowfleld. Such a method is presented in this paper, It combines a variation of the multiple streamtube model with a potential method to model flowfleld interactions. A method referred to as "streamtube surgery" is used to couple the influence of the flowfleld with the performance model of the VAWT. This tool is used to explore the instantaneous and cycle-averaged flowflelds of VAWTs. It can also be used to evaluate the influence on performance of multiple VAWTs in dense arrays or to quantify blockage effects of a VAWT in wind tunnel testing.

Assessing the potential of yield improvements, through process scrap reduction, for energy and CO2 abatement in the steel and aluminium sectors

Targets to cut 2050 CO2 emissions in the steel and aluminium sectors by 50%, whilst demand is expected to double, cannot be met by energy efficiency measures alone, so options that reduce total demand for liquid metal production must also be considered. Such reductions could occur through reduced demand for final goods (for instance by life extension), reduced demand for material use in each product (for instance by lightweight design) or reduced demand for material to make existing products. The last option, improving the yield of manufacturing processes from liquid metal to final product, is attractive in being invisible to the final customer, but has had little attention to date. Accordingly this paper aims to provide an estimate of the potential to make existing products with less liquid metal production. Yield ratios have been measured for five case study products, through a series of detailed factory visits, along each supply chain. The results of these studies, presented on graphs of cumulative energy against yield, demonstrate how the embodied energy in final products may be up to 15 times greater than the energy required to make liquid metal, due to yield losses. A top-down evaluation of the global flows of steel and aluminium showed that 26% of liquid steel and 41% of liquid aluminium produced does not make it into final products, but is diverted as process scrap and recycled. Reducing scrap substitutes production by recycling and could reduce total energy use by 17% and 6% and total CO 2 emissions by 16% and 7% for the steel and aluminium industries respectively, using forming and fabrication energy values from the case studies. The abatement potential of process scrap elimination is similar in magnitude to worldwide implementation of best available standards of energy efficiency and demonstrates how decreasing the recycled content may sometimes result in emission reductions. Evidence from the case studies suggests that whilst most companies are aware of their own yield ratios, few, if any, are fully aware of cumulative losses along their whole supply chain. Addressing yield losses requires this awareness to motivate collaborative approaches to improvement. © 2011 Elsevier B.V. All rights reserved.

Towards a process framework for assessing the potential value of technologies

Current technology valuation literature predominantly focuses on explaining the merits and implications of specific tools, but little research is available that takes a contextual process perspective. The aim of this paper is to further develop an integrative process framework that supports the structuring of the valuation process and the more systematic choice of valuation techniques for new technologies. The paper starts by reviewing key concepts and issues that surround the assessment of technology investments and the evidence of what companies use. Many factors need to be brought into the appraisal process, reflecting technological and market conditions. While there is usually a desire to reduce the assessment to a financial value, it is also widely appreciated that there is long term strategic value in securing a technological lead, which is difficult, or even inappropriate, to assess in purely financial terms. The multiple factors involved in the evaluation activity are identified with respect to the changing nature of the appraisal process as the technology matures and the implications for associated tools. The result of the literature review is a process framework which provides a conceptual basis for integrating valuation techniques. This framework is then populated with the results of industrial case studies on technology valuation to allow conclusions on its applicability to be drawn. © 2011 IEEE.

The technical potential for reducing metal requirements through lightweight product design

Metal production consumes around 10% of all global energy, so is a significant driver of climate change and other concerns about sustainability. Demand for metal is rising and forecast to double by 2050 through a combination of growing total demand from developing countries, and ongoing replacement demand in developed economies. Metal production is already extremely efficient, so the major opportunities for emissions abatement in the sector are likely to arise from material efficiency - using less new metal to meet demand for services. Therefore this paper examines the opportunity to reduce requirements for steel and aluminium by lightweight design. A set of general principles for lightweight design are proposed by way of a simple analytical example, and are then applied to five case study products which cumulatively account for 30% of global steel product output. It is shown that exploiting lightweight design opportunities for these five products alone could reduce global steel requirements by 5%, and similar savings in aluminium products could reduce global aluminium requirements by 7%. If similar savings to those in the design case studies were possible in all steel and aluminium products, total material requirements could be reduced by 25-30%. However, many of these light-weighting measures are, at present, economically unattractive, and may take many years to implement. © 2011 Elsevier B.V. All rights reserved.