Spectral measurement of diode lasers with a single-mode birefringent fibre

A new, and very simple spectrometer based on birefringent fiber is described. A resolution of 0.02 angstrom has been achieved, and the system has been used to measure diode laser chirp. A length of 10km of fiber would be sufficient to resolve single mode line widths.

Experimental analysis of SCM-based transmission over 500 m of FDDI-grade multimode fiber with enhancement from electronic equalization

Experimental analysis is applied for the first time to identify optimal launch conditions and carrier frequencies for SCM transmission over worst-case MMF. Potential for performance enhancement using electronic equalization is demonstrated for the first time. © 2006 Optical Society of America.

Mode-controlled vertical cavity surface emitting lasers for bandwidth enhancement of multimode fibre links

A GaAs Vertical Cavity Surface Emitting Laser (VCSEL) that generates controlled modes offset from the center is described. The device is modulated with a 27-1 pseudo-random bit sequence and its output is transmitted along a 1 km length of multimode fiber (MMF). Open eyes are obtained for data rates as high as 1.4Gb/s. The transmission bandwidth increases by a factor of 4 over over-filled launch (OFL). This enhancement is stable against environment influences on the fiber.

10-Gbit/s transmission over 300-m standard multimode fiber using multilevel coding and 2-channel WDM

A combination of multilevel coding schemes and simple two-channel wavelength division multiplexing (WDM) at 1300 and 1550 nm was used to transmit an aggregate of 10 Gbit/s over 300 m of multimode fiber that is typical of that employed in current Local Area Networks (LANs). It was shown that this technique could be a simple solution for achieving 10 Gigabit ethernet links over installed multimode fiber building backbones.

Subcarrier modulation for transmission of 1-Gbit/s channels over 500 m of 62.5-μm multimode fiber

The use of two different subcarriers at frequencies up to 5.5 GHz each transmitting 1 Gbit/s over 500 m of multimode fiber (MMF) is demonstrated. By transmitting the two subcarrier channels simultaneously alongside the baseband signal, an aggregate bit rate of 2.8 Gbit/s is possible.

Uncooled, 10Gb/s operation of two-contact InGaAsP lasers with low drive current

Uncooled, high-speed modulation of two-contact lasers is presented with ultra-low drive currents. Practical operation at 10Gb/s up to temperatures of 85°C and extinction ratios of 6dB are found for current swings which are less than 40% of conventional lasers.

Waveguide lasers in Er:Yb-doped phosphate glass fabricated by femtosecond laser writing

Advanced waveguide lasers, operating both in continuous wave and pulsed regimes, have been realized in an active phosphate glass by direct writing with femtosecond laser pulses. Stable single mode operation was obtained; the laser provided more than 50 m W in single longitudinal and transverse mode operation with 21% slope efficiency. Furthermore, by combining a high gain waveguide and an innovated fiber-pigtailed saturable absorber based on carbon nanotubes, a mode-locked ring laser providing transform limited 1.6 ps pulses was demonstrated. © 2007 IEEE.

Ultrafast and high-energy pulsed lasers with graphene mode-lockers

The conventional technology for generating ultrashort pulses relies on soliton-like operation based mode-locking. In this regime, the pulse duration is limited by nonlinear optical effects[1]. One method to mitigate these effects is to alternate segments of normal and anomalous group velocity dispersion (GVD) fiber[1]. This configuration is known as dispersion-managed soliton design. It decreases the nonlinear optical effects and reduces the pulse duration[1]. © 2011 IEEE.

Fiber laser processing of amorphous rare earth NeFeB magnetic materials

Since the exchange coupling theory was proposed by Kneller and Hawig in 1991 there has been a significant effort within the magnetic materials community to enhance the performance of rare earth magnets by utilising nano-composite meta-materials. Inclusions of magnetically soft iron smaller than approximately 10 nm in diameter are exchange coupled to a surrounding magnetically hard Nd2Fe14B matrix and provide an enhanced saturisation magnetisation without reducing coercivity. For such a fine nanostructure to be produced, close control over the thermal history of the material is needed. A processing route which provides this is laser annealing from an amorphous alloy precursor. In the current work, relationships between laser parameters, thermal histories of laser processed amorphous stoichiometric NdFeB ribbons and the magnetic properties of the resulting nanocrystalline products have been determined with a view to applying the process to thick film nanocomposite magnet production.

Design of carbon nanotube fiber microelectrode for glucose biosensing

BACKGROUND: Carbon nanotube (CNT) fiber directly spun from an aerogel has a unique, well-aligned nanostructure (nano-pore and nano-brush), and thus provides high electro-catalytic activity and strong interaction with glucose oxidase enzyme. It shows great potential as a microelectrode for electrochemical biosensors. RESULTS: Cyclic voltammogram results indicate that post-synthesis treatments have great influence on the electrocatalytic activity of CNT fibers. Raman spectroscopy and electrical conductivity tests suggest that fibers annealed at 250 °C remove most of the impurities without damaging the graphite-like structure. This leads to a nano-porous morphology on the surface and the highest conductivity value (1.1 × 10 5 S m -1). Two CNT fiber microelectrode designs were applied to enhance their electron transfer behaviour, and it was found that a design using a 30 nm gold coating is able to linearly cover human physiological glucose level between 2 and 30 mmol L -1. The design also leads to a low detection limit of 25 μmol L -1. CONCLUSIONS: The high performance of CNT fibers not only offers exceptional mechanical and electrical properties, but also provides a large surface area and electron transfer pathway. They consequently make excellent bioactive microelectrodes for glucose biosensing, especially for potential use in implantable devices. © 2011 Society of Chemical Industry.

500 fs wideband tunable fiber laser mode-locked by nanotubes

Sub-picosecond tunable ultrafast lasers are important tools for many applications. Here we present an ultrafast tunable fiber laser mode-locked by a nanotube based saturable absorber. The laser outputs ∼500fs pulses over a 33 nm range at 1.5μm. This outperforms the current achievable pulse duration from tunable nanotube mode-locked lasers. © 2012 Elsevier B.V. All rights reserved.