ANALYSIS OF A PROBLEM INVOLVING RADIAL CONSOLIDATION.

An analytical solution is presented for the vertical consolidation of a cylindrical annulus of clay with horizontal drainage occurring to concentric internal and external drainage boundaries. Numerical results are given for various ratios of internal and external radii and it is shown that solutions for conventional one-dimensional consolidation, and for consolidation of a cylindrical block of clay with drainage only to the outer cylindrical boundary form extremes to the analysis presented here. An application of the solution to the estimation of horizontal permeability of clay is briefly described.

Experimental study of tip clearance flow in a radial inflow turbine

This paper describes an experimental investigation of tip clearance flow in a radial inflow turbine. Flow visualization and static pressure measurements were performed. These were combined with hot-wire traverses into the tip gap. The experimental data indicates that the tip clearance flow in a radial turbine can be divided into three regions. The first region is located at the rotor inlet, where the influence of relative casing motion dominates the flow over the tip. The second region is located towards midchord, where the effect of relative casing motion is weakened. Finally a third region exists in the exducer, where the effect of relative casing motion becomes small and the leakage flow resembles the tip flow behaviour in an axial turbine. Integration of the velocity profiles showed that there is little tip leakage in the first part of the rotor because of the effect of scraping. It was found that the bulk of tip leakage flow in a radial turbine passes through the exducer. The mass flow rate, measured at four chordwise positions, was compared with a standard axial turbine tip leakage model. The result revealed the need for a model suited to radial turbines. The hot-wire measurements also indicated a higher tip gap loss in the exducer of the radial turbine. This explains why the stage efficiency of a radial inflow turbine is more affected by increasing the radial clearance than by increasing the axial clearance.

Laminar and turbulent radial jets

In this paper the radial free jet which is produced by a continuous discharge of fluid from the space between two identical, parallel, circular, concentric discs into an infinite region of stagnant fluid of the same density and viscosity is investigated. Both laminar and turbulent jets are considered with analytical solutions being obtained near to the origin of the jet and at large distances along the jet. These asymptotic solutions are matched using a computational technique, and the numerical predictions show very good agreement with all the available experimental data.

Long range exhaustion-a mathematical model for the axisymmetric air flow of a local exhaust ventilation hood assisted by a turbulent radial jet

Abstract-Mathematical modelling techniques are used to predict the axisymmetric air flow pattern developed by a state-of-the-art Banged exhaust hood which is reinforced by a turbulent radial jet flow. The high Reynolds number modelling techniques adopted allow the complexity of determining the hood's air Bow to be reduced and provide a means of identifying and assessing the various parameters that control the air Bow. The mathematical model is formulated in terms of the Stokes steam function, ψ, and the governing equations of fluid motion are solved using finite-difference techniques. The injection flow of the exhaust hood is modelled as a turbulent radial jet and the entrained Bow is assumed to be an inviscid potential flow. Comparisons made between contours of constant air speed and centre-line air speeds deduced from the model and all the available experimental data show good agreement over a wide range of typical operating conditions. | Mathematical modelling techniques are used to predict the axisymmetric air flow pattern developed by a state-of-the-art flanged exhaust hood which is reinforced by a turbulent radial jet flow. The high Reynolds number modelling techniques adopted allow the complexity of determining the hood's air flow to be reduced and provide a means of identifying and assessing the various parameters that control the air flow. The mathematical model is formulated in terms of the Stokes steam function, Ψ, and the governing equations of fluid motion are solved using finite-difference techniques. The injection flow of the exhaust hood is modelled as a turbulent radial jet and the entrained flow is assumed to be an inviscid potential flow. Comparisons made between contours of constant air speed and centre-line air speeds deduced from the model and all the available experimental data show good agreement over a wide range of typical operating conditions.

Structural and optical properties of axial and radial heterostructure III-V nanowires grown by metalorganic chemical vapour deposition

We have investigated the structural properties and photoluminescence of novel axial and radial heterostructure III-V nanowires, fabricated by metalorganic chemical vapour deposition. Segments of InGaAs have been incorporated within GaAs nanowires, to create axial heterostructure nanowires which exhibit strong photoluminescence. Photoluminescence is observed from radial heterostructure nanowires (core-shell nanowires), consisting of GaAs cores with AlGaAs shells. Core-multishell nanowires, of GaAs cores clad in several alternating layers of thick AlGaAs barrier shells and thin GaAs quantum well shells, exhibit a blue-shifted photoluminescence peak arising from quantum confinement effects. © 2006 Crown Copyright.

Investigation of a radial-inflow bleed as a potential for compressor clearance control

The mismatch in thermal response between a High Pressure Compressor (HPC) drum and casing is a limiting factor in the reduction of compressor clearance. An experimental test rig has been used to demonstrate the concept of radial inflow to reduce the thermal time constant of HPC discs. The testing uses a simulated idle - Maximum Take Off (MTO) - idle transient in order to measure the thermal response directly. The testing is fully scaled in the dimensionless sense to engine conditions. A simple closure model based on lumped capacitance is used to illustrate the scope of potential benefits. The proof-of-concept testing shows that HPC disc time constant reductions of the order 2 are feasible with a radial-inflow bleed of only 4% of bore flow at scaled MTO conditions. Using the experimental results, the simple closure modelling suggests that for a stage with a significant mismatch in thermal response, reductions in 2D axis-symmetric clearance of as much as 50% at MTO conditions may be possible along with significant scope for improvements at cruise conditions. Copyright © 2013 by ASME.

Manufacturing dish shaped rings on radial-axial ring rolling mills

Ring rolling is an established method to produce seamless rings of different cross-sectional geometries. For dish shaped rings, there are applications in different areas such as offshore, aeronautics or the energy sector. At the moment, dish shaped rings are produced by machining of rings with rectangular shaped cross section, by (open die) hollow forging on a conical mandrel or by using shaped ring rolling tools. These ways of manufacturing have the disadvantage of high material waste, additional costs for special tools, long process time and limited or inflexible geometries. Therefore, the manufacturing of dish shaped rings on conventional radial-axial ring rolling mills would expand the range of products for ring producers. The aim of this study is to investigate the feasibility of an alternative to the current manufacturing processes, without requiring additional tooling and material costs. Therefore, the intended formation of dish shaped rings-previously regarded as a form error-is investigated. Based on an analysis of geometrical requirements and metal flow mechanisms, a rolling strategy is presented, causing dishing and ring climbing by a large height reduction of the ring. Using this rolling strategy dish shaped rings with dishing angles up to 18° were achieved. In addition to the experiments finite element method (FEM)-simulations of the process have been successfully conducted, in order to analyze the local strain evolution. However, when the contact between ring and main roll is lost in the process the ring starts to oscillate around the mandrel and neither dishing nor ring climbing is observed. © 2013 German Academic Society for Production Engineering (WGP).