Long term peripheral nerve regeneration using a novel PCL nerve conduit.

The gold standard in surgical management of a peripheral nerve gap is currently autologous nerve grafting. This confers patient morbidity and increases surgical time therefore innovative experimental strategies towards engineering a synthetic nerve conduit are welcome. We have developed a novel synthetic conduit made of poly ε-caprolactone (PCL) that has demonstrated promising peripheral nerve regeneration in short-term studies. This material has been engineered to permit translation into clinical practice and here we demonstrate that histological outcomes in a long-term in vivo experiment are comparable with that of autologous nerve grafting. A 1cm nerve gap in a rat sciatic nerve injury model was repaired with a PCL nerve conduit or an autologous nerve graft. At 18 weeks post surgical repair, there was a similar volume of regenerating axons within the nerve autograft and PCL conduit repair groups, and similar numbers of myelinated axons in the distal stump of both groups. Furthermore, there was evidence of comparable re-innervation of end organ muscle and skin with the only significant difference the lower wet weight of the muscle from the PCL conduit nerve repair group. This study stimulates further work on the potential use of this synthetic biodegradable PCL nerve conduit in a clinical setting.

Structural and optical properties of axial and radial heterostructure III-V nanowires grown by metalorganic chemical vapour deposition

We have investigated the structural properties and photoluminescence of novel axial and radial heterostructure III-V nanowires, fabricated by metalorganic chemical vapour deposition. Segments of InGaAs have been incorporated within GaAs nanowires, to create axial heterostructure nanowires which exhibit strong photoluminescence. Photoluminescence is observed from radial heterostructure nanowires (core-shell nanowires), consisting of GaAs cores with AlGaAs shells. Core-multishell nanowires, of GaAs cores clad in several alternating layers of thick AlGaAs barrier shells and thin GaAs quantum well shells, exhibit a blue-shifted photoluminescence peak arising from quantum confinement effects. © 2006 Crown Copyright.

Investigation of a radial-inflow bleed as a potential for compressor clearance control

The mismatch in thermal response between a High Pressure Compressor (HPC) drum and casing is a limiting factor in the reduction of compressor clearance. An experimental test rig has been used to demonstrate the concept of radial inflow to reduce the thermal time constant of HPC discs. The testing uses a simulated idle - Maximum Take Off (MTO) - idle transient in order to measure the thermal response directly. The testing is fully scaled in the dimensionless sense to engine conditions. A simple closure model based on lumped capacitance is used to illustrate the scope of potential benefits. The proof-of-concept testing shows that HPC disc time constant reductions of the order 2 are feasible with a radial-inflow bleed of only 4% of bore flow at scaled MTO conditions. Using the experimental results, the simple closure modelling suggests that for a stage with a significant mismatch in thermal response, reductions in 2D axis-symmetric clearance of as much as 50% at MTO conditions may be possible along with significant scope for improvements at cruise conditions. Copyright © 2013 by ASME.

Manufacturing dish shaped rings on radial-axial ring rolling mills

Ring rolling is an established method to produce seamless rings of different cross-sectional geometries. For dish shaped rings, there are applications in different areas such as offshore, aeronautics or the energy sector. At the moment, dish shaped rings are produced by machining of rings with rectangular shaped cross section, by (open die) hollow forging on a conical mandrel or by using shaped ring rolling tools. These ways of manufacturing have the disadvantage of high material waste, additional costs for special tools, long process time and limited or inflexible geometries. Therefore, the manufacturing of dish shaped rings on conventional radial-axial ring rolling mills would expand the range of products for ring producers. The aim of this study is to investigate the feasibility of an alternative to the current manufacturing processes, without requiring additional tooling and material costs. Therefore, the intended formation of dish shaped rings-previously regarded as a form error-is investigated. Based on an analysis of geometrical requirements and metal flow mechanisms, a rolling strategy is presented, causing dishing and ring climbing by a large height reduction of the ring. Using this rolling strategy dish shaped rings with dishing angles up to 18° were achieved. In addition to the experiments finite element method (FEM)-simulations of the process have been successfully conducted, in order to analyze the local strain evolution. However, when the contact between ring and main roll is lost in the process the ring starts to oscillate around the mandrel and neither dishing nor ring climbing is observed. © 2013 German Academic Society for Production Engineering (WGP).