Model-based control of a Rijke tube combustion instability

A Rijke tube is used to demonstrate model-based control of a combustion instability, where controller design is based on measurement of the unstable system. The Rijke tube used was of length 0.75m and had a grid-stabilised laminar flame in its lower half. A microphone was used as a sensor and a loudspeaker as an actuator for active control. The open loop transfer function (OLTF) required for controller design was that from the actuator to the sensor. This was measured experimentally by sending a signal with two components to the actuator. The first was a control component from an empirically designed controller, which was used to stabilise the system, thus eliminating the non-linear limit cycle. The second was a high bandwidth signal for identification of the OLTF. This approach to measuring the OLTF is generic and can be applied to large-scale combustors. The measured OLTF showed that only the fundamental mode of the tube was unstable; this was consistent with the OLTF predicted by a mathematical model of the tube, involving 1-D linear acoustic waves and a time delay heat release model. Based on the measured OLTF, a controller to stabilise the instability was designed using Nyquist techniques. This was implemented and was seen to result in an 80dB reduction in the microphone pressure spectrum. A robustness study was performed by adding an additional length to the top of the Rijke tobe. The controller was found to achieve control up to an increase in tube length of 19%. This compared favourably with the empirical controller, which lost control for an increase in tube length of less than 3%.

Model based learning of sigma points in unscented Kalman filtering

The unscented Kalman filter (UKF) is a widely used method in control and time series applications. The UKF suffers from arbitrary parameters necessary for a step known as sigma point placement, causing it to perform poorly in nonlinear problems. We show how to treat sigma point placement in a UKF as a learning problem in a model based view. We demonstrate that learning to place the sigma points correctly from data can make sigma point collapse much less likely. Learning can result in a significant increase in predictive performance over default settings of the parameters in the UKF and other filters designed to avoid the problems of the UKF, such as the GP-ADF. At the same time, we maintain a lower computational complexity than the other methods. We call our method UKF-L. ©2010 IEEE.

Model-based thermoacoustic oscillation control via ℋ ∞ loop-shaping and integral quadratic constraints

Lean premixed prevaporized (LPP) technology has been widely used in the new generation of gas turbines in which reduced emissions are a priority. However, such combustion systems are susceptible to the damage of self-excited oscillations. Feedback control provide a way of preventing such dynamic stabilities. A flame dynamics assumption is proposed for a recently developed unsteady heat release model, the robust design technique, ℋ ∞ loop-shaping, is applied for the controller design and the performance of the controller is confirmed by simulations of the closed-loop system. The Integral Quadratic Constraints(IQC) method is employed to prove the stability of the closed-loop system. ©2010 IEEE.

Model-based approaches to handling additive noise in reverberant environments

Model-based approaches to handle additive and convolutional noise have been extensively investigated and used. However, the application of these schemes to handling reverberant noise has received less attention. This paper examines the extension of two standard additive/convolutional noise approaches to handling reverberant noise. The first is an extension of vector Taylor series (VTS) compensation, reverberant VTS, where a mismatch function including reverberant noise is used. The second scheme modifies constrained MLLR to allow a wide-span of frames to be taken into account and projected into the required dimensionality. To allow additive noise to be handled, both these schemes are combined with standard VTS. The approaches are evaluated and compared on two tasks, MC-WSJ-AV, and a reverberant simulated version of AURORA-4. © 2011 IEEE.

A process model based methodology to support conflict management

The product design development has increasingly become a collaborative process. Conflicts often appear in the design process due to multi-actors interactions. Therefore, a critical element of collaborative design would be conflict situations resolution. In this paper, a methodology, based on a process model, is proposed to support conflict management. This methodology deals mainly with the conflict resolution team identification and the solution impact evaluation issues. The proposed process model allows the design process traceability and the data dependencies network identification; which making it be possible to identify the conflict resolution actors as well as to evaluate the selected solution impact. Copyright © 2006 IFAC.

An ecodesign model based on industry experience

With the increase in environmental legislation facing many industrial sectors organisations are now looking for ways to improve their environmental performance. To a large extent organisations have tended to concentrate on their operations inside the "factory gates" with little regard to the environmental performance of the products they produce. However, this is now changing and some organisations are beginning to take a close look at their products and their effects on the environment during its use phase as well as during the manufacture and disposal phases. At Cranfield University we have carried out a 3 year survey of US, Central European and UK companies claiming to practice ecodesign has been undertaken. Thirty electrical and electronic manufacturers were studied, some through in-depth observation of design programmes, most through semi-structured interviews. The survey and action research sought to understand the way in which these companies practised ecodesign and how they .had implemented ecodesign. A common pattern emerged from the data which suggests that companies successfully implementing ecodesign have many similar experiences. The resulting ecodesign model is presented and discussed, and the factors critical to successful implementation at various stages are explored. The factors cover a range of topics including design management, motivation, design tools, design phases, communication and the designers perspective.