Continuous dynamical systems that realize discrete optimization on the hypercube

We study the problem of finding a local minimum of a multilinear function E over the discrete set {0,1}n. The search is achieved by a gradient-like system in [0,1]n with cost function E. Under mild restrictions on the metric, the stable attractors of the gradient-like system are shown to produce solutions of the problem, even when they are not in the vicinity of the discrete set {0,1}n. Moreover, the gradient-like system connects with interior point methods for linear programming and with the analog neural network studied by Vidyasagar (IEEE Trans. Automat. Control 40 (8) (1995) 1359), in the same context. © 2004 Elsevier B.V. All rights reserved.

A novel process for transforming sheet metal blanks: Ridged die forming

Up to 20% of all sheet metal produced is scrapped as blanking skeletons. A novel process is therefore designed and examined, aiming to transform tessellating 'pre-blanks' in-plane into the real blanks required for stamping. Prior to blanking, the sheet is formed with a set of ridged dies, from which pre-blanks are cut and then flattened into true blanks. Several different approaches to designing ridged dies are evaluated by simulation and experiment, and the best results demonstrate a potential reduction in blanking yield losses for can-making from 9.3% to 6.9%. © 2013 CIRP.

An experimental study of loss sources in a fan operating with continuous inlet stagnation pressure distortion

The viability of Boundary Layer Ingesting (BLI) engines for future aircraft propulsion is dependent on the ability to design robust, efficient engine fan systems for operation with continuously distorted inlet flow. A key step in this process is to develop an understanding of the specific mechanisms by which an inlet distortion affects the performance of a fan stage. In this paper, detailed full-annulus experimental measurements of the flow field within a low-speed fan stage operating with a continuous 60-degree inlet stagnation pressure distortion are presented. These results are used to describe the three-dimensional fluid mechanics governing the interaction between the fan and the distortion and to make a quantitative assessment of the impact on loss generation within the fan. A 5.3 percentage point reduction in stage total-to-total efficiency is observed as a result of the inlet distortion. The reduction in performance is shown to be dominated by increased loss generation in the rotor due to off-design incidence values at its leading edge, an effect which occurs throughout the annulus despite the localised nature of the inlet distortion. Increased loss generation in the stator row is also observed due to flow separations that are shown to be caused by whirl angle distortion at rotor exit. By addressing these losses, it should be possible to achieve improved efficiency in BLI fan systems. Copyright © 2012 by ASME.

Continuous weak measurement of a trapped electron using a percolation field effect transistor

We investigate the use of a percolation-field-effect-transistor for the continuous weak measurement of a spatially Rabi oscillating trapped electron through the change in percolation pathway of the transistor channel. In contrast to conventional devices, this detection mechanism in principle does not require a change in the stored energy of the gate capacitance to modify the drain current, so reducing the measurement back-action. The signal-to-noise ratio and measurement bandwidth are seen to be improved compared to conventional devices, allowing further aspects of the dynamic behaviour to be observed. © 2013 AIP Publishing LLC.

An experimental study of loss sources in a fan operating with continuous inlet stagnation pressure distortion

The viability of boundary layer ingesting (BLI) engines for future aircraft propulsion is dependent on the ability to design robust, efficient engine fan systems for operation with continuously distorted inlet flow. A key step in this process is to develop an understanding of the specific mechanisms by which an inlet distortion affects the performance of a fan stage. In this paper, detailed full-annulus experimental measurements of the flow field within a low-speed fan stage operating with a continuous 60 deg inlet stagnation pressure distortion are presented. These results are used to describe the three-dimensional fluid mechanics governing the interaction between the fan and the distortion and to make a quantitative assessment of the impact on loss generation within the fan. A 5.3 percentage point reduction in stage total-to-total efficiency is observed as a result of the inlet distortion. The reduction in performance is shown to be dominated by increased loss generation in the rotor due to off-design incidence values at its leading edge, an effect that occurs throughout the annulus despite the localized nature of the inlet distortion. Increased loss in the stator row is also observed due to flow separations that are shown to be caused by whirl angle distortion at rotor exit. By addressing these losses, it should be possible to achieve improved efficiency in BLI fan systems. © 2013 by ASME.

Continuous asr for flexible incremental dialogue

Spoken dialogue systems provide a convenient way for users to interact with a machine using only speech. However, they often rely on a rigid turn taking regime in which a voice activity detection (VAD) module is used to determine when the user is speaking and decide when is an appropriate time for the system to respond. This paper investigates replacing the VAD and discrete utterance recogniser of a conventional turn-taking system with a continuously operating recogniser that is always listening, and using the recogniser 1-best path to guide turn taking. In this way, a flexible framework for incremental dialogue management is possible. Experimental results show that it is possible to remove the VAD component and successfully use the recogniser best path to identify user speech, with more robustness to noise, potentially smaller latency times, and a reduction in overall recognition error rate compared to using the conventional approach. © 2013 IEEE.