Investigation of anti-lock braking strategies for heavy goods vehicles

An articulated lorry was instrumented in order to measure its performance in straight-line braking. The trailer was fitted with two interchangeable tandem axle sub-chassis, one with an air suspension and the other with a steel monoleaf four-spring suspension. The brakes were only applied to the trailer axles, which were fitted with anti-lock braking systems (ABS), with the brake torque controlled in response to anticipated locking of the leading axle of the tandem. The vehicle with the air suspension was observed to have significantly better braking performance than the steel suspension, and to generate smaller inter-axle load transfer and smaller vertical dynamic tyre forces. Computer models of the two suspensions were developed, including their brakes and anti-lock systems. The models were found to reproduce most of the important features of the experimental results. It was concluded that the poor braking performance of the steel four-spring suspension was mainly due to interaction between the ABS and inter-axle load transfer effects. The effect of road roughness was investigated and it was found that vehicle stopping distances can increase significantly with increasing road roughness. Two alternative anti-lock braking control strategies were simulated. It was found that independent sensing and actuation of the ABS system on each wheel greatly reduced the difference in stopping distances between the air and steel suspensions. A control strategy based on limiting wheel slip was least susceptible to the effects of road roughness.

An experimental semi-active anti-roll system

The use of anti-roll bars to provide additional roll stiffness and therefore to reduce the trade-off between ride and rollover performance has previously been studied. However, little work has been carried out to investigate the benefits of a switchable roll stiffness. Such a semi-active anti-roll system has the ability to have a low roll stiffness during straight-ahead driving for improved ride performance and high roll stiffness during cornering for improved roll performance. Modelling of such a system is conducted and the model is validated against a semi-active anti-roll system fitted to an experimental vehicle. Experimental and theoretical investigations are used to investigate the performance of such a system with several different strategies employed to switch to the high-stiffness state. The use of an air suspension on the vehicle to roll into corners is also investigated, as is the possibility of exploiting the road layout by allowing the vehicle to be in a low-roll-stiffness configuration during a corner, and then to switch to the high-roll-stiffness configuration midcorner, hence 'locking in' a roll angle. The best rollover performance improvement that was achieved was 12.5 per cent. © IMechE 2008.

Study on the critical submergence of surface vortices and the design of anti-vortex intakes

Surface vortex behavior in front of the tunnel intake was investigated in this paper. The critical submergence of vortex was discussed based on the concept of 'critical spherical sink surface' (CSSS). The vortex formation and evolution at the tunnel intake were analyzed based on the theory of CSSS considering the effect of circulation. A theory was proposed to explain the surface vortex. The theoretical development was verified by the physical model experiments of Xiluodu hydropower station. The radial velocity and vortex circulation were considered as the main factors that influence the formation and evolution of surface vortex. Finally, an anti-vortex intake configuration was proposed to weaken the air-core vortex in front of the tunnel intakes of the hydraulic structures. © 2011 Science China Press and Springer-Verlag Berlin Heidelberg.

Uncooled DWDM transmission system using tunable laser sources with anti-mode-hop control protocol

We propose an uncooled DWDM system where errors from uncontrolled laser mode-hopping are avoided by using a control protocol based on monitoring SMSR. We describe a proof-of-principle demonstration of a novel uncooled 50GHz DWDM system. © 2011 IEEE.

Anti-counterfeiting and supply chain security

Counterfeit trade developed into a severe problem for many industries. While established security features such as holograms, micro printings or chemical markers do not seem to efficiently avert trade in illicit imitation products, RFID technology, with its potential to automate product authentications, may become a powerful tool to enhance brand and product protection. The following contribution contains an overview on the implication of product counterfeiting on affected companies, provides a starting point for a structured requirements definition for RFID-based anti-counterfeiting systems, and outlines several principal solution approaches that are discussed in greater detail in the subsequent chapters. © 2008 Springer-Verlag Berlin Heidelberg.