Sound radiation from point-excited structures: Comparison of plate and sphere

Acoustic radiation from a structure can be expressed in terms of modal radiation and modal coefficients. This paper investigates the contributions of these two modal properties to radiation excited by a point force. Sound radiation from two basic structures is considered: a baffled rectangular plate and a closed spherical shell. The plate behaviour is familiar, and governed by the relation between the natural frequency of a mode and its coincidence frequency. For a closed spherical shell, there are either zero or two critical frequencies, depending on the radius and thickness. When there are two the shell radiates well both above and below the two frequencies, and poorly in the frequency range between them. © 2012 Elsevier Ltd. All rights reserved.

Effects of multi-scattering on the performance of a single-beam acoustic manipulation device.

The effects of multiple scattering on acoustic manipulation of spherical particles using helicoidal Bessel-beams are discussed. A closed-form analytical solution is developed to calculate the acoustic radiation force resulting from a Bessel-beam on an acoustically reflective sphere, in the presence of an adjacent spherical particle, immersed in an unbounded fluid medium. The solution is based on the standard Fourier decomposition method and the effect of multi-scattering is taken into account using the addition theorem for spherical coordinates. Of particular interest here is the investigation of the effects of multiple scattering on the emergence of negative axial forces. To investigate the effects, the radiation force applied on the target particle resulting from a helicoidal Bessel-beam of different azimuthal indexes (m = 1 to 4), at different conical angles, is computed. Results are presented for soft and rigid spheres of various sizes, separated by a finite distance. Results have shown that the emergence of negative force regions is very sensitive to the level of cross-scattering between the particles. It has also been shown that in multiple scattering media, the negative axial force may occur at much smaller conical angles than previously reported for single particles, and that acoustic manipulation of soft spheres in such media may also become possible.

Predicting the acoustics of squeak and rattle

This paper discusses the development of a computationally efficient numerical method for predicting the acoustics of rattle events upfront in the design cycle. The method combines Finite Elements, Boundary Elements and SEA and enables the loudness of a large number of rattle events to be efficiently predicted across a broad frequency range. A low frequency random vibro-acoustic model is used in conjunction with various closed form analytical expressions in order to quickly predict impact probabilities and locations. An existing method has been extended to estimate the statistics of the contact forces across a broad frequency range. Finally, broadband acoustic radiation is predicted using standard low, mid and high frequency vibro-acoustic methods and used to estimate impact loudness. The approach is discussed and a number of validation examples are presented.

Influence of tire geometry on the horn effect

A reciprocal-configuration Boundary Element Method calculation of acoustic radiation characteristics has been implemented for a generic tire geometry. The influence of the geometric parameters on the radiation characteristics has been studied. The degree of amplification of noise sources on the tire belt is strongly affected by the overall tire width. In contrast, the tire radius predominantly influences the pattern of the varying amplification around the belt, rather than its absolute level. Radiusing the tire's 'shoulder' region is potentially beneficial in terms of lowering amplification levels, for a tire of fixed overall width. However, it is less effective than maintaining sharp shoulders and reducing the overall width. Thus, for an acoustically optimal belted tire, the overall width should be as small as possible, even if this leads to a larger diameter. The width should not be increased in order to accommodate a radiused crown region. Copyright © (2012) by the Institute of Noise Control Engineering (INCE).

Measurements of thermal radiation in ultralight metal foams with open cells

Highly porous ultralightweight cellular metal foams with open cells have attractive mechanical, thermal, acoustic and other properties and are currently being exploited for high-temperature applications (e.g. acoustic liners for combustion chambers). In such circumstances, thermal radiation in the metal foam becomes a significant mechanism of heat transfer. This paper presents results from experimental measurements on radiative transfer in Fe-Cr-Al-Y (a steel-based high-temperature alloy) foams having high porosity (95 per cent) and different cell sizes, manufactured at low cost from the sintering route. The spectral transmittance and reflectance are measured at different infrared wavelengths ranging from 2.5 to 50 μm, which are subsequently used to determine the extinction coefficient and foam emissivity. The results show that the spectral quantities are strongly dependent on the wavelength, particularly in the short-wavelength regime (less than 25 μm). While the extinction coefficient decreases with increasing cell size, the effect of cell size on foam reflectance is not significant. When the temperature is increased, the total extinction coefficient increases but the total reflectance decreases. The effective radiative conductivity of the metal foam is obtained by using the guarded hot-plate apparatus. With the porosity fixed, the effective radiative conductivity increases with increasing cell size and increasing temperature. © IMechE 2004.