Canonical normal shock wave/boundary-layer interaction flows relevant to external compression inlets

The normal shock wave/boundary-layer interaction is important to the operation and performance of a supersonic inlet, and the normal shock wave/boundary-layer interaction is particularly prominent in external compression inlets. To improve understanding of such interactions, it is helpful to make use of fundamental flows that capture the main elements of inlets, without resorting to the level of complexity and system integration associated with full-geometry inlets. In this paper, several fundamental flowfield configurations have been considered as possible test cases to represent the normal shock wave/boundary-layer interaction aspects found in typical external compression inlets, and it was found that the spillage diffuser more closely retains the basic flow features of an external compression inlet than the other configurations. In particular, this flowfield allows the normal shock Mach number as well as the amount and rate of subsonic diffusion to all be held approximately constant and independent of the application of flow control. In addition, a survey of several external compression inlets was conducted to quantify the flow and geometric parameters of the spillage diffuser relevant to actual inlets. The results indicated that such a flow may be especially relevant if the terminal Mach number is about 1.3 to 1.4, the confinement parameter is around 10%, and the width is around twice or three times the height. In addition, the area expansion downstream of the shock should be limited to the conservative side of incipient stall based on incompressible diffusers. Copyright © 2013 by the authors.

Models for acoustic propagation through turbofan exhaust flows

Turbomachinery noise radiating into the rearward arc is an important problem. This noise is scattered by the trailing edges of the nacelle and the jet exhaust, and interacts with the shear layers between the external flow, bypass stream and jet, en route to the far field. In the past a range of relevant model problems involving semi-infinite cylinders have been solved. However, one limitation of previous solutions is that they do not allow for the jet nozzle to protrude a finite distance beyond the end of the nacelle (or in certain configurations being buried a finite distance upstream). In this paper we use the matrix Wiener-Hopf technique, which will allow precisely the finite nacelle-jet nozzle separation to be included. The crucial step in our work is to factorise a certain matrix as a product of terms analytic and invertible in the upper/lower halves of the complex plane. The way we do this matrix factorisation is quite different in the buried and protruding nozzle cases. In the buried case our solution method is the so-called pole-removal technique. In the technically more demanding protruding case, however, we must first use Pade approximants to generate a uniformly-valid, meromorphic representation of a certain function, before the same pole-removal method can be applied. Sample results are presented, investigating in particular the effects of exit plane stagger. © 2007 by B Veitch and N Peake.

High-order detached eddy simulation, zonal LES and URANS of cavity and labyrinth seal flows

Hybrid numerical large eddy simulation (NLES), detached eddy simulation (DES) and URANS methods are assessed on a cavity and a labyrinth seal geometry. A high sixth-order discretization scheme is used and is validated using the test case of a two-dimensional vortex. The hybrid approach adopts a new blending function. For the URANS simulations, the flow within the cavity remains steady, and the results show significant variation between models. Surprisingly, low levels of resolved turbulence are observed in the cavity for the DES simulation, and the cavity shear layer remains two dimensional. The hybrid RANS-NLES approach does not suffer from this trait.For the labyrinth seal, both the URANS and DES approaches give low levels of resolved turbulence. The zonal Hamilton-Jacobi approach on the other had given significantly more resolved content. Both DES and hybrid RANS-NLES give good agreement with the experimentally measured velocity profiles. Again, there is significant variation between the URANS models, and swirl velocities are overpredicted. © 2013 John Wiley & Sons, Ltd.

Scaling of velocity fluctuations in off-wall boundary conditions for turbulent flows

A model for off-wall boundary conditions for turbulent flow is investigated. The objective of such a model is to circumvent the need to resolve the buffer layer near the wall, by providing conditions in the logarithmic layer for the overlying flow. The model is based on the self-similarity of the flow at different heights in the logarithmic layer. It was first proposed by Mizuno and Jiménez (2013), imposing at the boundary plane a velocity field obtained on-the-fly from an overlying region. The key feature of the model was that the lengthscales of the field were rescaled to account for the self-similarity law. The model was successful at sustaining a turbulent logarithmic layer, but resulted in some disagreements in the flow statistics, compared to fully-resolved flows. These disagreements needed to be addressed for the model to be of practical application. In the present paper, a more refined, wavelength-dependent rescaling law is proposed, based on the wavelength-dependent dynamics in fully-resolved flows. Results for channel flow show that the new model eliminates the large artificial pressure fluctuations found in the previous one, and a better agreement is obtained in the bulk properties, the flow fluctuations, and their spectral distribution across the whole domain. © Published under licence by IOP Publishing Ltd.