2D-lattice distributed reflector laser

A single-contact, mode-hop-free, single longitudinal mode laser operating cw under large signal modulation at 2.5 Gbit/s at room temperature was created by introducing a short etched region around the ridge-waveguide of a Fabry-Perot laser. The device could be suitable for use in extended range data communications applications.

Subcarrier modulation for transmission of 1-Gbit/s channels over 500 m of 62.5-μm multimode fiber

The use of two different subcarriers at frequencies up to 5.5 GHz each transmitting 1 Gbit/s over 500 m of multimode fiber (MMF) is demonstrated. By transmitting the two subcarrier channels simultaneously alongside the baseband signal, an aggregate bit rate of 2.8 Gbit/s is possible.

All-optical switching in a vertical coupler space switch employing photocarrier-induced nonlinearity

A novel compact integrated nonlinear optical switch is demonstrated. Using a high-power picosecond pulse of 5-ps pulsewidth and 250-MHz repetition rate, all-optical switching with a contrast ratio of 23 dB has been achieved using an in-fiber input power < 14 dBm (100 pJ/pulse). The switch speed depends on the carrier sweep-out time, which can be reduced to the 10 ps range by either applying a reverse bias or by introduction of carrier recombination centers in the active layer.

The flexoelectric behaviour of a hypertwisted chiral nematic liquid crystal

The flexoelectric behaviour of a hypertwisted chiral nematic bimesogenic liquid crystal is presented. Through detailed electro-optic measurements, with particular emphasis on the switching properties, we demonstrate remarkably high optical axis tilt angles. The material studied possessed a room temperature nematic phase and aligned easily on cooling under the application of a moderate electric field. Switching times of the order of 500 μs and contrast ratios of 90:1 are readily achieved. The tilt angles, measured using the rotating analyser technique, were found to be practically temperature independent and linear with the applied field. Tilt angles of 22.5° were obtained with moderate applied fields of 9.4 V/μm whilst fields of 25 V/μm yielded tilt angles of 45°. We believe these are the highest tilt angles ever recorded for such fields. © 2001 OPA (Overseas Publishers Association) N.V. Published by license under the Gordon and Breach Science Publishers imprint, a member of the Taylor & Francis Group.

Tribological properties of mems materials measured on a small-scale device

Micro-electro-mechanical systems, MEMS, is a rapidly growing interdisciplinary technology within the general field of Micro-Systems Technology which deals with the design and manufacture of miniaturised machines with major dimensions at the scale of tens, to perhaps hundreds, of microns. Because they depend on the cube of a representative dimension, component masses and inertias rapidly become small as size decreases whereas surface and tribological effects, which often depend on area, become increasingly important. Although MEMS components and their areas of contact are small, tribological conditions, measured by contact pressures or acceptable wear rates, are demanding and technical and commercial success will require careful measurement and precise control of surface topography and properties. Fabrication of small numbers of MEMS devices designed to test potential material combinations can be prohibitively expensive and thus there is a need for small scale test facilities which mimic the contact conditions within a micro-machine without themselves requiring processing within a full semiconductor foundry. The talk will illustrate some initial experimental results from a small-scale experimental device which meets these requirements, examining in particular the performance of Diamond-Like-Carbon coatings on a silicon substrate. Copyright © 2005 by ASME.

Enhanced flexoelectric switching behaviour in the chiral nematic phase

In order to develop materials that exhibit enhanced flexoelectric switching in the chiral nematic phase we have identified mesogenic units that display inherently strong flexoelectric coupling capabilities. Here we examine the oxycyanobiphenyl (OCB) moiety: homologues from the nOCB series exhibit significant electro-optic switching effects when doped with a highly chiral additive. Here we have examined lower dielectric anisotropy materials, since they allow the flexoelectric response to be extended to high field amplitudes. We show that dielectric coupling strength can be low in symmetric bimesogenic molecules. The flexoelectric response of such a molecular structure is tested by doping a homologue from the series CBOnOCB with a chiral additive: very significantly we find that the optic axis is rotated through 2φ=45° in <50 μs on reversing the polarity of the field (amplitude E=±6 V μm-1). Subsequently we have synthesized room temperature chiral nematic materials that exhibit 2φ≥90° at E≈10 V μm-1. © 2001 OPA (Overseas Publishers Association) N.V. Published by license under the Gordon and Breach Science Publishers imprint, a member of the Taylor & Francis Group.

Physical properties of some novel nematic bimesogens for the flexoelectric effect

In a chiral nematic liquid crystal, the flexoelectric effect consists of a fast and linear coupling with an applied electric field. One difficulty to overcome is the unwinding of the helix that occurs at higher fields due to dielectric coupling. The use of bimesogens, which possess very low molecular dielectric anisotropy can improve flexoelectric characteristics. New bimesogen compounds have recently been synthesised that exhibit switching angles of 45° for applied fields of about 9 V.μm-1. In this paper, results from dielectric, electro-optic and dynamic light scattering measurements are reported for the new bimesogenic mixture. The dielectric anisotropy Δε changes sign with temperature and its values range between -0.2 and 0.3 for the temperature range studied. For Δε weakly positive, no electric field Freedericksz transition could be induced but Williams domains are observed instead. The large decrease in the bend elastic constant to viscosity coefficient ratio is attributed to a large increase in the bend viscosity coefficient. © 2001 OPA (Overseas Publishers Association) N.V. Published by license under the Gordon and Breach Science Publishers imprint, a member of the Taylor & Francis Group.

Resonant-cavity LED transceiver arrays for optical wireless communication

155Mb/s operation of an optical wireless link is achieved by using the spectral characteristics and angular emission spectra of a 7-element tracking array of 980nm RC-LEDs. Preliminary results show extension to 200 Mb/s/channel. © 2006 Optical Society of America.

Analysis of basic processes inside the keyhole during deep penetration ND-YAG CW laser welding

During laser welding, the keyhole is generated by the recoil pressure induced by the evaporation processes occurring mainly on the front keyhole wall (KW). In order to characterize the evaporation process, we have measured this recoil pressure by using a plume deflection technique, where the plume generated for static conditions (i. e. with no sample displacement) is deflected by a transverse side gas jet. From the measurement of the plume deflection angle, the recoil pressure can be determined as a function of incident intensity and sample material. From these data one can estimate the pressure generated on the front KW, during laser welding. Therefore, the corresponding dynamic pressure exerted by the vapor plume expansion on the rear KW, in contact with the melt pool, can be also estimated. These pressures appear to be in close agreement with those generated by an additional side jet that has been used in previous experiments, for stabilizing the observed melt pool oscillations or fluctuations.

Thin film shape memory alloys and microactuators

For Micro-electro-mechanical System (MEMS) applications, TiNi-based thin film Shape Memory Alloys (SMAs) possess many desirable properties, such as high power density, large transformation stress and strain upon heating and cooling, superelasticity and biocompatibility. In this paper, recent development in TiNi-based thin film SMA and microactuator applications is discussed. The topics related to film deposition and characterisation is mainly focused on crystal nucleation and growth during annealing, film thickness effect, film texture, stress induced surface relief, wrinkling and trenches as well as Temperature Memory Effect (TME). The microactuator applications are mainly focused on microvalve and microcage for biological applications, micromirror for optical applications and data storage using nanoindentation method. Copyright © 2009, Inderscience Publishers.

Physical modelling of large area 4H-SiC PiN diodes

The recent developments in SiC PiN diode research mean that physics-based models that allow accurate, rapid prediction of switching and conduction performance and resulting converter losses will soon be required. This is especially the case given the potential for very high voltage converters to be used for enabling distributed and renewable power generation. In this work an electro-thermal compact model of a 4.5 kV silicon carbide PiN diode has been developed for converter loss modelling in Simulink. Good matching of reverse recovery has been achieved between 25 and 200 °C. The I-V characteristics of the P+ anode contact have been shown to be significant in obtaining good matching for the forward characteristics of the diode, requiring further modelling work in this area. © 2009 IEEE.

Improved infrared thermal imaging of a CMOS MEMS device

We report a technique which can be used to improve the accuracy of infrared (IR) surface temperature measurements made on MEMS (Micro-Electro-Mechanical- Systems) devices. The technique was used to thermally characterize a SOI (Silicon-On-Insulator) CMOS (Complementary Metal Oxide Semiconductor) MEMS thermal flow sensor. Conventional IR temperature measurements made on the sensor were shown to give significant surface temperature errors, due to the optical transparency of the SiO 2 membrane layers and low emissivity/high reflectivity of the metal. By making IR measurements on radiative carbon micro-particles placed in isothermal contact with the device, the accuracy of the surface temperature measurement was significantly improved. © 2010 EDA Publishing/THERMINIC.

Thermal characterization of SOI CMOS micro hot-plate gas sensors

This work reports on thermal characterization of SOI (silicon on insulator) CMOS (complementary metal oxide semiconductor) MEMS (micro electro mechanical system) gas sensors using a thermoreflectance (TR) thermography system. The sensors were fabricated in a CMOS foundry and the micro hot-plate structures were created by back-etching the CMOS processed wafers in a MEMS foundry using DRIE (deep reactive ion etch) process. The calibration and experimental details of the thermoreflectance based thermal imaging setup, used for these micro hot-plate gas sensor structures, are presented. Experimentally determined temperature of a micro hot-plate sensor, using TR thermography and built-in silicon resistive temperature sensor, is compared with that estimated using numerical simulations. The results confirm that TR based thermal imaging technique can be used to determine surface temperature of CMOS MEMS devices with a high accuracy. © 2010 EDA Publishing/THERMINIC.