A comparison of different failure assessment methodologies applied to the NESC-1 test

Predictions for a 75x205mm surface semi-elliptic defect in the NESC-1 spinning cylinder test have been made using BS PD 6493:1991, the R6 procedure, non-linear cracked body finite element analysis techniques and the local approach to fracture. All the techniques agree in predicting ductile tearing near the inner surface of the cylinder followed by cleavage initiation. However they differ in the amount of ductile tearing, and the exact location and time of any cleavage event. The amount of ductile tearing decreases with increasing sophistication in the analysis, due to the drop in peak crack driving force and more explicit consideration of constraint effects. The local approach predicts a high probability of cleavage in both HAZ and base material after 190s, while the other predictions suggest that cleavage is unlikely in the HAZ due to constraint loss, but likely in the underlying base material. The timing of this event varies from ∼150s for R6 predictions to ∼250-300s using non-linear cracked body analysis.

Effects of pedestal suppression on gain-switched laser sources for 40 Gbit/s OTDM transmission

The performance of 40 Gbit/s optical time-division multiplexed (OTDM) communication systems can be severely limited when the extinction ratio of the optical pulses is low. This is a consequence of the coherent interference noise between individual OTDM channels. When taken alone, the multiple quantum well-distributed feedback laser+dispersion compensating fiber source exhibits a relatively poor extinction ratio which impairs its potential for use in a 40 Gbit/s OTDM system. However, with the addition of an electroabsorption modulator to suppress the pulse pedestals to better than 30 dB extinction, coherent interference noise is reduced, the bit-error-rate performance is greatly improved, and the source shows good potential for 40 Gbit/s OTDM communication.

Preparation of tetrahedral amorphous carbon films by filtered cathodic vacuum arc deposition

Tetrahedrally bonded amorphous carbon (ta-C) and nitrogen doped (ta-C:N) films were obtained at room temperature in a filtered cathodic vacuum arc (FCVA) system incorporating an off-plane double bend (S-bend) magnetic filter. The influence of the negative bias voltage applied to substrates (from -20 to -350 V) and the nitrogen background pressure (up to 10-3 Torr) on film properties was studied by scanning electron microscopy (SEM), electron energy loss spectroscopy (EELS), Raman spectroscopy, X-ray photoemission spectroscopy (XPS), secondary ion mass spectroscopy (SIMS) and X-ray reflectivity (XRR). The ta-C films showed sp3 fractions between 84% and 88%, and mass densities around 3.2 g/cm3 in the wide range of bias voltage studied. In contrast, the compressive stress showed a maximum value of 11 GPa for bias voltages around -90 V, whereas for lower and higher bias voltages the stress decreased to 6 GPa. As for the ta-C:N films grown at bias voltages below -200 V and with N contents up to 7%, it has been found that the N atoms were preferentially sp3 bonded to the carbon network with a reduction in stress below 8 GPa. Further increase in bias voltage or N content increased the sp2 fraction, leading to a reduction in film density to 2.7 g/cm3.

Control of motorcycle steering instabilities

Modern high performance motorcycles often employ a steering damper producing a moment that opposes the angular velocity of the steering assembly relative to the main frame. When modeling the motorcycle in a conventional manner, the steering damper is included as an integral part of the machine. The reduction in the wobble-mode frequency is caused by the effective increase in the steering system's moment of inertia. The compensators show the potential to significantly improve the damping of both wobble and weave modes simultaneously. The dynamic characteristics of high-performance motorcycles can be improved by replacing the conventional steering damper with a passive mechanical steering compensator. The design methodology adopted uses Nyquist frequency response ideas, root-locus analysis and loop-shaping design to obtain a preliminary choice of parameters.

Value roadmapping: A structured approach for early stage technology investment decisions

Deciding to invest in early stage technologies is one of the most important tasks of technology management and arguably also the most uncertain. It assumes a particular significance in the rise of technology companies in emerging economies, which have to make appropriate investment decisions. Technology managers already have a wide range of methods and tools at their disposal, but these are mostly focussed on quantitative measures such as discounted cash flow and real options techniques. However, in the early stages of technology development there seems to be a lot of dissatisfaction with these techniques as there appears to be a lack of accuracy with respect to the underlying assumptions that these models require. In order to complement these models this paper will discuss an alternative approach that we call value road-mapping. By adapting roadmapping techniques the potential value streams of early stages technologies can be plotted and hence a clearer consensus based picture of the future potential of new technologies emerges. Roadmapping is a workshop-based process bringing together multifunctional perspectives, and supporting communication in particular between technical and commercial groups. The study is work in progress and is based on a growing number of cases. (c) 2006 PICMET.

Feedback control and the arrow of time

The purpose of this paper is to highlight the central role that the time asymmetry of stability plays in feedback control. We show that this provides a new perspective on the use of doubly-infinite or semi-infinite time axes for signal spaces in control theory. We then focus on the implication of this time asymmetry in modeling uncertainty, regulation and robust control. We point out that modeling uncertainty and the ease of control depend critically on the direction of time. We finally discuss the relationship of this control-based time arrow with the well-known arrows of time in physics. © 2008 IEEE.

Erratum: "Zinc oxide nanostructures and high electron mobility nanocomposite thin film transistors" (IEEE Transactions on Electron Devices (2009))

In the above entitled paper (ibid., vol. 55, no. 11, pp. 3001-3011), two errors were noticed after the paper went to press. The errors are corrected here.

Synthesis of positive-real functions with low-complexity series-parallel networks

The purpose of this paper is to continue to develop the recently introduced concept of a regular positive-real function and its application to the classification of low-complexity two-terminal networks. This paper studies five- and six-element series-parallel networks with three reactive elements and presents a complete characterisation and graphical representation of the realisability conditions for these networks. The results are motivated by an approach to passive mechanical control which makes use of the inerter device. ©2009 IEEE.

Model-based approaches to handling additive noise in reverberant environments

Model-based approaches to handle additive and convolutional noise have been extensively investigated and used. However, the application of these schemes to handling reverberant noise has received less attention. This paper examines the extension of two standard additive/convolutional noise approaches to handling reverberant noise. The first is an extension of vector Taylor series (VTS) compensation, reverberant VTS, where a mismatch function including reverberant noise is used. The second scheme modifies constrained MLLR to allow a wide-span of frames to be taken into account and projected into the required dimensionality. To allow additive noise to be handled, both these schemes are combined with standard VTS. The approaches are evaluated and compared on two tasks, MC-WSJ-AV, and a reverberant simulated version of AURORA-4. © 2011 IEEE.

QM/MM simulation of liquid water with an adaptive quantum region.

The simulation of complex chemical systems often requires a multi-level description, in which a region of special interest is treated using a computationally expensive quantum mechanical (QM) model while its environment is described by a faster, simpler molecular mechanical (MM) model. Furthermore, studying dynamic effects in solvated systems or bio-molecules requires a variable definition of the two regions, so that atoms or molecules can be dynamically re-assigned between the QM and MM descriptions during the course of the simulation. Such reassignments pose a problem for traditional QM/MM schemes by exacerbating the errors that stem from switching the model at the boundary. Here we show that stable, long adaptive simulations can be carried out using density functional theory with the BLYP exchange-correlation functional for the QM model and a flexible TIP3P force field for the MM model without requiring adjustments of either. Using a primary benchmark system of pure water, we investigate the convergence of the liquid structure with the size of the QM region, and demonstrate that by using a sufficiently large QM region (with radius 6 Å) it is possible to obtain radial and angular distributions that, in the QM region, match the results of fully quantum mechanical calculations with periodic boundary conditions, and, after a smooth transition, also agree with fully MM calculations in the MM region. The key ingredient is the accurate evaluation of forces in the QM subsystem which we achieve by including an extended buffer region in the QM calculations. We also show that our buffered-force QM/MM scheme is transferable by simulating the solvated Cl(-) ion.