158-μJ pulses from a single-transverse-mode, large-mode-area erbium-doped fiber amplifier

We report the amplification of 10-100-pJ semiconductor diode pulses to an energy of 158 μJ and peak powers >100 kW in a multistage fiber amplifier chain based on a single-mode, large-mode-area erbium-doped amplifier design. To our knowledge these results represent the highest single-mode pulse energy extracted from any doped-fiber system. © 1997 Optical Society of America.

Passive mode-locking of bow-tie lasers

The passive mode-locking in novel double tapered Bow-Tie lasers is investigated. This investigation aims to determine the possible GHz repetition rate at which passive mode-locking is derived, in addition, the record power levels will also be demonstrated. Alternative drive schemes and contact configurations to achieve optimized performance are discussed.

Numerical modelling of dynamic response of loss modulated monolithic multisection mode-locked semiconductor lasers

Monolithic multisection mode-locked semiconductor lasers with an integrated distributed Bragg reflector (DBR) have recently been demonstrated to generate stable picosecond pulses at high repetition rates suitable for optical communication systems. However, there has been very little theoretical work on understanding the physical mechanisms of the device and on optimisation of the absorber modulator design. This article presents numerical modeling of the loss modulated mode-locking process in these lasers. The model predicts most aspects experimentally observed within this type of device, and the results show the output waveform, optical spectrum, instantaneous frequency chirp, and stable operating range.

Post-processing of vertical-cavity surface-emitting lasers for transverse mode and polarization control

The operation on how high quality single-mode operation can be readily attained on etching circles in multimode devices is discussed. Arrays of such spots can also be envisaged. Control of the polarization state is also achieved by use of deep line etches. The output filaments and beam shapes of the conventional multimode vertical cavity surface emitting lasers (VCSEL) is shown to be engineered in terms of their positions, widths, and polarizations by use of focused ion beam etching (FIBE). Several GaAs quantum well top-emitting devices with cavity diameters of 10 μm and 18 μm were investigated.

Low short term timing jitter in an integrated monolithic extended cavity semiconductor mode-locked laser

Jitter measurements were performed on a monolithically integrated active/passive cavity multiple quantum well laser, actively mode-locked at 10 GHz via modulation of an absorber section. Sub-10 ps pulses were produced upon optimization of the drive conditions to the gain, distributed Bragg reflector, and absorber sections. A model was also developed using travelling wave rate equations. Simulation results suggest that spontaneous emission is the dominant cause of jitter, with carrier dynamics having a time constant of the order of 1 ns.

Mode control in vertical-cavity surface-emitting lasers by post-processing using focused ion-beaih etching

Single-mode emission is achieved in previously multimode gain-guided vertical-cavity surface-emitting lasers (VCSEL's) by localized modification of the mirror reflectivity using focused ion-beam etching. Reflectivity engineering is also demonstrated to suppress transverse mode emission in an oxide-confined device, reducing the spectral width from 1.2 nm to less than 0.5 nm.

Mode-controlled vertical cavity surface emitting lasers for bandwidth enhancement of multimode fibre links

A GaAs Vertical Cavity Surface Emitting Laser (VCSEL) that generates controlled modes offset from the center is described. The device is modulated with a 27-1 pseudo-random bit sequence and its output is transmitted along a 1 km length of multimode fiber (MMF). Open eyes are obtained for data rates as high as 1.4Gb/s. The transmission bandwidth increases by a factor of 4 over over-filled launch (OFL). This enhancement is stable against environment influences on the fiber.

Gaussian etched single transverse mode vertical-cavity surface-emitting laser

A continuous Gaussian profile matched to the fundamental mode was etched onto the aperture of a vertical cavity surface emitting laser (VCSEL). Single Gaussian spot emission was achieved over the entire operating current range.

Performance of single mode laser components using 2D photonic lattice reflectors

This paper will report studies of the placement of 2D photonic gratings on either side of the ridge in a Fabry Perot laser device in order to cause single mode emission. Using this approach, side mode suppression ratios of up to 30 dB are achieved, the emission remaining single mode even under 10 Gb/s large signal modulation. It is found that the use of the grating not only causes spectrally dependent reflection but in addition can lead to transverse mode fluctuations. The action of the grating has been studied not just in terms of its edge emission where conversion of the transverse modes is achieved, but also through measurement of the vertical emission from the structure where strong filtering action is observed.

Single-gated multiple-mode power semiconductor devices

A new method has been used to design a power semiconductor device which combines IGBT switching and thyristor on-state characteristics. A single gate signal controls the switching and triggers the transitions between the IGBT and thyristor modes of operation. This paper discusses single-gated devices with multiple modes and aspects of their switching behaviour.

Applications of the dynamic mode decomposition

The decomposition of experimental data into dynamic modes using a data-based algorithm is applied to Schlieren snapshots of a helium jet and to time-resolved PIV-measurements of an unforced and harmonically forced jet. The algorithm relies on the reconstruction of a low-dimensional inter-snapshot map from the available flow field data. The spectral decomposition of this map results in an eigenvalue and eigenvector representation (referred to as dynamic modes) of the underlying fluid behavior contained in the processed flow fields. This dynamic mode decomposition allows the breakdown of a fluid process into dynamically revelant and coherent structures and thus aids in the characterization and quantification of physical mechanisms in fluid flow. © 2010 Springer-Verlag.

Holographic mode-group division multiplexing

Specific fibre modes are deliberately excited in a few-mode and multimode fibre using holography. The same system is also used to demonstrate holography's ability to detect and route individual fibre modes. © 2011 Optical Society of America.

Nanotube-based passively mode-locked Ytterbium-pumped Raman laser

Over the past decades mode-locked fibre lasers have been extensively refined and developed, with most research efforts focussing on employing rare-earth doped fibres as the active elements [1]. This presents the problem that operation is limited to regions of the spectrum where such elements exhibit gain [1]. Raman amplification in silica fibre is an attractive way to overcome this spectral limitation, with gain available across the entire transparency window (300 nm - 2300 nm) [2-4]. There have been a number of reports utilising Raman gain in ultrashort pulse sources [2-4], however none using a broadband saturable absorber, such as carbon nanotubes [5-7] and graphene [7-9]. A broadband saturable absorber is an essential pre-requisite in order to fully exploit the wavelength flexibility provided by the Raman gain in short pulse mode-locked fiber lasers. © 2011 IEEE.

Ultrafast and high-energy pulsed lasers with graphene mode-lockers

The conventional technology for generating ultrashort pulses relies on soliton-like operation based mode-locking. In this regime, the pulse duration is limited by nonlinear optical effects[1]. One method to mitigate these effects is to alternate segments of normal and anomalous group velocity dispersion (GVD) fiber[1]. This configuration is known as dispersion-managed soliton design. It decreases the nonlinear optical effects and reduces the pulse duration[1]. © 2011 IEEE.