Experimental LVRT performance of a 250 kW brushless DFIG

Nowadays, all new wind turbine generators have to meet strict grid codes, especially riding through certain grid faults, such as a low voltage caused by grid short circuits. The Low-Voltage Ride Through (LVRT) capability has become a key issue in assessing the performance of wind turbine generators. The mediumspeed Brushless DFIG in combination with a simplified two-stage gearbox shows commercial promise as a replacement for conventional DFIGs due to its lower cost and higher reliability. Furthermore, the Brushless DFIG has significantly improved LVRT performance when compared with the DFIG due to its inherent design characteristics. In this paper, the authors propose a control strategy for the Brushless DFIG to improve its LVRT performance. The controller has been implemented on a prototype 250 kW Brushless DFIG and test results show that LVRT is possible without a need for any external protective hardware such as a crowbar.

Implementation of trailer steering control on a multi-unit vehicle at high speeds

A high-speed path-following controller for long combination vehicles (LCVs) was designed and implemented on a test vehicle consisting of a rigid truck towing a dolly and a semitrailer. The vehicle was driven through a 3.5 m wide lane change maneuver at 80 km/h. The axles of the dolly and trailer were steered actively by electrically-controlled hydraulic actuators. Substantial performance benefits were recorded compared with the unsteered vehicle. For the best controller weightings, performance improvements relative to unsteered case were: lateral tracking error 75% reduction, rearward amplification (RA) of lateral acceleration 18% reduction, and RA of yaw rate 37% reduction. This represents a substantial improvement in stability margins. The system was found to work well in conjunction with the braking-based stability control system of the towing vehicle with no negative interaction effects being observed. In all cases, the stability control system and the steering system improved the yaw stability of the combination. © 2014 by ASME.

Instantaneous frequency and bandwidth estimation using filterbank arrays

Accurate estimation of the instantaneous frequency of speech resonances is a hard problem mainly due to phase discontinuities in the speech signal associated with excitation instants. We review a variety of approaches for enhanced frequency and bandwidth estimation in the time-domain and propose a new cognitively motivated approach using filterbank arrays. We show that by filtering speech resonances using filters of different center frequency, bandwidth and shape, the ambiguity in instantaneous frequency estimation associated with amplitude envelope minima and phase discontinuities can be significantly reduced. The novel estimators are shown to perform well on synthetic speech signals with frequency and bandwidth micro-modulations (i.e., modulations within a pitch period), as well as on real speech signals. Filterbank arrays, when applied to frequency and bandwidth modulation index estimation, are shown to reduce the estimation error variance by 85% and 70% respectively. © 2013 IEEE.

Determination of the rheological parameters of self-compacting concrete matrix using slump flow test

The classification of a concrete mixture as self-compacting (SCC) is performed by a series of empirical characterization tests that have been designed to assess not only the flowability of the mixture but also its segregation resistance and filling ability. The objective of the present work is to correlate the rheological parameters of SCC matrix, yield stress and plastic viscosity, to slump flow measurements. The focus of the slump flow test investigation was centered on the fully yielded flow regime and an empirical model relating the yield stress to material and flow parameters is proposed. Our experimental data revealed that the time for a spread of 500 mm which is used in engineering practice as reference for measurement parameters, is an arbitrary choice. Our findings indicate that the non-dimensional final spread is linearly related to the non-dimensional yield-stress. Finally, there are strong indications that the non-dimensional viscosity of the mixture is associated with the non-dimensional final spread as well as the stopping time of the slump flow; this experimental data set suggests an exponential decay of the final spread and stopping time with viscosity. © Appl. Rheol.

Stabilising terminal cost and terminal controller for ℓasso- MPC: Enhanced optimality and region of attraction

In recent literature, ℓ1-regularised MPC, or ℓasso-MPC, has been recommended for control tasks involving complex requirements on the control signals, for instance, the simultaneous solution of regulation and sharp control allocation for redundantly-actuated systems. This is due to the implicit thresholding ability of LASSO regression. In this paper, a stabilising terminal cost featuring a mixed ℓ1/ℓ2 2 penalty is presented. Then, a candidate terminal controller is computed, with the aim of enlarging the region of attraction. © 2013 EUCA.

Adaptive enhancement of multimode fibre bandwidth by twin-spot offset launch

A binary grating on a Spatial Light Modulator generates twin antiphase spots with adjustable positions across the core of a multimode fibre allowing adaptive excitation of antisymmetric mode-groups for improving modal dispersion or modal multiplexing. © 2011 AOS.

Experimental demonstration of a transparent graphene millimetre wave absorber with 28% fractional bandwidth at 140 GHz.

The development of transparent radio-frequency electronics has been limited, until recently, by the lack of suitable materials. Naturally thin and transparent graphene may lead to disruptive innovations in such applications. Here, we realize optically transparent broadband absorbers operating in the millimetre wave regime achieved by stacking graphene bearing quartz substrates on a ground plate. Broadband absorption is a result of mutually coupled Fabry-Perot resonators represented by each graphene-quartz substrate. An analytical model has been developed to predict the absorption performance and the angular dependence of the absorber. Using a repeated transfer-and-etch process, multilayer graphene was processed to control its surface resistivity. Millimetre wave reflectometer measurements of the stacked graphene-quartz absorbers demonstrated excellent broadband absorption of 90% with a 28% fractional bandwidth from 125-165 GHz. Our data suggests that the absorbers' operation can also be extended to microwave and low-terahertz bands with negligible loss in performance.

Novel passive launch scheme for ultimate bandwidth improvement of graded-index multimode fibers

We propose a new practical multimode fiber optical launch scheme, providing near single mode group excitation for >5 times transmission bandwidth improvement. Equalization-free transmission of a 10-Gb/s signal over 220-m fiber is achieved in experimental demonstrations. © 2010 Optical Society of America.

Trial Test of a Bulk-Type Fully HTS Synchronous Motor

© 2013 IEEE. The world's first bulk-type fully high temperature superconducting synchronous motor (HTS-SM) was assembled and tested in our laboratory at the University of Cambridge. The fully HTS-SM was designed with 75 Y123 HTS bulks mounted on the surface of the rotor and six air core 2G HTS racetrack coils used for stator windings. We successfully applied a light fan load test for this fully HTS-SM at its operating temperature of 77 K. The detected decay of the trapped magnetic flux densities at the centre of the HTS bulks was up to 16.5% after 5 h of synchronous rotation. Due to the high current density of the HTS material, the ac stator field for the 2G HTS winding was 49.2% stronger compared with a comparable copper winding. In the meantime, we estimated that the efficiency was about 86% potentially under stable low frequency rotation at 150 r/min. The results show that the performance of this HTS motor is acceptable for practical applications.

A preliminary study on methods for retaining data quality problems in automatically generated test data

Data in an organisation often contains business secrets that organisations do not want to release. However, there are occasions when it is necessary for an organisation to release its data such as when outsourcing work or using the cloud for Data Quality (DQ) related tasks like data cleansing. Currently, there is no mechanism that allows organisations to release their data for DQ tasks while ensuring that it is suitably protected from releasing business related secrets. The aim of this paper is therefore to present our current progress on determining which methods are able to modify secret data and retain DQ problems. So far we have identified the ways in which data swapping and the SHA-2 hash function alterations methods can be used to preserve missing data, incorrectly formatted values, and domain violations DQ problems while minimising the risk of disclosing secrets. © (2012) by the AIS/ICIS Administrative Office All rights reserved.