Passive mode-locking of bow-tie lasers

The passive mode-locking in novel double tapered Bow-Tie lasers is investigated. This investigation aims to determine the possible GHz repetition rate at which passive mode-locking is derived, in addition, the record power levels will also be demonstrated. Alternative drive schemes and contact configurations to achieve optimized performance are discussed.

Gain-switched dynamics of tapered waveguide bow-tie lasers

The use of tapered waveguide lasers and amplifiers for enhanced picosecond pulse generation has led to order-of-magnitude peak power and pulse energy improvements. Monolithic pulse generation schemes have so far relied on a double-tapered bow-tie structure. The modeling of tapered lasers has so far been limited to steady-state operation or has lacked experimental comparison. This paper considers both experimentally and theoretically the gain-switched performance of bow-tie lasers of various taper angles. The role of transverse-mode spatial hole burning in tapered waveguide lasers is thereby investigated.

Numerical modelling of dynamic response of loss modulated monolithic multisection mode-locked semiconductor lasers

Monolithic multisection mode-locked semiconductor lasers with an integrated distributed Bragg reflector (DBR) have recently been demonstrated to generate stable picosecond pulses at high repetition rates suitable for optical communication systems. However, there has been very little theoretical work on understanding the physical mechanisms of the device and on optimisation of the absorber modulator design. This article presents numerical modeling of the loss modulated mode-locking process in these lasers. The model predicts most aspects experimentally observed within this type of device, and the results show the output waveform, optical spectrum, instantaneous frequency chirp, and stable operating range.

Beam propagation modelling of tapered waveguide lasers

A dynamic beam propagation model allows design optimization of high power low divergence tapered waveguide lasers. The model is extended to include spatially-resolved temperature profiles and a temperature dependent gain. Using this model, design parameters such as the optimum facet reflectivity, taper angle, and waveguide dimension can be calculated for low far-field divergence and high continuous wave power.

Post-processing of vertical-cavity surface-emitting lasers for transverse mode and polarization control

The operation on how high quality single-mode operation can be readily attained on etching circles in multimode devices is discussed. Arrays of such spots can also be envisaged. Control of the polarization state is also achieved by use of deep line etches. The output filaments and beam shapes of the conventional multimode vertical cavity surface emitting lasers (VCSEL) is shown to be engineered in terms of their positions, widths, and polarizations by use of focused ion beam etching (FIBE). Several GaAs quantum well top-emitting devices with cavity diameters of 10 μm and 18 μm were investigated.

High speed wavelength conversion utilising an integrated amplifier/DFB laser

Wavelength conversion in the 1.55-μm regime was achieved for the first time in an integrated SOA/DFB laser by modulating the output power of the laser with a light beam of a different wavelength externally injected into the SOA section. In terms of speed, response times as low as 13ps were observed, though at the expense of reduced extinction ratio. Generally, these results indicate that operation in the 10s of GB/s should be possible.

Mode control in vertical-cavity surface-emitting lasers by post-processing using focused ion-beaih etching

Single-mode emission is achieved in previously multimode gain-guided vertical-cavity surface-emitting lasers (VCSEL's) by localized modification of the mirror reflectivity using focused ion-beam etching. Reflectivity engineering is also demonstrated to suppress transverse mode emission in an oxide-confined device, reducing the spectral width from 1.2 nm to less than 0.5 nm.

Design of high power tapered waveguide semiconductor lasers

An advanced beam propagation model was developed to show that the far field narrows with good suppression of higher order modes for an appropriate temperature rise, without significant power penalty. To verify the accuracy of the model, the dependence of far field pattern on bias conditions were assessed both experimentally and theoretically, initially under pulsed conditions to reduce thermal effects. The results highlight the optimum taper angle and the role of local heating effects.

Wavelength conversion based on an integrated semiconductor optical amplifier/DFB laser at 10 Gb/s with low input power

A study of the relative performance of an integrated semiconductor optical amplifier (SOA)/distributed feedback laser wavelength converter that can operate with negative penalties at 10 Gb/s rates is conducted. It is found that reduction of more than 25 times in required input powers are achieved when compared with laser or SOA converters.

Mode-controlled vertical cavity surface emitting lasers for bandwidth enhancement of multimode fibre links

A GaAs Vertical Cavity Surface Emitting Laser (VCSEL) that generates controlled modes offset from the center is described. The device is modulated with a 27-1 pseudo-random bit sequence and its output is transmitted along a 1 km length of multimode fiber (MMF). Open eyes are obtained for data rates as high as 1.4Gb/s. The transmission bandwidth increases by a factor of 4 over over-filled launch (OFL). This enhancement is stable against environment influences on the fiber.

High bandwidth multimode fiber links using subcarrier multiplexing in vertical-cavity surface-emitting lasers

The usage of subcarrier multiplexing (SCM) techniques to allow link transmission in excess of the specified fiber bandwidth is described. A series of 200-Mbit/s channels with carrier frequencies of up to more than twenty times the 3-dB fiber bandwidth have been successfully used, the maximum being limited by the available electronics. To assess the transmission of the fiber, digitally modulated channels are placed on high frequency carrier signals and then used to modulate a vertical-cavity surface-emitting lasers (VCSEL).

Mechanism of polarization pinning in vertical cavity surface emitting lasers using focused ion beam etching

Photoluminescence experiments have identified strain as the origin for polarization pinning in vertical cavity surface emitting lasers post-processed by focused ion beam etching. Theoretical models were applied to deduce the strain in devices. Post-annealing was used to optimize polarization pinning.

Spatial emission control of vertical cavity surface emitting lasers to provide bandwidth gain in multimode fibre links using a simple alignment technique

Etched VCSEL sources are reported which avoid bandwidth collapse in multimode fibre using a simple coupling technique to control the launch. These devices have allowed better than over-filled launch bandwidth for alignment tolerances of ±7 microns.

Feasibility of AlGaInAs lasers for high speed uncooled communication systems

The feasibility of using AlGaInAs lasers for high-speed modulation at high temperatures was evaluated and compared with performance of GaInAsP devices. Both drift-diffusion and rate equation simulation were involved so that the temperature dependence of material parameters was found in terms of overall dynamic performance. Differential gain was estimated by means of drift-diffusion simulations.