Optimal Correction for Guessing in Multiple-Choice Tests

Building on Item Response Theory we introduce students’ optimal behavior in multiple-choice tests. Our simulations indicate that the optimal penalty is relatively high, because although correction for guessing discriminates against risk-averse subjects, this effect is small compared with the measurement error that the penalty prevents. This result obtains when knowledge is binary or partial, under different normalizations of the score, when risk aversion is related to knowledge and when there is a pass-fail break point. We also find that the mean degree of difficulty should be close to the mean level of knowledge and that the variance of difficulty should be high.

Another Look to the Price-Dividend Ratio: A Markov-Switching Approach

This paper analyzes the stationarity of this ratio in the context of a Markov-switching model à la Hamilton (1989) where an asymmetric speed of adjustment is introduced. This particular specification robustly supports a nonlinear reversion process and identifies two relevant episodes: the post-war period from the mid-50’s to the mid-70’s and the so called “90’s boom” period. A three-regime Markov-switching model displays the best regime identification and reveals that only the first part of the 90’s boom (1985-1995) and the post-war period are near-nonstationary states. Interestingly, the last part of the 90’s boom (1996-2000), characterized by a growing price-dividend ratio, is entirely attributed to a regime featuring a highly reverting process.

Efectos tamaño y sector sobre la rentabilidad, endeudamiento y coste de la deuda de las empresas familiares riojanas

Ponencia presentada y defendida en las XIV jornadas Hispano Lusas de Gestión Científica celebradas en Azores en febrero de 2004.

Second-to-Fourth Digit Ratio Has a Non-Monotonic Impact on Altruism

Gene-culture co-evolution emphasizes the joint role of culture and genes for the emergence of altruistic and cooperative behaviors and behavioral genetics provides estimates of their relative importance. However, these approaches cannot assess which biological traits determine altruism or how. We analyze the association between altruism in adults and the exposure to prenatal sex hormones, using the second-to-fourth digit ratio. We find an inverted U-shaped relation for left and right hands, which is very consistent for men and less systematic for women. Subjects with both high and low digit ratios give less than individuals with intermediate digit ratios. We repeat the exercise with the same subjects seven months later and find a similar association, even though subjects' behavior differs the second time they play the game. We then construct proxies of the median digit ratio in the population (using more than 1000 different subjects), show that subjects' altruism decreases with the distance of their ratio to these proxies. These results provide direct evidence that prenatal events contribute to the variation of altruistic behavior and that the exposure to fetal hormones is one of the relevant biological factors. In addition, the findings suggest that there might be an optimal level of exposure to these hormones from social perspective.

Stability and Limit Oscillations of a Control Event-Based Sampling Criterion

This paper investigates the presence of limit oscillations in an adaptive sampling system. The basic sampling criterion operates in the sense that each next sampling occurs when the absolute difference of the signal amplitude with respect to its currently sampled signal equalizes a prescribed threshold amplitude. The sampling criterion is extended involving a prescribed set of amplitudes. The limit oscillations might be interpreted through the equivalence of the adaptive sampling and hold device with a nonlinear one consisting of a relay with multiple hysteresis whose parameterization is, in general, dependent on the initial conditions of the dynamic system. The performed study is performed on the time domain.

Seasonal Stability Tests in gretl. An Application to International Tourism Data

The seasonal stability tests of Canova & Hansen (1995) (CH) provide a method complementary to that of Hylleberg et al. (1990) for testing for seasonal unit roots. But the distribution of the CH tests are unknown in small samples. We present a method to numerically compute critical values and P-values for the CH tests for any sample size and any seasonal periodicity. In fact this method is applicable to the types of seasonality which are commonly in use, but also to any other.

An Alternative View of the US Price-Dividend Ratio Dynamics

As a necessary condition for the validity of the present value model, the price-dividend ratio must be stationary. However, significant market episodes seem to provide evidence of prices significantly drifting apart from dividends while other episodes show prices anchoring back to dividends. This paper investigates the stationarity of this ratio in the context of a Markov- switching model à la Hamilton (1989) where an asymmetric speed of adjustment towards a unique attractor is introduced. A three-regime model displays the best regime identification and reveals that the first part of the 90’s boom (1985-1995) and the post-war period are characterized by a stationary state featuring a slow reverting process to a relatively high attractor. Interestingly, the latter part of the 90’s boom (1996-2000), characterized by a growing price-dividend ratio, is entirely attributed to a stationary regime featuring a highly reverting process to the attractor. Finally, the post-Lehman Brothers episode of the subprime crisis can be classified into a temporary nonstationary regime.

Judgmental-analytical procedures for adapting tests: Adaptation to Spanish of the Reasoning Tests Battery

Adapting a test between cultures or languages requires taking into account legal, linguistic, metric, and use-related considerations. Significantly more attention has been paid to the methodological aspects involved in the study of metric equivalence than to judgmental-analytical procedures prior to the empirical confirmation stage. However, considering the latter is crucial in the adaptation process. Along these lines, this paper seeks to describe and focus on the relevance of the previous stages, thereby offering a systematization process that comprises ten sections. This approach contributes to ensuring the construction of a test adapted and equivalent in as much as possible to the original. This process is exemplified by means of a Spanish language adaptation of a cognitive test originally designed in Portuguese for the Portuguese population, the Reasoning Test Battery. Copyright (C) 2013, Konrad Lorenz University Foundation. Published by Elsevier Espana, S.L.U.

Advanced Reaction Systems for Hydrogen Production

[EN] This PhD work started in March 2010 with the support of the University of the Basque Country (UPV/EHU) under the program named “Formación de Personal Investigador” at the Chemical and Environmental Engineering Department in the Faculty of Engineering of Bilbao. The major part of the Thesis work was carried out in the mentioned department, as a member of the Sustainable Process Engineering (SuPrEn) research group. In addition, this PhD Thesis includes the research work developed during a period of 6 months at the Institut für Mikrotechnik Mainz GmbH, IMM, in Germany. During the four years of the Thesis, conventional and microreactor systems were tested for several feedstocks renewable and non-renewable, gases and liquids through several reforming processes in order to produce hydrogen. For this purpose, new catalytic formulations which showed high activity, selectivity and stability were design. As a consequence, the PhD work performed allowed the publication of seven scientific articles in peer-reviewed journals. This PhD Thesis is divided into the following six chapters described below. The opportunity of this work is established on the basis of the transition period needed for moving from a petroleum based energy system to a renewable based new one. Consequently, the present global energy scenario was detailed in Chapter 1, and the role of hydrogen as a real alternative in the future energy system was justified based on several outlooks. Therefore, renewable and non-renewable hydrogen production routes were presented, explaining the corresponding benefits and drawbacks. Then, the raw materials used in this Thesis work were described and the most important issues regarding the processes and the characteristics of the catalytic formulations were explained. The introduction chapter finishes by introducing the concepts of decentralized production and process intensification with the use of microreactors. In addition, a small description of these innovative reaction systems and the benefits that entailed their use were also mentioned. In Chapter 2 the main objectives of this Thesis work are summarized. The development of advanced reaction systems for hydrogen rich mixtures production is the main objective. In addition, the use and comparison between two different reaction systems, (fixed bed reactor (FBR) and microreactor), the processing of renewable raw materials, the development of new, active, selective and stable catalytic formulations, and the optimization of the operating conditions were also established as additional partial objectives. Methane and natural gas (NG) steam reforming experimental results obtained when operated with microreactor and FBR systems are presented in Chapter 3. For these experiments nickel-based (Ni/Al2O3 and Ni/MgO) and noble metal-based (Pd/Al2O3 and Pt/Al2O3) catalysts were prepared by wet impregnation and their catalytic activity was measured at several temperatures, from 973 to 1073 K, different S/C ratios, from 1.0 to 2.0, and atmospheric pressure. The Weight Hourly Space Velocity (WHSV) was maintained constant in order to compare the catalytic activity in both reaction systems. The results obtained showed a better performance of the catalysts operating in microreactors. The Ni/MgO catalyst reached the highest hydrogen production yield at 1073 K and steam-to-carbon ratio (S/C) of 1.5 under Steam methane Reforming (SMR) conditions. In addition, this catalyst also showed good activity and stability under NG reforming at S/C=1.0 and 2.0. The Ni/Al2O3 catalyst also showed high activity and good stability and it was the catalyst reaching the highest methane conversion (72.9 %) and H2out/CH4in ratio (2.4) under SMR conditions at 1073 K and S/C=1.0. However, this catalyst suffered from deactivation when it was tested under NG reforming conditions. Regarding the activity measurements carried out with the noble metal-based catalysts in the microreactor systems, they suffered a very quick deactivation, probably because of the effects attributed to carbon deposition, which was detected by Scanning Electron Microscope (SEM). When the FBR was used no catalytic activity was measured with the catalysts under investigation, probably because they were operated at the same WHSV than the microreactors and these WHSVs were too high for FBR system. In Chapter 4 biogas reforming processes were studied. This chapter starts with an introduction explaining the properties of the biogas and the main production routes. Then, the experimental procedure carried out is detailed giving concrete information about the experimental set-up, defining the parameters measured, specifying the characteristics of the reactors used and describing the characterization techniques utilized. Each following section describes the results obtained from activity testing with the different catalysts prepared, which is subsequently summarized: Section 4.3: Biogas reforming processes using γ-Al2O3 based catalysts The activity results obtained by several Ni-based catalysts and a bimetallic Rh-Ni catalyst supported on magnesia or alumina modified with oxides like CeO2 and ZrO2 are presented in this section. In addition, an alumina-based commercial catalyst was tested in order to compare the activity results measured. Four different biogas reforming processes were studied using a FBR: dry reforming (DR), biogas steam reforming (BSR), biogas oxidative reforming (BOR) and tri-reforming (TR). For the BSR process different steam to carbon ratios (S/C) from 1.0 to 3.0, were tested. In the case of BOR process the oxygen-to-methane (O2/CH4) ratio was varied from 0.125 to 0.50. Finally, for TR processes different S/C ratios from 1.0 to 3.0, and O2/CH4 ratios of 0.25 and 0.50 were studied. Then, the catalysts which achieved high activity and stability were impregnated in a microreactor to explore the viability of process intensification. The operation with microreactors was carried out under the best experimental conditions measured in the FBR. In addition, the physicochemical characterization of the fresh and spent catalysts was carried out by Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES), N2 physisorption, H2 chemisorption, Temperature Programmed Reduction (TPR), SEM, X-ray Photoelectron Spectroscopy (XPS) and X-ray powder Diffraction (XRD). Operating with the FBR, conversions close to the ones predicted by thermodynamic calculations were obtained by most of the catalysts tested. The Rh-Ni/Ce-Al2O3 catalyst obtained the highest hydrogen production yield in DR. In BSR process, the Ni/Ce-Al2O3 catalyst achieved the best activity results operating at S/C=1.0. In the case of BOR process, the Ni/Ce-Zr-Al2O3 catalyst showed the highest reactants conversion values operating at O2/CH4=0.25. Finally, in the TR process the Rh-Ni/Ce-Al2O3 catalyst obtained the best results operating at S/C=1.0 and O2/CH4=0.25. Therefore, these three catalysts were selected to be coated onto microchannels in order to test its performance under BOR and TR processes conditions. Although the operation using microreactors was carried out under considerably higher WHSV, similar conversions and yields as the ones measured in FBR were measured. Furthermore, attending to other measurements like Turnover Frequency (TOF) and Hydrogen Productivity (PROD), the values calculated for the catalysts tested in microreactors were one order of magnitude higher. Thus, due to the low dispersion degree measured by H2-chemisorption, the Ni/Ce-Al2O3 catalyst reached the highest TOF and PROD values. Section 4.4: Biogas reforming processes using Zeolites L based catalysts In this section three type of L zeolites, with different morphology and size, were synthesized and used as catalyst support. Then, for each type of L zeolite three nickel monometallic and their homologous Rh-Ni bimetallic catalysts were prepared by the wetness impregnation method. These catalysts were tested using the FBR under DR process and different conditions of BSR (S/C ratio of 1.0 and 2.0), BOR (O2/CH4 ratio of 0.25 and 0.50) and TR processes (at S/C=1.0 and O2/CH4=0.25). The characterization of these catalysts was also carried out by using the same techniques mentioned in the previous section. Very high methane and carbon dioxide conversion values were measured for almost all the catalysts under investigation. The experimental results evidenced the better catalytic behavior of the bimetallic catalysts as compared to the monometallic ones. Comparing the catalysts behavior with regards to their morphology, for the BSR process the Disc catalysts were the most active ones at the lowest S/C ratio tested. On the contrary, the Cylindrical (30–60 nm) catalysts were more active under BOR conditions at O2/CH4=0.25 and TR processes. By the contrary, the Cylindrical (1–3 µm) catalysts showed the worst activity results for both processes. Section 4.5: Biogas reforming processes using Na+ and Cs+ doped Zeolites LTL based catalysts A method for the synthesis of Linde Type L (LTL) zeolite under microwave-assisted hydrothermal conditions and its behavior as a support for heterogeneously catalyzed hydrogen production is described in this section. Then, rhodium and nickel-based bimetallic catalysts were prepared in order to be tested by DR process and BOR process at O2/CH4=0.25. Moreover, the characterization of the catalysts under investigation was also carried out. Higher activities were achieved by the catalysts prepared from the non-doped zeolites, Rh-Ni/D and Rh-Ni/N, as compared to the ones supported on Na+ and Cs+ exchanged supports. However, the differences between them were not very significant. In addition, the Na+ and Cs+ incorporation affected mainly to the Disc catalysts. Comparing the results obtained by these catalysts with the ones studied in the section 4.4, in general worst results were achieved under DR conditions and almost the same results when operated under BOR conditions. In Chapter 5 the ethylene glycol (EG) as feed for syngas production by steam reforming (SR) and oxidative steam reforming (OSR) was studied by using microchannel reactors. The product composition was determined at a S/C of 4.0, reaction temperatures between 625°C and 725°C, atmospheric pressure and Volume Hourly Space Velocities (VHSV) between 100 and 300 NL/(gcath). This work was divided in two sections. The first one corresponds to the introduction of the main and most promising EG production routes. Then, the new experimental procedure is detailed and the information about the experimental set-up and the measured parameters is described. The characterization was carried out using the same techniques as for the previous chapter. Then, the next sections correspond to the catalytic activity and catalysts characterization results. Section 5.3: xRh-cm and xRh-np catalysts for ethylene glycol reforming Initially, catalysts with different rhodium loading, from 1.0 to 5.0 wt. %, and supported on α-Al2O3 were prepared by two different preparation methods (conventional impregnation and separate nanoparticle synthesis). Then, the catalysts were compared regarding their measured activity and selectivity, as well as the characterization results obtained before and after the activity tests carried out. The samples prepared by a conventional impregnation method showed generally higher activity compared to catalysts prepared from Rh nanoparticles. By-product formation of species such as acetaldehyde, ethane and ethylene was detected, regardless if oxygen was added to the feed or not. Among the catalysts tested, the 2.5Rh-cm catalyst was considered the best one. Section 5.4: 2.5Rh-cm catalyst support modification with CeO2 and La2O3 In this part of the Chapter 5, the catalyst showing the best performance in the previous section, the 2.5Rh-Al2O3 catalyst, was selected in order to be improved. Therefore, new Rh based catalysts were designed using α-Al2O3 and being modified this support with different contents of CeO2 or La2O3 oxides. All the catalysts containing additives showed complete conversion and selectivities close to the equilibrium in both SR and OSR processes. In addition, for these catalysts the concentrations measured for the C2H4, CH4, CH3CHO and C2H6 by-products were very low. Finally, the 2.5Rh-20Ce catalyst was selected according to its catalytic activity and characterization results in order to run a stability test, which lasted more than 115 hours under stable operation. The last chapter, Chapter 6, summarizes the main conclusions achieved throughout this Thesis work. Although very high reactant conversions and rich hydrogen mixtures were obtained using a fixed bed reaction system, the use of microreactors improves the key issues, heat and mass transfer limitations, through which the reforming reactions are intensified. Therefore, they seem to be a very interesting and promising alternative for process intensification and decentralized production for remote application.

Reciclado de polvo inconel 718 y evolución de las propiedades de los componentes fabricados con los mismos.

[ES]El objetivo de este trabajo ha sido la determinación de un proceso para la reutilización del polvo metálico desperdiciado durante el proceso de aporte por láser. El polvo necesita ser inyectado para ser fundido directamente sobre el aporte pero un alto porcentaje de las partículas golpean el área no fundida y directamente rebotan fuera de la zona de aporte. La eficiencia de las partículas depositadas puede bajar hasta el 40 % dependiendo de la configuración y del tamaño del punto de aporte. El material utilizado ha sido la superaleación de níquel Inconel 718 debido a su potencial aplicación en procesos de fabricación aditiva. Después del primer uso, el polvo es recolectado y tamizado. La fracción indeseada es magnéticamente segregada y la parte limpia es nuevamente tamizada para obtener datos y de nuevo mezclada para estar lista para la reutilización. No ha sido añadido polvo nuevo a la fracción recuperada y este procedimiento ha sido repetido 5 veces. Los test experimentales muestran que el material depositado presenta resultados similares a aquellos obtenidos con polvo nuevo. La implementación de este proceso permite la mejora de la eficiencia final reduciendo tanto costes como residuos materiales.

Gipuzkoako udalen finantza kaudimenaren rankinga ratio aipagarrienen analisiaren arabera

[EU]Lan honen helburu nagusia,Gipuzkoako udalen finantza kaudimena aztertzeaz gain, beraien arteko konparaketa bat egin ahal izatea zen. Beste modu batera esanda,egoera hobeagoan dauden udalak nortzuk diren identifikatu ahal izatea. Hasi aurretik bagenekien, ordea, udal baten finantza kaudimena ez dagoela faktore bat edo biren arabera soilik, eta gauza asko subjektiboak direla ere bai. Gainera, eragina duten baldintza guztiak kontuan hartzea ere zaila da. Kasu honetan, 9-10 adierazle aukeratu dira, ondoren udal bakoitzak besteekin konparatuz adierazle horretan lortutako zenbatekoa 1etik 10erako puntuazio batekin baloratu da, eta azkenik, udaletxe guztien ranking bat osatu da. Ondorengo lerroetan ikus daiteke ranking honen testuingurua,erabilitako metodologia eta egindako kalkuluen ondorio nagusiak ere.

Gipuzkoako udalen finantza kaudimenaren rankinga ratio aipagarrienen analisiaren arabera

Gipuzkoako udalen finantza kaudimenari buruzko analisi bat burutu ondoren, hauen rankinga burutzea da GrAL honen helburu nagusia.