Métodos de desacoplo de antenas PIFA en terminales móviles

[ES]Hoy en día, los sistemas de comunicación inalámbricos soportan un amplio número de servicios como la voz, datos y vídeos que requieren unas grandes tasas de transmisión. Por ello la mejora de la calidad del enlace que ofrecen los sistemas MIMO es clave. El problema surge al colocar varias antenas en un terminal móvil sin que aparezca un acoplamiento entre las distintas antenas que evite el correcto funcionamiento de estas. En este documento se realizará un estudio de los diferentes métodos de desacoplo entre antenas PIFA (Planar Inverted-F antenna) en un terminal móvil.

In Vitro Surfactant and Perfluorocarbon Aerosol Deposition in a Neonatal Physical Model of the Upper Conducting Airways

Objective: Aerosol delivery holds potential to release surfactant or perfluorocarbon (PFC) to the lungs of neonates with respiratory distress syndrome with minimal airway manipulation. Nevertheless, lung deposition in neonates tends to be very low due to extremely low lung volumes, narrow airways and high respiratory rates. In the present study, the feasibility of enhancing lung deposition by intracorporeal delivery of aerosols was investigated using a physical model of neonatal conducting airways. Methods: The main characteristics of the surfactant and PFC aerosols produced by a nebulization system, including the distal air pressure and air flow rate, liquid flow rate and mass median aerodynamic diameter (MMAD), were measured at different driving pressures (4-7 bar). Then, a three-dimensional model of the upper conducting airways of a neonate was manufactured by rapid prototyping and a deposition study was conducted. Results: The nebulization system produced relatively large amounts of aerosol ranging between 0.3 +/- 0.0 ml/min for surfactant at a driving pressure of 4 bar, and 2.0 +/- 0.1 ml/min for distilled water (H(2)Od) at 6 bar, with MMADs between 2.61 +/- 0.1 mu m for PFD at 7 bar and 10.18 +/- 0.4 mu m for FC-75 at 6 bar. The deposition study showed that for surfactant and H(2)Od aerosols, the highest percentage of the aerosolized mass (similar to 65%) was collected beyond the third generation of branching in the airway model. The use of this delivery system in combination with continuous positive airway pressure set at 5 cmH(2)O only increased total airway pressure by 1.59 cmH(2)O at the highest driving pressure (7 bar). Conclusion: This aerosol generating system has the potential to deliver relatively large amounts of surfactant and PFC beyond the third generation of branching in a neonatal airway model with minimal alteration of pre-set respiratory support.

Kautxu birziklatuzko materialek inpaktura duten erantzunaren simulazioa.

[EU]Ondorengo lanean ingeniaritzaren eremuan aurkitzen den eginkizunik garrantzitsuenetako bat egingo da: material berri bat karakterizatu. Hau da, errealitatean ikusten duguna era matematiko batean idatzi, edo beste era batean esanda, modelo matematiko bat lortu. Jorratuko den materiala kautxu birziklatua izango da, pneumatiko zaharretatik abiatuz egiten dena. Material honek, besteak beste, hurrengo abantailak ditu: produzitzeko erraza (beraz, prezio ekonomikoak, lehengaiak hondakin solidoak direla ikusita) eta inpakturako erantzun ona. Kautxu hau, beste erabileren artean, segurtasun-errailetan erabiltzen da, moto-gidariak ebaketetatik babesteko. Modelo matematikoa edo konstitutiboa lortzeko, lege hiperelastiko eta biskoelastikoetatik abiatuz, portaera bisko-hiperelastikorako lege bat proposatuko da. Lege hau deformazio handietarako eta deformazio abiadura handietarako aplikatu egingo da. Honen oinarria aurreko urteetan eskola honetako beste ikasleek eginiko gradu eta karrera amaierako lanak izango dira. Behin hau izanda, elementu finituetako software baten bidez simulatuko da, eta emaitza numerikoak esperimentalekin alderatuko dira. Honen bidez, modeloa hobetu ahal izango dugu, zehaztasun gehiago lortzeko asmoz.