Characterization of sea water ageing effects on mechanical properties of carbon/epoxy composites for tidal turbine blades

In recent years, many tidal turbine projects have been developed using composites blades. Tidal turbine blades are subject to ocean forces and sea water aggressions, and the reliability of these components is crucial to the profitability of ocean energy recovery systems. The majority of tidal turbine developers have preferred carbon/epoxy blades, so there is a need to understand how prolonged immersion in the ocean affects these composites. In this study the long term behaviour of different carbon/epoxy composites has been studied using accelerated ageing tests. A significant reduction of composite strengths has been observed after saturation of water in the material. For longer immersions only small further changes in these properties occur. No significant changes have been observed for moduli nor for composite toughness. The effect of sea water ageing on damage thresholds and kinetics has been studied and modelled. After saturation, the damage threshold is modified while kinetics of damage development remain the same.

Lipid and lipid carbon stable isotope composition of the hydrothermal vent shrimp Mirocaris fortunata: evidence for nutritional dependence on photosynthetically fixed carbon

Mirocaris fortunata were sampled from the Lucky Strike hydrothermal vent area (Eiffel Tower site) on the mid-Atlantic ridge during the French DIVA 2 cruise (June 1994). Small adults (17 to 22 mm total length), although morphologically identical, could be divided into 2 categories on the basis of pigmentation, lipid composition and C-13/C-12 stable isotope ratios of fatty acids. Highly pigmented small adults (8.6 to 9.2 mu g carotenoid shrimp(-1)) contained higher levels of total lipid than similar-sized individuals containing lower levels of pigment (0.9 to 2.9 mu g carotenoid shrimp(-1)). Lipid class analysis indicated that wax esters comprised 62.5% of total lipid in the former group. These pigmented shrimp also contained high proportions of polyunsaturated fatty acids (PUFA), particularly the phototrophic microplanktonic markers 20:5(n-3) and 22:6(n-3) (14.0 and 33.5% respectively). By contrast small adults (22 mm) and adult shrimp (25 to 26 mm) with low levels of carotenoid pigmentation contained lower amounts of total lipid, little or no wax ester and low levels of 20:5(n-3) and 22:6(n-3), but did contain 16:2(n-4) and 18:2(n-4) and the non-methylene interrupted dienes 20:2 Delta 5,13 and 22:2 Delta 7,15. GC-IRMS analysis of all fatty acids and fatty alcohols in the pigmented small adults indicated delta(13)C values of -18.2 to -27.7 parts per thousand, which is consistent with a photosynthetic carbon source for these compounds. The C-13/C-12 isotope composition of fatty acids from low-pigmented small adults and adults was more variable (-12.5 to -33.1 parts per thousand) and suggests a bimodal distribution which may be attributable to differing nutritional sources or the physiological/reproductive status of these shrimp. Samples of eggs, which are carried by the female on the pleopods, represented approximately 57% of total somatic lipid which indicates a substantial reproductive investment by this species. The egg lipids comprised high proportions of triacylglycerols (64.4 to 78.0% of total lipid) whilst the fatty acid composition was dominated by the monounsaturated fatty acids 16:1(n-7), 18:1(n-7) and 18:1(n-9), which accounted for 65.7 to 33.5% of total fatty acids. By contrast, PUFA were relatively minor components of egg lipids, particularly 20:5(n-3) and 22:6(n-3), which accounted for only 1.1 and 2.9% of total egg fatty acids respectively. This indicates that the reproductive investment by this species is supported mainly by material derived from bacterial chemosynthesis. The potential for M. fortunata hedge betting by producing larvae which either metamorphose at the vent site or adopt a bathypelagic lifestyle and delay metamorphosis to facilitate more widespread dispersal is discussed.

Corrosion of stainless steel components in seawater reverse osmosis desalination plants-investigations on adapted internal cathodic protection

Stainless steel is widely used in seawater reverse osmosis units (SWRO) for both good mechanical and corrosion resistance properties. However, many corrosion failures of stainless steel in SWRO desalination units have been reported. These failures may often be attributed to un-adapted stainless steel grade selection and/or to the particular aggressive seawater conditions in "warm" regions (high ambient temperature, severe biofouling, etc.). Cathodic protection (CP) is a well-known efficient system to prevent corrosion of metallic materials in seawater. It is successfully used in the oil and gas industry to protect carbon steel structures exposed in open-sea. However, the specific service conditions of SWRO units may seriously affect the efficiency of such anti-corrosion system (high flow rates, large stainless steel surfaces affected by biofouling, confinement limiting protective cathodic current flow, etc.). Hence, CP in SWRO units should be considered with special care and modeling appears as useful tool to assess an appropriate CP design. However, there is a clear lack of CP data that could be transposed to SWRO service conditions (i.e. stainless steel, effect of biofouling, high flow rate, etc.). From this background a Join Industry Program was initiated including laboratory exposures, field measurements in a full scale SWRO desalination plant, and modeling work using PROCOR software. The present paper reviews the main parameters affecting corrosion of stainless steel alloys in seawater reverse osmosis units. CP on specific stainless steel devices was investigated in order to assess its actual efficiency for SWRO units. Severe environmental conditions were intentionally used to promote corrosion on the tested stainless steel products in order to evaluate the efficiency of CP. The study includes a modeling work aiming at predicting and designing adapted CP protection to modeled stainless steel units. An excellent correlation between modeling work and field measurements was found.